DHCP Relay Server ID Override and Link Selection Option 82 Suboptions
ErrorMessage : Error while constructing the Hinav

null
Downloads: This chapterpdf (PDF - 196.0KB) | Feedback

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Table Of Contents

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Finding Feature Information

Contents

Restrictions for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Information About DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Server ID Override Suboption

Link Selection Suboption

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions Feature Design

How to Configure Support for the DHCP Relay Server ID Override and Link Selection Suboptions

Configuring the DHCP Relay Agent to Insert the DHCP Server ID Override and Link Selection Suboptions into Option 82

Restrictions

Configuration Examples for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Glossary


DHCP Relay Server ID Override and Link Selection Option 82 Suboptions


First Published: December 10, 2007
Last Updated: May 4, 2009

The DHCP Relay Server ID Override and Link Selection Option 82 Suboptions feature enables the relay agent to be part of all DHCP message exchanges by supporting the use of two suboptions of the relay agent information option (option 82). This design allows DHCPv4 to operate in networks where direct communication between the client and server is not possible or desired. When used together, these two suboptions enable the deployment of an architecture where it is desirable to have all DHCP traffic flow through the relay agent, allowing for greater control of DHCP communications.

This feature also introduces the capability to manually configure the interface for the relay agent to use as the source IP address for messages relayed to the DHCP server. This configuration allows the network administrator to specify a stable, hardware-independent IP address (such as a loopback interface).

Finding Feature Information

For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

Restrictions for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Information About DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

How to Configure Support for the DHCP Relay Server ID Override and Link Selection Suboptions

Configuration Examples for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Additional References

Feature Information for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Glossary

Restrictions for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

If this feature and the DHCP Relay MPLS VPN Support feature are both configured, DHCP Relay MPLS VPN Support takes precedence.

Information About DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

To configure the DHCP Relay Server ID Override and Link Selection Option 82 Suboptions feature, you should understand the following concepts:

Server ID Override Suboption

Link Selection Suboption

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions Feature Design

Server ID Override Suboption

The server identifier (ID) override suboption allows the DHCP relay agent to specify a new value for the server ID option, which is inserted by the DHCP server in the reply packet. This suboption allows the DHCP relay agent to act as the actual DHCP server such that the renew requests will come to the relay agent rather than the DHCP server directly. The server ID override suboption contains the incoming interface IP address, which is the IP address on the relay agent that is accessible from the client. Using this information, the DHCP client sends all renew and release request packets to the relay agent. The relay agent adds all of the appropriate suboptions and then forwards the renew and release request packets to the original DHCP server.

Link Selection Suboption

The link selection suboption provides a mechanism to separate the subnet/link on which the DHCP client resides from the the gateway address (giaddr), which can be used to communicate with the relay agent by the DHCP server. The relay agent will set the suboption to the correct subscriber subnet and the DHCP server will use that value to assign an IP address rather than the giaddr value. The relay agent will set the giaddr to its own IP address so that DHCP messages are routable over the network.

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions Feature Design

The current DHCP IPv4 deployment model assumes a single routing domain between the DHCP client and DHCP server. In some network designs, the DHCP server can not directly communicate with DHCP clients. Customers may choose this design to make critical infrastructure servers inaccessible and to protect the DHCP server from client attacks.

Relay agents are used to forward requests and replies between clients and servers when they are not on the same physical subnet. In all cases, the DHCP relay agent must be able to communicate directly with both the DHCP server and DHCP client. By using the relay agent information option (option 82), the DHCP relay agent can include additional information about itself when forwarding client-originated DHCP packets to a DHCP server.

The DHCP Relay Server ID Override and Link Selection Option 82 Suboptions feature enables the relay agent to be part of all DHCP message exchanges by supporting the use of two suboptions of option 82: server ID override and link selection suboptions. This design results in all DHCP messages flowing through the relay agent, allowing for greater control of DHCP communications.

Communication from the DHCP server through the relay agent can also be an issue. If the server needs to reach the client, it must do so through the relay agent. The IP address of the relay agent might not be ideal. For example, if the network is renumbered or if the interface at the relay agent is down for some reason, the server may not be able to reach the client. This feature introduces the capability to manually configure the interface for the relay agent to use as the source IP address for messages relayed to the DHCP server. This configuration allows the network administrator to specify a stable, hardware-independent IP address (such as a loopback interface).

Figure 1 shows the processing that occurs on the DHCP relay agent and DHCP server when this feature is configured.

Figure 1 DHCP Relay Agent and DHCP Server Processing of Option 82 Suboptions

1. The DHCP client generates a DHCP request and broadcasts it on the network.

2. The DHCP relay agent intercepts the broadcast DHCP request packet and inserts a server ID override suboption and link selection suboption to its relay agent information option in the DHCP packet. The server ID override and link selection suboptions contain the incoming interface IP address, which is the IP address on the relay agent that is accessible from the client (10.1.1.1 in this case).

3. The relay agent sets the giaddr to the IP address of an interface that is reachable by the DHCP server (typically the server-facing interface that will be used to transmit the message, 10.3.1.2 in this case).

4. If the source interface is explicitly configured on a loopback interface (ip dhcp-relay source-interface command), the relay agent will use that address as the source IP address (giaddr) for messages relayed to the DHCP server (10.2.1.1 in this case).

The following processing occurs on the DHCP server after receiving the forwarded packets from the relay agent:

5. The DHCP server uses the link selection suboption to locate the correct address pools for the DHCP client.

6. The DHCP server sets the server ID option to the value specified by the server ID override suboption of the DHCP packet.

7. The DHCP server sends the reply message to the IP address specified in the giaddr.

The DHCP client will see the relay agent address as the server ID and use that address when unicasting RENEW messages.

How to Configure Support for the DHCP Relay Server ID Override and Link Selection Suboptions

This section contains the following procedure:

Configuring the DHCP Relay Agent to Insert the DHCP Server ID Override and Link Selection Suboptions into Option 82

Configuring the DHCP Relay Agent to Insert the DHCP Server ID Override and Link Selection Suboptions into Option 82

To configure this feature, perform the steps below:

Restrictions

If this feature and the DHCP Relay MPLS VPN Support feature are both configured, the DHCP Relay MPLS VPN Support feature takes precedence.

SUMMARY STEPS

1. enable

2. configure terminal

3. ip dhcp-relay information option server-override

4. ip dhcp-relay source-interface type number

5. interface type number

6. ip dhcp relay information option server-id-override

7. ip dhcp relay source-interface type number

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

ip dhcp-relay information option server-override

Example:

Router(config)# ip dhcp-relay information option server-override

Enables the system to globally insert the server ID override and link selection suboptions into the DHCP relay agent information option in forwarded BOOTREQUEST messages to a DHCP server.

If the ip dhcp relay information option server-id-override interface configuration command is configured on an interface, it overrides the global configuration on that interface only.

Step 4 

ip dhcp-relay source-interface type number

Example:

Router(config)# ip dhcp-relay source-interface loopback 0

(Optional) Globally configures the source interface for the relay agent to use as the source IP address for relayed messages.

This command allows the network administrator to specify a stable, hardware-independent IP address (such as a loopback interface).

If the ip dhcp relay source-interface interface configuration command is configured on an interface, it overrides the global configuration on that interface only.

Step 5 

interface type number

Example:

Router(config)# interface GigabitEthernet0/0/0

(Optional) Configures an interface and enters interface configuration mode.

Step 6 

ip dhcp relay information option server-id-override

Example:

Router(config-if)# ip dhcp relay information option server-id-override

(Optional) Enables the system to insert the server ID override and link selection suboptions on a specific interface into the DHCP relay agent information option in forwarded BOOTREQUEST messages to a DHCP server.

Step 7 

ip dhcp relay source-interface type number

Example:

Router(config-if)# ip dhcp relay source-interface loopback 2

(Optional) Configures the source interface for the relay agent to use as the source IP address for relayed messages.

Configuration Examples for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

The section provides the following example:

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions: Example

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions: Example

In the following example, the IP address of the loopback interface is used as the source IP address for relayed messages. The client initiates IP address negotiation from GigabitEthernet interface 0/0/0. The DHCP relay agent is configured globally to insert the server ID override suboption and link selection suboption into the relay agent information option of the DHCP packet. The relay agent uses the server ID override suboption to force the DHCP server to use that value as the server ID in the DHCP message. The DHCP server uses the link selection suboption to determine from which subnet to assign an IP address.

DHCP Client

interface GigabitEthernet0/0/0
 ip address dhcp

DHCP Relay Agent

ip dhcp-relay information option server-override
ip dhcp-relay source-interface loopback0
!
interface Loopback0
 ip address 10.2.1.1 255.255.255.0
!
interface GigabitEthernet0/0/0
 ip address 10.1.1.1 255.255.255.0
 ip helper-address 10.3.1.1
!
interface GigabitEthernet1/0/0
 ip address 10.3.1.2 255.255.255.0

DHCP Server

ip dhcp excluded-address 10.3.0.1
ip dhcp pool pool1
 network 10.1.1.0 255.255.255.0
 lease 0 0 1
!
interface GigabitEthernet0/0/0
 ip address 10.3.1.1 255.255.255.0

Additional References

The following sections provide references related to the DHCP Relay Server ID Override and Link Selection Option 82 Suboptions feature.

Related Documents

Related Topic
Document Title

DHCP conceptual information

"DHCP Overview" module

DHCP server configuration tasks, examples, and conceptual information

"Configuring the Cisco IOS XE DHCP Server" module

DHCP relay agent configuration tasks, examples, and conceptual information

"Configuring the Cisco IOS XE DHCP Relay Agent" module

DHCP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

Cisco IOS IP Addressing Services Command Reference


Standards

Standard
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIB
MIBs Link

No new MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs


Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport


Feature Information for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.


Note Table 1 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.


Table 1 Feature Information for DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Feature Name
Releases
Feature Configuration Information

DHCP Relay Server ID Override and Link Selection Option 82 Suboptions

Cisco IOS XE Release 2.1

This feature enables the relay agent to be part of all DHCP message exchanges by supporting the use of two suboptions of the relay agent information option (option 82). This design allows DHCPv4 to operate in networks where direct communication between the client and server is not possible or desired. When used together, these two suboptions enable the deployment of an architecture where it is desirable to have all DHCP traffic flow through the relay agent, allowing for greater control of DHCP communications.

The following commands were introduced by this feature: ip dhcp-relay information option server-override, ip dhcp relay information option server-id-override, ip dhcp-relay source-interface, and ip dhcp relay source-interface.


Glossary

client—A host trying to configure its interface (obtain an IP address) using DHCP or BOOTP protocols.

DHCP—Dynamic Host Configuration Protocol.

DHCP options and suboptions—Configuration parameters and other control information are carried in tagged data items that are stored in the options field of the DHCP message. Options provide a method of appending additional information. Vendors that want to provide additional information to their client not designed into the protocol can use options.

giaddr—gateway address field of the DHCP packet. The giaddr provides the DHCP server with information about the IP address subnet in which the client resides. The giaddr also provides the DHCP server with an IP address where the DHCP response messages can be sent.

relay agent—A router that forwards DHCP and BOOTP messages between a server and a client on different subnets.


CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.