This documentation has been moved
Implementing IPv6 over MPLS
Downloads: This chapterpdf (PDF - 243.0KB) | Feedback

Implementing IPv6 over MPLS

Table Of Contents

Implementing IPv6 over MPLS

Finding Feature Information

Contents

Prerequisites for Implementing IPv6 over MPLS

Information About Implementing IPv6 over MPLS

Benefits of Deploying IPv6 over MPLS Backbones

IPv6 on the Provider Edge Routers (6PE)

6PE Multipath

How to Implement IPv6 over MPLS

Deploying IPv6 on the Provider Edge Routers (6PE)

Specifying the Source Address Interface on a 6PE Router

Prerequisites

Restrictions

Binding and Advertising the 6PE Label to Advertise Prefixes

Configuring iBGP Multipath Load Sharing

Verifying 6PE Configuration and Operation

Output Examples

Configuration Examples for IPv6 over MPLS

Example: Provider Edge Router

Example: Core Router

Additional References

Related Documents

MIBs

RFCs

Technical Assistance

Feature Information for Implementing IPv6 over MPLS


Implementing IPv6 over MPLS


First Published: July 30, 2010
Last Updated: July 30, 2010

Multiprotocol Label Switching (MPLS) is deployed by many service providers in their IPv4 networks. Service providers want to introduce IPv6 services to their customers, but changes to their existing IPv4 infrastructure can be expensive and the cost benefit for a small amount of IPv6 traffic does not make economic sense. Several integration scenarios have been developed to leverage an existing IPv4 MPLS infrastructure and add IPv6 services without requiring any changes to the network backbone. This document describes how to implement IPv6 over MPLS.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Implementing IPv6 over MPLS" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

Prerequisites for Implementing IPv6 over MPLS

Information About Implementing IPv6 over MPLS

How to Implement IPv6 over MPLS

Configuration Examples for IPv6 over MPLS

Additional References

Feature Information for Implementing IPv6 over MPLS

Prerequisites for Implementing IPv6 over MPLS

This module assumes that you are familiar with IPv4. Refer to the publications referenced in the "Related Documents" section for IPv4 configuration and command reference information.

Before the IPv6 Provider Edge Router over MPLS (6PE) feature can be implemented, MPLS must be running over the core IPv4 network. If Cisco routers are used, Cisco Express Forwarding or distributed Cisco Express Forwarding must be enabled for both IPv4 and IPv6 protocols. This module assumes that you are familiar with MPLS.

Information About Implementing IPv6 over MPLS

Benefits of Deploying IPv6 over MPLS Backbones

IPv6 on the Provider Edge Routers (6PE)

Benefits of Deploying IPv6 over MPLS Backbones

IPv6 over MPLS backbones enables isolated IPv6 domains to communicate with each other over an MPLS IPv4 core network. This implementation requires only a few backbone infrastructure upgrades and no reconfiguration of core routers because forwarding is based on labels rather than the IP header itself, providing a very cost-effective strategy for the deployment of IPv6.

Additionally, the inherent Virtual Private Network (VPN) and MPLS traffic engineering (MPLS-TE) services available within an MPLS environment allow IPv6 networks to be combined into IPv4 VPNs or extranets over an infrastructure supporting IPv4 VPNs and MPLS-TE.

Refer to Implementing Tunneling for IPv6 for configuration information on manually configured tunnels, automatic tunnels, and 6to4 tunnels.

Limitations on using tunnels involve the manual configuring of a mesh of tunnels on the CE routers, creating scaling issues for large networks.

IPv6 on the Provider Edge Routers (6PE)

The Cisco implementation of IPv6 provider edge router over MPLS is called 6PE, and it enables IPv6 sites to communicate with each other over an MPLS IPv4 core network using MPLS label switched paths (LSPs). This feature relies on multiprotocol Border Gateway Protocol (BGP) extensions in the IPv4 network configuration on the provider edge (PE) router to exchange IPv6 reachability information in addition to an MPLS label for each IPv6 address prefix to be advertised. Edge routers are configured to be dual stack running both IPv4 and IPv6, and use the IPv4 mapped IPv6 address for IPv6 prefix reachability exchange.

A hierarchy of labels is imposed on the 6PE ingress router to keep the IPv6 traffic transparent to all the core routers. The top label provides connectivity inside the IPv4 MPLS core network and the label is distributed by Label Distribution Protocol (LDP), Tag Distribution Protocol (TDP), or Resource Reservation Protocol (RSVP). TDP and LDP can both be used for label distribution, but RSVP is used only in the context of MPLS-TE label exchange. The bottom label, automatically assigned to the IPv6 prefix of the destination, is distributed by multiprotocol BGP and used at each 6PE egress router for IPv6 forwarding.

In Figure 21, the 6PE routers are configured as dual stack routers able to route both IPv4 and IPv6 traffic. Each 6PE router is configured to run LDP, TDP, or RSVP (if traffic engineering is configured) to bind the IPv4 labels. The 6PE routers use multiprotocol BGP to exchange reachability information with the other 6PE devices within the MPLS domain, and to distribute aggregate IPv6 labels between them. All 6PE and core routers—P routers in Figure 3—within the MPLS domain share a common IPv4 Interior Gateway Protocol (IGP) such as Open Shortest Path First (OSPF) or Integrated Intermediate System-to-Intermediate System (IS-IS).

Figure 21 6PE Router Topology

The interfaces on the 6PE routers connecting to the CE router can be configured to forward IPv6 traffic, IPv4 traffic, or both types of traffic depending on the customer requirements. 6PE routers advertise IPv6 reachability information learned from their 6PE peers over the MPLS cloud. Service providers can delegate an IPv6 prefix from their registered IPv6 prefixes over the 6PE infrastructure; otherwise, there is no impact on the CE router.

The P routers in the core of the network are not aware that they are switching IPv6 packets. Core routers are configured to support MPLS and the same IPv4 IGP as the PE routers to establish internal reachability inside the MPLS cloud. Core routers also use LDP, TDP, or RSVP for binding IPv4 labels. Implementing the Cisco 6PE feature does not have any impact on the MPLS core devices.

Within the MPLS network, IPv6 traffic is forwarded using label switching, making the IPv6 traffic transparent to the core of the MPLS network. No IPv6 over IPv4 tunnels or Layer 2 encapsulation methods are required.

6PE Multipath

Internal and external Border Gateway Protocol (BGP) multipath for IPv6 allows the IPv6 router to load balance between several paths (for example, same neighboring autonomous system [AS] or sub-AS, or the same metric) to reach its destination. The 6PE multipath feature uses multiprotocol internal BGP (MP-iBGP) to distribute IPv6 routes over the MPLS IPv4 core network and to attach an MPLS label to each route.

When MP-iBGP multipath is enabled on the 6PE router, all labeled paths are installed in the forwarding table with MPLS information (label stack) when MPLS information is available. This functionality enables 6PE to perform load balancing.

How to Implement IPv6 over MPLS

Deploying IPv6 on the Provider Edge Routers (6PE)

Configuring iBGP Multipath Load Sharing

Verifying 6PE Configuration and Operation

Deploying IPv6 on the Provider Edge Routers (6PE)

Specifying the Source Address Interface on a 6PE Router

Binding and Advertising the 6PE Label to Advertise Prefixes

Specifying the Source Address Interface on a 6PE Router

Two configuration tasks using the network shown in Figure 22 are required at the 6PE1 router to enable the 6PE feature.

The customer edge router—CE1 in Figure 22—is configured to forward its IPv6 traffic to the 6PE1 router. The P1 router in the core of the network is assumed to be running MPLS, a label distribution protocol, an IPv4 IGP, and Cisco Express Forwarding or distributed Cisco Express Forwarding, and does not require any new configuration to enable the 6PE feature.

Figure 22 6PE Configuration Example

Prerequisites

The 6PE routers—the 6PE1 and 6PE2 routers in Figure 22—must be members of the core IPv4 network. The 6PE router interfaces attached to the core network must be running MPLS, the same label distribution protocol, and the same IPv4 IGP, as in the core network.

The 6PE routers must also be configured to be dual stack to run both IPv4 and IPv6.

Restrictions

The following restrictions apply when implementing the IPv6 Provider Edge Router over MPLS (6PE) feature:

Core MPLS routers are supporting MPLS and IPv4 only, so they cannot forward or create any IPv6 Internet Control Message Protocol (ICMP) messages.

Load balancing ability is not provided by Cisco 6PE between an MPLS path and an IPv6 path. If both are available, the MPLS path is always preferred. Load balancing between two MPLS paths is possible.

BGP multipath is not supported for Cisco 6PE routes. If two BGP peers advertise the same prefix with an equal cost, Cisco 6PE will use the last route to cross the MPLS core.

6PE feature is not supported over tunnels other than RSVP-TE tunnels.

Perform this task to specify the interface from which locally generated packets take their source IPv6 address.

SUMMARY STEPS

1. enable

2. configure terminal

3. ipv6 unicast-routing

4. ipv6 cef

5. interface type number

6. ipv6 address {ipv6-address/prefix-length | prefix-name sub-bits/prefix-length}

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ipv6 unicast-routing

Example:

Router(config)# ipv6 unicast-routing

Enables the forwarding of IPv6 unicast datagrams.

Step 4 

ipv6 cef

Example:

Router(config)# ipv6 cef

Enables IPv6 Cisco Express Forwarding.

Step 5 

interface type number

Example:

Router(config)# interface GigabitEthernet 0/0/0

Specifies an interface type and number and enters interface configuration mode.

In the context of this feature, the interface to be configured is the interface communicating with the CE router.

Step 6 

ipv6 address {ipv6-address/prefix-length | prefix-name sub-bits/prefix-length}

Example:

Router(config-if)# ipv6 address 2001:DB8:FFFF::2/64

Configures an IPv6 address based on an IPv6 general prefix and enable IPv6 processing on an interface.


Binding and Advertising the 6PE Label to Advertise Prefixes

Perform this task to enable the binding and advertising of aggregate labels when advertising IPv6 prefixes to a specified BGP neighbor.

SUMMARY STEPS

1. enable

2. configure terminal

3. router bgp as-number

4. no bgp default ipv4-unicast

5. neighbor {ip-address | ipv6-address | peer-group-name} remote-as as-number

6. neighbor {ip-address | ipv6-address | peer-group-name} update-source interface-type interface-number

7. address-family ipv6 [unicast]

8. neighbor {ip-address | peer-group-name | ipv6-address} activate

9. neighbor {ip-address | ipv6-address} send-label

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

router bgp as-number

Example:

Router(config)# router bgp 65000

Enters router configuration mode for the specified routing process.

Step 4 

no bgp default ipv4-unicast

Example:

Router(config-router)# no bgp default ipv4-unicast

Disables the IPv4 unicast address family for the BGP routing process specified in the previous step.

Note Routing information for the IPv4 unicast address family is advertised by default for each BGP routing session configured with the neighbor remote-as command unless you configure the no bgp default ipv4-unicast command before configuring the neighbor remote-as command.

Step 5 

neighbor {ip-address | ipv6-address | peer-group-name} remote-as as-number

Example:

Router(config-router)# neighbor 192.168.99.70 remote-as 65000

Adds the IP address of the neighbor in the specified autonomous system to the BGP neighbor table of the local router.

Step 6 

neighbor {ip-address | ipv6-address | peer-group-name} update-source interface-type interface-number

Example:

Router(config-router)# neighbor 192.168.99.70 update-source Loopback 0

Specifies the interface whose IPv4 address is to be used as the source address for the peering.

In the context of this task, the interface must have an IPv4 address with a 32-bit mask configured. Use of a loopback interface is recommended. This address is used to determine the IPv6 next hop by the peer 6PE.

Step 7 

address-family ipv6 [unicast]

Example:

Router(config-router)# address-family ipv6

Specifies the IPv6 address family and enters address family configuration mode.

The unicast keyword specifies the IPv6 unicast address family. By default, the router is placed in configuration mode for the IPv6 unicast address family if the unicast keyword is not specified with the address-family ipv6 command.

Step 8 

neighbor {ip-address | peer-group-name | ipv6-address} activate

Example:

Router(config-router-af)# neighbor 192.168.99.70 activate

Enables the neighbor to exchange prefixes for the IPv6 address family with the local router.

Step 9 

neighbor {ip-address | ipv6-address} send-label

Example:

Router(config-router-af)# neighbor 192.168.99.70 send-label

Advertises the capability of the router to send MPLS labels with BGP routes.

In IPv6 address family configuration mode this command enables binding and advertisement of aggregate labels when advertising IPv6 prefixes in BGP.


Configuring iBGP Multipath Load Sharing

Perform this task to configure iBGP multipath load sharing and control the maximum number of parallel iBGP routes that can be installed in a routing table.

SUMMARY STEPS

1. enable

2. configure terminal

3. router bgp as-number

4. maximum-paths ibgp number-of-paths

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

router bgp as-number

Example:

Router(config)# router bgp 65000

Enters router configuration mode for the specified routing process.

Step 4 

maximum-paths ibgp number-of-paths

Example:

Router(config-router)# maximum-paths ibgp 3

Controls the maximum number of parallel iBGP routes that can be installed in a routing table.


Verifying 6PE Configuration and Operation

SUMMARY STEPS

1. show bgp ipv6 {unicast | multicast} [ipv6-prefix/prefix-length] [longer-prefixes] [labels]

2. show bgp ipv6 {unicast | multicast} neighbors [ipv6-address] [received-routes | routes | flap-statistics | advertised-routes | paths regular-expression | dampened-routes]

3. show mpls forwarding-table [network {mask | length} | labels label [-label] | interface interface | next-hop address | lsp-tunnel [tunnel-id]] [vrf vrf-name] [detail]

4. show ipv6 cef [ipv6-prefix/prefix-length] | [interface-type interface-number] [longer-prefixes | similar-prefixes | detail | internal | platform | epoch | source]]

5. show ipv6 route [ipv6-address | ipv6-prefix/prefix-length | protocol | interface-type interface-number]

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

show bgp ipv6 {unicast | multicast} [ipv6-prefix/prefix-length] [longer-prefixes] [labels]

Example:

Router> show bgp ipv6 unicast 2001:DB8:DDDD::/48

(Optional) Displays entries in the IPv6 BGP routing table.

In this example, information about the IPv6 route for the prefix 2001:DB8:DDDD::/48 is displayed.

Step 2 

show bgp ipv6 {unicast | multicast} neighbors [ipv6-address] [received-routes | routes | flap-statistics | advertised-routes | paths regular-expression | dampened-routes]

Example:

Router> show bgp ipv6 neighbors unicast 192.168.99.70

(Optional) Displays information about IPv6 BGP connections to neighbors.

In this example, information including the IPv6 label capability is displayed for the BGP peer at 192.168.99.70.

Step 3 

show mpls forwarding-table [network {mask | length} | labels label [-label] | interface interface | nexthop address | lsp-tunnel [tunnel-id]] [vrf vrf-name] [detail]

Example:

Router> show mpls forwarding-table

(Optional) Displays the contents of the MPLS Forwarding Information Base (FIB).

In this example, information linking the MPLS label with IPv6 prefixes is displayed where the labels are shown as aggregate and the prefix is shown as IPv6.

Step 4 

show ipv6 cef [ipv6-prefix/prefix-length] | [interface-type interface-number] [longer-prefixes | similar-prefixes | detail | internal | platform | epoch | source]]

Example:

Router> show ipv6 cef 2001:DB8:DDDD::/64

(Optional) Displays FIB entries based on IPv6 address information.

In this example, label information from the Cisco Express Forwarding table for prefix 2001:DB8:DDDD::/64 is displayed.

Step 5 

show ipv6 route [ipv6-address | ipv6-prefix/prefix-length | protocol | interface-type interface-number]

Example:

Router> show ipv6 route

(Optional) Displays the current contents of the IPv6 routing table.


Output Examples

Sample Output from the show bgp ipv6 Command

Sample Output from the show bgp ipv6 neighbors Command

Sample Output from the show mpls forwarding-table Command

Sample Output from the show bgp ipv6 Command

Sample Output from the show ipv6 cef Command

Sample Output from the show ipv6 route Command

Sample Output from the show bgp ipv6 Command

In the following example, output information about an IPv6 route is displayed using the show bgp ipv6 command with an IPv6 prefix:

Router# show bgp ipv6 2001:DB8:DDDD::/48

BGP routing table entry for 2001:DB8:DDDD::/48, version 15
Paths: (1 available, best #1, table Global-IPv6-Table)
  Not advertised to any peer
  Local
    ::FFFF:192.168.99.70 (metric 20) from 192.168.99.70 (192.168.99.70)
      Origin IGP, localpref 100, valid, internal, best

Sample Output from the show bgp ipv6 neighbors Command

In the following example, output information about a BGP peer including the "IPv6 label" capability is displayed using the show bgp ipv6 neighbors command with an IP address:

Router# show bgp ipv6 neighbors 192.168.99.70

BGP neighbor is 192.168.99.70, remote AS 65000, internal link
  BGP version 4, remote router ID 192.168.99.70
  BGP state = Established, up for 00:05:17
  Last read 00:00:09, hold time is 0, keepalive interval is 60 seconds
  Neighbor capabilities:
    Route refresh: advertised and received
    Address family IPv6 Unicast: advertised and received
    ipv6 MPLS Label capability: advertised and received
  Received 54 messages, 0 notifications, 0 in queue
  Sent 55 messages, 1 notifications, 0 in queue
  Default minimum time between advertisement runs is 5 seconds

 For address family: IPv6 Unicast
  BGP table version 21880, neighbor version 21880
  Index 1, Offset 0, Mask 0x2
  Route refresh request: received 0, sent 0
  77 accepted prefixes consume 4928 bytes 
  Prefix advertised 4303, suppressed 0, withdrawn 1328
  Number of NLRIs in the update sent: max 1, min 0

Sample Output from the show mpls forwarding-table Command

In the following example, output information linking the MPLS label with prefixes is displayed using the show mpls forwarding-table command. If the 6PE feature is configured, the labels are aggregated because there are several prefixes for one local label, and the prefix column contains "IPv6" instead of a target prefix.

Router# show mpls forwarding-table

Local Outgoing      Prefix            Bytes tag Outgoing       Next Hop       
tag   tag or VC     or Tunnel Id      switched  interface                     
16    Aggregate     IPv6              0             
17    Aggregate     IPv6              0                 
18    Aggregate     IPv6              0                 
19    Pop tag       192.168.99.64/30  0         GE0/0         point2point    
20    Pop tag       192.168.99.70/32  0         GE0/0         point2point      
21    Pop tag       192.168.99.200/32 0         GE0/0         point2point    
22    Aggregate     IPv6              5424    
23    Aggregate     IPv6              3576 
24    Aggregate     IPv6              2600

Sample Output from the show bgp ipv6 Command

In the following example, output information about the top of the stack label with label switching information is displayed using the show bgp ipv6 command with the labels keyword:

Router# show bgp ipv6 labels

Network              Next Hop               In tag/Out tag
2001:DB8:DDDD::/64  ::FFFF:192.168.99.70   notag/20

Sample Output from the show ipv6 cef Command

In the following example, output information about labels from the Cisco Express Forwarding table is displayed using the show ipv6 cef command with an IPv6 prefix:

Router# show ipv6 cef 2001:DB8:DDDD::/64

2001:DB8:DDDD::/64
      nexthop ::FFFF:192.168.99.70
      fast tag rewrite with Se0/0, point2point, tags imposed {19 20}

Sample Output from the show ipv6 route Command

In the following example, output information from the IPv6 routing table is displayed using the show ipv6 route command. The output shows the IPv6 MPLS virtual interface as the output interface of IPv6 routes forwarded across the MPLS cloud. This example shows output from the 6PE1 router.

The 6PE2 router has advertised the IPv6 prefix of 2001:DB8:dddd::/48 configured for the CE2 router and the next-hop address is the IPv4-compatible IPv6 address ::ffff:192.168.99.70, where 192.168.99.70 is the IPv4 address of the 6PE2 router.

Router# show ipv6 route

IPv6 Routing Table - 10 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
B 2001:DB8:DDDD::/64 [200/0]
  via ::FFFF:192.168.99.70, IPv6-mpls
B 2001:DB8:DDDD::/64 [200/0]
  via ::FFFF:192.168.99.70, IPv6-mpls
L 2001:DB8:FFFF::1/128 [0/0]
  via ::, GigabitEthernet0/0/0
C 2001:DB8:FFFF::/64 [0/0]
  via ::, GigabitEthernet0/0/0
S 2001:DB8:FFFF::/48 [1/0]
  via 2001:DB8:B00:FFFF::2, GigabitEthernet0/0/0

Configuration Examples for IPv6 over MPLS

The following examples show 6PE configuration examples.

Example: Provider Edge Router

Example: Core Router

Example: Provider Edge Router

The 6PE router is configured for both IPv4 and IPv6 traffic. GigabitEthernet interface 0/0/0 is configured with an IPv4 address and is connected to a router in the core of the network. Integrated IS-IS and TDP configurations on this router are similar to the P1 router.

Router 6PE1 exchanges IPv6 routing information with another 6PE router using internal BGP (iBGP) established over an IPv4 connection so that all the neighbor commands use the IPv4 address of the 6PE2 router. All the BGP peers are within autonomous system 65000, so synchronization with IGP is turned off for IPv4. In IPv6 address family configuration mode, synchronization is disabled by default.

IPv6 and Cisco Express Forwarding for IPv6 are enabled, the 6PE2 neighbor is activated, and aggregate label binding and advertisement is enabled for IPv6 prefixes using the neighbor send-label command. Connected and static IPV6 routes are redistributed using BGP. If IPv6 packets are generated in the local router, the IPv6 address for MPLS processing will be the address of loopback interface 0.

In the following example, serial interface 0/0 connects to the customer and the IPv6 prefix delegated to the customer is 2001:DB8:ffff::/48, which is determined from the service provider IPv6 prefix. A static route is configured to route IPv6 packets between the 6PE route and the CE router.

ip cef
ipv6 cef
ipv6 unicast-routing
!
mpls ipv6 source-interface Loopback0
tag-switching tdp router-id Loopback0
!
interface Loopback0
 ip address 192.168.99.5 255.255.255.255
 ipv6 address 2001:DB8:1000:1::1/64
!
interface GigabitEthernet0/0/0
 description to_P_router
 ip address 192.168.99.1 255.255.255.252
 ip router isis 
 tag-switching ip
!
interface GigabitEthernet0/1/0
 description to_CE_router
 no ip address
 ipv6 address 2001:DB8:FFFF::1/64
!
router isis 
 passive-interface Loopback0
 net 49.0001.1921.6809.9005.00
!
router bgp 65000
 no bgp default ipv4-unicast
 bgp log-neighbor-changes
 neighbor 192.168.99.70 remote-as 65000
 neighbor 192.168.99.70 description to_6PE2
 neighbor 192.168.99.70 update-source Loopback0
 !
 address-family ipv6
 neighbor 192.168.99.70 activate
 neighbor 192.168.99.70 send-label
 network 2001:DB8:FFFF::/48
 exit-address-family
!
ipv6 route 2001:DB8:FFFF::/48 GigabitEthernet0/0/0 2001:DB8:FFFF::2

Example: Core Router

In the following example, the router in the core of the network is running MPLS, IS-IS, and IPv4 only. The GigabitEthernet interfaces are configured with IPv4 address and are connected to the 6PE routers. IS-IS is the IGP for this network and the P1 and 6PE routers are in the same IS-IS area 49.0001. TDP and tag switching are enabled on both the GigabitEthernet interfaces. Cisco Express Forwarding is enabled in global configuration mode.

ip cef
!
tag-switching tdp router-id Loopback0
!
interface Loopback0
 ip address 192.168.99.200 255.255.255.255
!
interface GigabitEthernet0/0/0
 description to_6PE1
 ip address 192.168.99.2 255.255.255.252
 ip router isis 
 tag-switching ip
!
interface GigabitEthernet0/1/0
 description to_6PE2
 ip address 192.168.99.66 255.255.255.252
 ip router isis 
 tag-switching ip

router isis 
 passive-interface Loopback0
 net 49.0001.1921.6809.9200.00

Additional References

Related Documents

Related Topic
Document Title

IPv6 supported feature list

"Start Here: Cisco IOS XE Software Release Specifics for IPv6 Features," Cisco IOS XE IPv6 Configuration Guide

IPv6 commands: complete command syntax, command mode, defaults, usage guidelines, and examples

Cisco IOS IPv6 Command Reference

Cisco IOS master command list, all  releases

Cisco IOS Master Command List, All Releases


MIBs

MIBs
MIBs Link

None

To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFCs
Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.


Technical Assistance

Description
Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html


Feature Information for Implementing IPv6 over MPLS

Table 8 lists the features in this module and provides links to specific configuration information.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 8 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 8 Feature Information for Implementing IPv6 over MPLS 

Feature Name
Releases
Feature Information

IPv6 Switching—Provider Edge Router over MPLS (6PE)

Cisco IOS XE Release 3.1S

The Cisco implementation of IPv6 provider edge router over MPLS enables IPv6 sites to communicate with each other over an MPLS IPv4 core network using MPLS LSPs.

The following sections provide information about this feature:

IPv6 on the Provider Edge Routers (6PE)

Deploying IPv6 on the Provider Edge Routers (6PE)

SUMMARY STEPS

Binding and Advertising the 6PE Label to Advertise Prefixes

Configuration Examples for IPv6 over MPLS

The following commands were modified for this release: ipv6 cef, neighbor activate, neighbor remote-as, neighbor send-label, neighbor update-source, router bgp, show bgp ipv6, show bgp ipv6 neighbors, show ipv6 cef, show ipv6 route, show mpls forwarding-table.

6PE Multipath

Cisco IOS XE Release 3.1S

The 6PE multipath feature uses multiprotocol internal BGP (MP-iBGP) to distribute IPv6 routes over the MPLS IPv4 core network and to attach an MPLS label to each route.

The following sections provide information about this feature:

6PE Multipath

Configuring iBGP Multipath Load Sharing

The following commands were modified for this release: maximum-paths ibgp.