This documentation has been moved
Configuring ICMP Path Echo Operations
Downloads: This chapterpdf (PDF - 202.0KB) The complete bookPDF (PDF - 5.39MB) | Feedback

Configuring Cisco IOS IP SLAs ICMP Path Echo Operations

Table Of Contents

Configuring Cisco IOS IP SLAs ICMP Path Echo Operations

Finding Feature Information

Contents

Restrictions for IP SLAs ICMP Path Echo Operations

Information About IP SLAs ICMP Path Echo Operations

ICMP Path Echo Operation

How to Configure IP SLAs ICMP Path Echo Operations

Configuring an ICMP Path Echo Operation on the Source Device

Configuring a Basic ICMP Path Echo Operation on the Source Device

Configuring an ICMP Path Echo Operation with Optional Parameters on the Source Device

Scheduling IP SLAs Operations

Examples

Troubleshooting Tips

What to Do Next

Configuration Examples for IP SLAs ICMP Path Echo Operations

Example: Configuring an ICMP Path Echo Operation

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for IP SLAs ICMP Path Echo Operations


Configuring Cisco IOS IP SLAs ICMP Path Echo Operations


First Published: August 14, 2006
Last Updated: January 7, 2011


This module describes how to configure a Cisco IOS IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Path Echo operation to monitor end-to-end and hop-by-hop response time between a Cisco router and devices using IP. ICMP Path Echo is useful for determining network availability and for troubleshooting network connectivity issues. The results of the ICMP Path Echo operation can be displayed and analyzed to determine how ICMP is performing.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for IP SLAs ICMP Path Echo Operations" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

Restrictions for IP SLAs ICMP Path Echo Operations

Information About IP SLAs ICMP Path Echo Operations

How to Configure IP SLAs ICMP Path Echo Operations

Configuration Examples for IP SLAs ICMP Path Echo Operations

Additional References

Feature Information for IP SLAs ICMP Path Echo Operations

Restrictions for IP SLAs ICMP Path Echo Operations

We recommend using a Cisco networking device as the destination device although any networking device that supports RFC 862, Echo protocol, can be used.

Information About IP SLAs ICMP Path Echo Operations

ICMP Path Echo Operation

ICMP Path Echo Operation

To monitor ICMP Path Echo performance on a device, use the IP SLAs ICMP Path Echo operation. An ICMP Path Echo operation measures end-to-end and hop-by-hop response time between a Cisco router and devices using IP. ICMP Path Echo is useful for determining network availability and for troubleshooting network connectivity issues.

The IP SLAs ICMP Path Echo operation records statistics for each hop along the path that the IP SLAs operation takes to reach its destination. The ICMP Path Echo operation determines this hop-by-hop response time between a Cisco router and any IP device on the network by discovering the path using the traceroute facility.

In Figure 1 the source IP SLAs device uses traceroute to discover the path to the destination IP device. A ping is then used to measure the response time between the source IP SLAs device and each subsequent hop in the path to the destination IP device.

Figure 1 ICMP Path Echo Operation

Using the statistics recorded for the response times and availability, the ICMP Path Echo operation can identify a hop in the path that is causing a bottleneck.

How to Configure IP SLAs ICMP Path Echo Operations

Configuring an ICMP Path Echo Operation on the Source Device (required)

Scheduling IP SLAs Operations (required)

Configuring an ICMP Path Echo Operation on the Source Device


Note This operation does not require an IP SLAs Responder on the destination device.


Perform only one of the following tasks:

Configuring a Basic ICMP Path Echo Operation on the Source Device

Configuring an ICMP Path Echo Operation with Optional Parameters on the Source Device

Configuring a Basic ICMP Path Echo Operation on the Source Device

Perform this task to enable and schedule an ICMP Path Echo operation without any optional parameters.


Note For information about scheduling a group of operations, see the "IP SLAs—Multioperation Scheduling of IP SLAs Operations" module of the Cisco IOS IP SLAs Configuration Guide.


SUMMARY STEPS

1. enable

2. configure terminal

3. ip sla operation-number

4. path-echo {destination-ip-address | destination-hostname} [source-ip {ip-address | hostname}]

5. frequency seconds

6. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ip sla operation-id

Example:

Router(config)# ip sla 7

Specifies an ID number for the operation being configured, and enters IP SLA configuration mode.

Step 4 

path-echo {destination-ip-address | destination-hostname} [source-ip {ip-address | hostname}]

Example:

Router(config-ip-sla)# path-echo protocol 172.29.139.134

Defines a Path Echo operation and enters IP SLA Path Echo configuration mode.

Step 5 

frequency seconds

Example:

Router(config-ip-sla-pathEcho)# frequency 30

(Optional) Sets the rate at which a specified IP SLAs operation repeats.

Step 6 

end

Example:

Router(config-ip-sla-pathEcho)# end

Exits to privileged EXEC mode.

Example

The following example shows the configuration of the IP SLAs ICMP Path Echo operation number 7 that will start in 30 seconds and run for 5 minutes.

ip sla 7
 path-echo 172.29.139.134
 frequency 30
!
ip sla schedule 7 start-time after 00:00:30 life 300

Configuring an ICMP Path Echo Operation with Optional Parameters on the Source Device

SUMMARY STEPS

1. enable

2. configure terminal

3. ip sla operation-number

4. path-echo {destination-ip-address | destination-hostname} [source-ip {ip-address | hostname}]

5. history buckets-kept size

6. history distributions-of-statistics-kept size

7. history enhanced [interval seconds] [buckets number-of-buckets]

8. history filter {none | all | overThreshold | failures}

9. frequency seconds

10. history hours-of-statistics-kept hours

11. history lives-kept lives

12. owner owner-id

13. paths-of-statistics-kept size

14. request-data-size bytes

15. samples-of-history-kept samples

16. history statistics-distribution-interval milliseconds

17. tag text

18. threshold milliseconds

19. timeout milliseconds

20. tos number

21. verify-data

22. vrf vrf-name

23. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ip sla operation-number

Example:

Router(config)# ip sla 10

Begins configuration for an IP SLAs operation and enters IP SLA configuration mode.

Step 4 

path-echo {destination-ip-address | destination-hostname} [source-ip {ip-address | hostname}]

Example:

Router(config-ip-sla)# path-echo 172.29.139.134

Defines a Path Echo operation and enters IP SLA Path Echo configuration mode.

Step 5 

history buckets-kept size

Example:

Router(config-ip-sla-pathEcho)# history buckets-kept 25

(Optional) Sets the number of history buckets that are kept during the lifetime of an IP SLAs operation.

Step 6 

history distributions-of-statistics-kept size

Example:

Router(config-ip-sla-pathEcho)# history distributions-of-statistics-kept 5

(Optional) Sets the number of statistics distributions kept per hop during an IP SLAs operation.

Step 7 

history enhanced [interval seconds] [buckets number-of-buckets]

Example:

Router(config-ip-sla-pathEcho)# history enhanced interval 900 buckets 100

(Optional) Enables enhanced history gathering for an IP SLAs operation.

Step 8 

history filter {none | all | overThreshold | failures}

Example:

Router(config-ip-sla-pathEcho)# history filter failures

(Optional) Defines the type of information kept in the history table for an IP SLAs operation.

Step 9 

frequency seconds

Example:

Router(config-ip-sla-pathEcho)# frequency 30

(Optional) Sets the rate at which a specified IP SLAs operation repeats.

Step 10 

history hours-of-statistics-kept hours

Example:

Router(config-ip-sla-pathEcho)# history hours-of-statistics-kept 4

(Optional) Sets the number of hours for which statistics are maintained for an IP SLAs operation.

Step 11 

history lives-kept lives

Example:

Router(config-ip-sla-pathEcho)# history lives-kept 5

(Optional) Sets the number of lives maintained in the history table for an IP SLAs operation.

Step 12 

owner owner-id

Example:

Router(config-ip-sla-pathEcho)# owner admin

(Optional) Configures the Simple Network Management Protocol (SNMP) owner of an IP SLAs operation.

Step 13 

paths-of-statistics-kept size

Example:

Router(config-ip-sla-pathEcho)# paths-of-statistics-kept 3

(Optional) Sets the number of paths for which statistics are maintained per hour for an IP SLAs operation.

Step 14 

request-data-size bytes

Example:

Router(config-ip-sla-pathEcho)# request-data-size 64

(Optional) Sets the protocol data size in the payload of an IP SLAs operation's request packet.

Step 15 

samples-of-history-kept samples

Example:

Router(config-ip-sla-pathEcho)# samples-of-history-kept 10

(Optional) Sets the number of entries kept in the history table per bucket for an IP SLAs operation.

Step 16 

history statistics-distribution-interval milliseconds

Example:

Router(config-ip-sla-pathEcho)# history statistics-distribution-interval 10

(Optional) Sets the time interval for each statistics distribution kept for an IP SLAs operation.

Step 17 

tag text

Example:

Router(config-ip-sla-pathEcho)# tag TelnetPollServer1

(Optional) Creates a user-specified identifier for an IP SLAs operation.

Step 18 

threshold milliseconds

Example:

Router(config-ip-sla-pathEcho)# threshold 10000

(Optional) Sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation.

Step 19 

timeout milliseconds

Example:

Router(config-ip-sla-pathEcho)# timeout 10000

(Optional) Sets the amount of time an IP SLAs operation waits for a response from its request packet.

Step 20 

tos number

Example:

Router(config-ip-sla-pathEcho)# tos 160

(Optional) Defines a type of service (ToS) byte in the IP header of an IP SLAs operation.

Step 21 

verify-data

Example:

Router(config-ip-sla-pathEcho)# verify-data

(Optional) Causes an IP SLAs operation to check each reply packet for data corruption.

Step 22 

vrf vrf-name

Example:

Router(config-ip-sla-pathEcho)# vrf vpn-A

(Optional) Allows monitoring within Multiprotocol Label Switching (MPLS) Virtual Private Networks (VPNs) using IP SLAs operations.

Step 23 

end

Example:

Router(config-ip-sla-pathEcho)# end

Exits to privileged EXEC mode.

Scheduling IP SLAs Operations

SUMMARY STEPS

1. enable

2. configure terminal

For individual IP SLAs operations only:

3. ip sla schedule operation-number [life {forever | seconds}] [start-time {hh:mm[:ss] [month day | day month] | pending | now | after hh:mm:ss}] [ageout seconds] [recurring]

For multioperation scheduler only:

4. ip sla group schedule group-operation-number operation-id-numbers schedule-period schedule-period-range [ageout seconds] [frequency group-operation-frequency] [life {forever | seconds}] [start-time {hh:mm[:ss] [month day | day month] | pending | now | after hh:mm:ss}]

5. exit

6. show ip sla group schedule

7. show ip sla configuration

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ip sla schedule operation-number [life {forever | seconds}] [start-time {hh:mm[:ss] [month day | day month] | pending | now | after hh:mm:ss}] [ageout seconds] [recurring]

Example:

Router(config)# ip sla schedule 7 start-time now life forever

For individual IP SLAs operations only:

Configures the scheduling parameters for an individual IP SLAs operation.

Step 4 

ip sla group schedule group-operation-number 
operation-id-numbers 
schedule-period schedule-period-range [ageout  
seconds] [frequency group-operation-frequency] 
[life {foreverseconds}] 
[start-time {hh:mm[:ss] 
[month day | day month] | pending | now | 
after hh:mm:ss}]
Example:

Router(config)# ip sla group schedule 1 3,4,6-9

For multioperation scheduler only:

Specifies an IP SLAs operation group number and the range of operation numbers to be scheduled in global configuration mode.

The frequency of all operations scheduled in the operation group should be the same.

The operation ID numbers are limited to a maximum of 125 characters. Do not use large integer values as operation ID numbers.

Step 5 

exit

Example:

Router(config)# exit

Exits to privileged EXEC mode.

Step 6 

show ip sla group schedule

Example:
Router# show ip sla group schedule

(Optional) Displays the IP SLAs group schedule details.

Step 7 

show ip sla configuration
Example:
Router# show ip sla configuration

(Optional) Displays the IP SLAs configuration details.

Examples

The following sample output shows the configuration of all the IP SLAs parameters (including defaults) for the ICMP Path Echo operation number 7.

Router# show ip sla configuration 7

Complete configuration Table (includes defaults)
Entry number: 7
Owner: jdoe
Tag: SGN-RO
Type of operation to perform: pathEcho
Target address: 172.29.139.134
Source address: 172.29.139.132
Request size (ARR data portion): 28
Operation timeout (milliseconds): 1000
Type Of Service parameters: 256
Verify data: No
Loose Source Routing: Disabled
Vrf Name: 
LSR Path:
Operation frequency (seconds): 30
Next Scheduled Start Time: Start Time already passed
Group Scheduled: FALSE
Life (seconds): 300
Entry Ageout (seconds): never
Recurring (Starting Everyday): FALSE
Status of entry (SNMP RowStatus): Active
Threshold (milliseconds): 5000
Number of statistic hours kept: 2
Number of statistic paths kept: 5
Number of statistic hops kept: 16
Number of statistic distribution buckets kept: 1
Statistic distribution interval (milliseconds): 20
Number of history Lives kept: 0
Number of history Buckets kept: 15
Number of history Samples kept: 16
History Filter Type: None

Troubleshooting Tips

If the IP SLAs operation is not running and generating statistics, add the verify-data command to the configuration of the operation (while configuring in IP SLA configuration mode) to enable data verification. When enabled, each operation response is checked for corruption. Use the verify-data command with caution during normal operations because it generates unnecessary overhead.

Use the debug ip sla trace and debug ip sla error commands to help troubleshoot issues with an IP SLAs operation.

What to Do Next

To add proactive threshold conditions and reactive triggering for generating traps, or for starting another operation, to an IP SLAs operation, see Configuring Proactive Threshold Monitoring.

To view and interpret the results of an IP SLAs operation use the show ip sla statistics command. Checking the output for fields that correspond to criteria in your service level agreement will help you determine whether the service metrics are acceptable.

Configuration Examples for IP SLAs ICMP Path Echo Operations

Example: Configuring an ICMP Path Echo Operation

Example: Configuring an ICMP Path Echo Operation

The following example shows how to configure an IP SLAs operation type of ICMP Path Echo that will start after 30 seconds and run for 5 minutes. Figure 2 depicts the ICMP Path Echo operation.

Figure 2 ICMP Path Echo Operation

This example sets a Path Echo operation (ip sla 3) from Router B to Router A using IP/ICMP. The operation attempts to execute three times in 25 seconds (first attempt at 0 seconds).

Router B Configuration

ip sla 3
 path-echo 172.29.139.134
 frequency 10
 tag SGN-RO
 timeout 1000
ip sla schedule 3 life 25

Additional References

Related Documents

Related Topic
Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Cisco IOS IP SLAs commands

Cisco IOS IP SLAs Command Reference

Cisco IOS IP SLAs: general information

"Cisco IOS IP SLAs Overview" chapter of the Cisco IP SLAs Configuration Guide.


Standards

Standards
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIBs
MIBs Link

CISCO-RTTMON-MIB

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFCs
Title

RFC 862

Echo Protocol


Technical Assistance

Description
Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html


Feature Information for IP SLAs ICMP Path Echo Operations

Table 1 lists the features in this module and provides links to specific configuration information.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 1 Feature Information for IP SLAs ICMP Path Echo Operations 

Feature Name
Releases
Feature Information

IP SLAs ICMP Path Echo Operation

12.2(31)SB2
12.2(33)SRB1
12.2(33)SXH
12.3(14)T
15.0(1)S
Cisco IOS XE 3.1.0SG

The Cisco IOS IP SLAs Internet Control Message Protocol (ICMP) path echo operation allows you to measure end-to-end and hop-by-hop network response time between a Cisco device and other devices using IP.