Cisco Packet Data Serving Node (PDSN) Release 3.5 for Cisco IOS Release 12.4(15)XN
Available Languages
Table Of Contents
Cisco Packet Data Serving Node (PDSN) Release 3.5 for Cisco IOS Release 12.4(15)XN
Mobile IP Dynamic Home Address Deletes Older Sessions With Different IMSI
PMTU Discovery by Mobile IP Client
Features From Previous Releases
Simple IP Based Service Access
Mobile IP Based Service Access
Session Redundancy Infrastructure
AAA - Authentication and Authorization
Configuring PDSN Session Redundancy
Configuring PDSN Session Redundancy Infrastructure
Protocol Layering and RP Connections
Closed RP Interface Connections
Closed RP Tunnel Setup Procedures
Closed RP Tunnel Clearing Procedures
Closed RP Connection Setup Procedures
Closed RP Connection Release Procedures
Handoff between Closed-RP and Open-RP
Closed-RP/Open-RP Clustering Architecture
Mobility Management With Closed-RP
IOS-SLB on the Supervisor card
Identification of Data Packets For SDB Indication
SDB Indicator Marking for PPP Control Packets
Resource Revocation for Mobile IP
Subscriber Authorization Based on Domain
Volume-based Prepaid Data Service Flow
Duration-based Prepaid Data Service Flow
Volume-based Prepaid Data Service with Tariff Switching
Support for G17 Attribute in Acct-Stop and Interim Records
Configuring Subscriber Qos Profile to PCF
Configuring Bandwidth Policing
Configuring VSAs in Subscriber QoS Profiles
Mobile IP Call Processing Per Second Improvements
Cisco Proprietary Prepaid Billing
Hardware IPSec Acceleration Using IPSec Acceleration Module—Static IPSec
Conditional Debugging Enhancements
Enhancements Prior to Release 3.0
Electronic Serial Number (ESN) in Billing
Support for Mobile Equipment Indentifier (MEID)
PDSN Cluster Controller / Member Architecture
PDSN Controller-Member Clustering
Upgrading the Controller PDSN Software from R1.2 to R2.0
Upgrading the Member PDSN Software from R1.2 to R2.0 and Above
Related Features and Technologies
Supported Standards, MIBs, and RFCs
Determining the Software Version
Upgrading to a New Software Release
Upgrading PDSN Image from YF-based Image to R3.0-based Image
Loading the IOS Image to the MWAM
Creating the CDMA Ix Interface
Creating a Virtual Template Interface and Associating It With the PDSN Application
Enabling R-P Interface Signaling
Configuring User Session Parameters
Configuring PDSN Session Redundancy Infrastructure
Configuring AAA in the PDSN Environment
Configuring RADIUS in the PDSN Environment
Configuring Prepaid in the PDSN Environment
Enabling VPDN in a PDSN Environment
Configuring Proxy Mobile IP Attributes Locally
Configuring Mobile IP Security Associations
Configuring PDSN Cluster Controller
Configuring PDSN Cluster Member
Configuring A11 Session Updates
Configuring SDB Indicator Marking
Configuring SDB Indicator Marking for PPP Control Packets
Configuring Mobile IP Resource Revocation on the PDSN
Configuring Closed-RP Interfaces
Configuring Short Data Burst Flagging
Configuring PDSN Accounting Events
Configuring CDMA RADIUS Attributes
Monitoring and Maintaining the PDSN
Cisco PDSN Configuration for Simple IP
Cisco PDSN Configuration for Simple IP with VPDN
Cisco PDSN Configuration for Mobile IP
Combined Configuration for Cisco PDSN
Closed RP IOS SLB Load Balancing Configuration
Open-Closed RP Configuration Example
Session Redundancy Configuration Examples
Simple IPV6 Configuration Example
AAA Authentication and Authorization Profile
AAA Profiles for Various Service Types
Authentication and Authorization RADIUS Attributes
Accounting Services RADIUS Attributes
Mandatory AVPs in Connection Setup/Release Messages
Q.931 Cause Codes Used in Call Disconnect Notify Message
Cisco Packet Data Serving Node (PDSN) Release 3.5 for Cisco IOS Release 12.4(15)XN
Feature History
This document describes the Cisco Packet Data Serving Node (PDSN) software for use on the Cisco Multi-processor WAN Application Module (MWAM) that resides in the Cisco Catalyst 6500 Switch, and the Cisco 7600 Internet Router. It includes information on the features and functions of the product, supported platforms, related documents, and configuration tasks.
This document includes the following sections:
•
Feature Overview, page 3
•
•
•
•
•
•
•
•
•
•
•
Feature Overview
A PDSN provides access to the Internet, intranets, and Wireless Application Protocol (WAP) servers for mobile stations using a Code Division Multiple Access 2000 (CDMA2000) Radio Access Network (RAN). The Cisco PDSN is a Cisco IOS software feature that runs on MWAM cards on Cisco Catalyst 6500 routers, and the Cisco 7600 Internet Router, where it acts as an access gateway for Simple IP and Mobile IP stations. It provides foreign agent (FA) support and packet transport for virtual private networking (VPN). It also acts as an Authentication, Authorization, and Accounting (AAA) client.
The Cisco PDSN supports all relevant 3GPP2 standards, including those that define the overall structure of a CDMA2000 network, and the interfaces between radio components and the PDSN.
System Overview
CDMA is one of the standards for Mobile Station communication. A typical CDMA2000 network includes terminal equipment, mobile termination, base transceiver stations (BTSs), base station controllers (BSCs / PCFs), PDSNs, and other CDMA network and data network entities. The PDSN is the interface between a BSC / PCF and a network router.
Figure 1 illustrates the relationship of the components of a typical CDMA2000 network, including a PDSN. In this illustration, a roaming mobile station user is receiving data services from a visited access provider network, rather than from the mobile station user's subscribed access provider network.
Figure 1 The CDMA Network
As the illustration shows, the mobile station, which must support either Simple IP or Mobile IP, connects to a radio tower and BTS. The BTS connects to a BSC, which contains a component called the Packet Control Function (PCF). The PCF communicates with the Cisco PDSN through an A10/A11 interface. The A10 interface is for user data and the A11 interface is for control messages. This interface is also known as the RAN-to-PDSN (R-P) interface. For the Cisco PDSN Release 2.0 and above, you must use a Giga Ethernet (GE) interface on the MWAM platform.
Figure 2 illustrates the communication between the RAN and the Cisco PDSN.
Figure 2 RAN-to-PDSN Connection: the R-P Interface
The IP networking between the PDSN and external data networks is through the PDSN-to-intranet/Internet (Pi) interface. For the Cisco PDSN Release 2.0 and above, you can use either an FE or GE interface as the Pi interface.
For "back office" connectivity, such as connections to a AAA server, or to a RADIUS server, the interface is media independent. Any of the interfaces supported on the Cisco 7206 can be used to connect to these types of services; however, Cisco recommends that you use either an FE or GE interface.
How PDSN Works
When a mobile station makes a data service call, it establishes a Point-to-Point Protocol (PPP) link with the Cisco PDSN. The Cisco PDSN authenticates the mobile station by communicating with the AAA server. The AAA server verifies that the user is a valid subscriber, determines available services, and tracks usage for billing.
The method used to assign an IP address and the nature of the connection depends on service type and network configuration. Simple IP operation and Mobile IP operation are referred to as service types. The service type available to a user is determined by the mobile station, and by the type of service that the service provider offers. In the context of PDSN, a mobile station is the end user in both Simple IP and Mobile IP operation.
Once the mobile station is authenticated, it requests an IP address. Simple IP stations communicate the request using the Internet Protocol Control Protocol (IPCP). Mobile IP stations communicate the request using Mobile IP registrations.
The following sections describe the IP addressing and communication levels for each respective topic:
•
•
•
Cisco PDSN Simple IP
With Simple IP, a service provider's Cisco PDSN assigns a dynamic or static IP address to the mobile station during the PPP link setup. The mobile station retains this IP address as long as it is served by a radio network that has connectivity to the address-assigning PDSN.
Therefore, as long as the mobile station remains within an area of RANs that is served by the same PDSN, the MS can move or roam inside the coverage area and maintain the same PPP links. If the mobile station moves outside the coverage area of the given PDSN, the mobile station is assigned a new IP address, and any application-level connections are terminated.
Note
Figure 3 illustrates the placement of the Cisco PDSN in a Simple IP scenario.
Figure 3 CDMA Network - Simple IP Scenario
Cisco PDSN Simple IP with VPDN Scenario
A Virtual Private Data Network (VPDN) allows a private network dial-in service to span to remote access servers called Network Access Servers (NAS). Figure 4 illustrates a VPDN connection in the PDSN environment with Simple IP. In this scenario, the PDSN is acting as the NAS.
Figure 4 CDMA Network —Simple IP with VPDN Scenario
A VPDN connection is established in the following order:
1.
2.
3.
The PPP client is forwarded through a Layer 2 Tunneling Protocol (L2TP) tunnel over User Datagram Protocol (UDP).
4.
Cisco PDSN Mobile IP
With Mobile IP, the mobile station can roam beyond the coverage area of a given PDSN and still maintain the same IP address and application-level connections.
Figure 5 shows the placement of the Cisco PDSN in a Mobile IP scenario.
Figure 5 CDMA Network —Mobile IP Scenario
The communication process occurs in the following order:
1.
2.
As part of the registration process, the HA creates a binding table entry to associate the mobile station's home address with its Care-of address.
Note
3.
4.
5.
6.
7.
Note
Mobile IP Dynamic Home Address Deletes Older Sessions With Different IMSI
The PDSN cannot recognize 1xRTT to EVDO as a handoff due to a change of IMSI. The result is that the "cdma-reason-ind" in the account stop message will not reflect the same.
By default, the PDSN keeps the first call session if the Mobile does a static home address. In this release, the PDSN supports deleting the first call session for dynamic home address cases (for example, 1x-RTT to EVDO handoff where the IMSI changes during the handoff).
The old call scenario is established as follows:
1.
2.
3.
A new CLI is introduced in this release that allows you to delete the old session. When you issue the ip mobile cdma imsi dynamic command, the PDSN releases the old session and allows the new session to come up.
PMTU Discovery by Mobile IP Client
FTP upload and ping from the end node may fail when PMTU Discovery (done by setting the DF bit) is done by a MobileIP client (an end node) for packet sizes of about 1480. Due to failure of PMTUD algorithm, the IP sender will never learn the smaller path MTU, but will continue unsuccessfully to retransmit the too-large packet, until the retransmissions time out.
Please refer to http://www.cisco.com/warp/public/105/38.shtml#2000XP for disabling PMTUD for Windows 2000/XP platforms.
Cisco PDSN Proxy Mobile IP
Currently, there is a lack of commercially-available Mobile IP client software. Conversely, PPP, which is widely used to connect to an Internet Service Provider (ISP), is ubiquitous in IP devices. As an alternative to Mobile IP, you can use Cisco's proxy Mobile IP feature. This capability of the Cisco PDSN, which is integrated with PPP, enables a Mobile IP FA to provide mobility to authenticated PPP users.
Note
The communication process occurs in the following order:
1.
2.
3.
4.
5.
6.
PDSN on MWAM
The MWAM supports the feature set of PDSN Release 3.5, and a Cisco Catalyst 6500 or Cisco 7600 chassis will support a maximum of 6 application modules. Each application module supports 5 IOS images, each with access to 512 Megabytes of RAM. Up to five of these images can function as a PDSN.
Additionally, instances of the cluster controller functionality will be configured as required. One active and one standby controller are required for a cluster of 48 PDSN instances or less. Each PDSN image supports 20,000 sessions. For every 10 PDSNs configured in the chassis, one active and one standby controller is required. Internal to the chassis, the PDSN images are configured on the same VLAN in order to support the Controller-Member architecture (although the architecture itself does not require this). Load balancing external to the chassis is determined by the physical proximity of the chassis and the network architecture. It is possible that you require both a VLAN approach, and a more traditional routed approach.
Features
New Features in This Release
This section describes the following features of the Cisco PDSN Release 3.5:
•
Inter-user priority attribute is used by the PCF to schedule packets to the mobile node. This attribute is received by the PDSN from AAA in a RADIUS access-accept message.
•
This Home Area attribute is defined by Lucent, and is received by the PDSN from AAA in a RADIUS access-accept message.
•
The PDSN polices downstream traffic towards the mobile node based on the "maximum authorized aggregate bandwidth" 3GPP2 attribute, downloaded from AAA.
Features From Previous Releases
This section lists features that were introduced prior to Cisco PDSN Release 3.5:
•
–
•
•
•
•
•
–
–
•
–
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note
Note
Note
P indicates that this feature is only available with a Premium license.
* Requires appropriate hardware support.
Note
PDSN Performance Metrics
Cisco PDSN Release 3.5 delivers the following performance improvements compared to Release 1.2 and 2.1:
•
Performance Metrics on the Cisco 6500 and 7600 series platform are as follows. The quoted figures are per image, and each MWAM can support 5 PDSN images.
•
•
•
•
•
•
•
•
•
•
•
•
Packet Data Service Access
The PDSN supports two types of service accesses. The type of service access for a mobile session is determined by the capabilities of the mobile station:
•
•
Simple IP Based Service Access
The PDSN facilitates a mobile user to access the internet and corporate intranet by using Simple IP based service access. Simple IP mode of access, however, limits user mobility to the coverage area of the serving PDSN. Inter-PDSN handoff causes re-negotiation of PPP between the mobile station and the new PDSN. The old IP address assigned at the previous PDSN can usually not be assigned to the mobile user from the new PDSN, and results in reset and restart of user applications.
Some of the salient features for Simple IP based service access include:
•
•
•
•
•
•
•
•
•
•
•
•
•
User NAI is available during the PPP CHAP/PAP authenticating phase. Domain name information in the NAI determines the domain responsible for user authentication. Based on the type of packet routing model, Simple IP based service access can be categorized as follows.
•
•
•
Simple IP Routed Access
After receiving username and password during PPP LCP negotiations, the PDSN forwards authentication information to the local AAA server via an access request message. This, in turn, may be proxied to the AAA server in the user's home domain, via broker AAA servers, if necessary. On successful authentication, the user is authorized services based on its service profile. User Class/CDMA_IPTECH information, along with other authorization parameters are returned to the PDSN using an access accept message from the home AAA. On successful negotiation of an IP address, Simple IP based services are made available to the mobile user.
Simple IP routed access method is applicable for users that are not configured for VPDN or proxy-Mobile IP services. With PPP terminated at the PDSN, uplink user traffic is routed towards the IP network from the PDSN. The address assigned to the mobile user would be from within the PDSN routable domain. Private addresses may also be used if a NAT is configured. User mobility is limited to the PDSN coverage area. Inter-PCF handoffs do not disrupt service. Inter-PDSN handoffs, however, result in PPP renegotiation at the new PDSN, another IP address being assigned at the new PDSN, and reset and restart of user applications.
Simple IP VPDN Access
After receiving username and password during PPP LCP negotiations, the PDSN forwards authentication information to the local AAA server via an access request message. This, in turn, may be proxied to the AAA server in the user's home domain, via broker AAA servers, if necessary. On successful authentication, the user is authorized services based on user's service profile. If the user is configured for VPDN based access services, User Class information, along with other authorization parameters including tunneling options and tunneling parameters, are returned to the PDSN via an access accept message from the home AAA. The following types of VPDN services are supported at the PDSN:
L2TP - Layer 2 Tunneling Protocol
For L2TP type layer2 tunneling, the PDSN establishes an L2TP tunnel with the tunneling endpoints specified by the tunneling parameters. The L2TP tunnel would be established between the LAC at the PDSN and LNS at the NAS in user's home domain. The PPP connection would be between the mobile station and the LNS in the home network. Despite the PPP connection termination at the LNS, the PDSN monitors the PPP session for inactivity. Status of the PPP connection is also linked with the state of the underlying A10 connection. PPP connection is deleted when the underlying A10 connection is deleted. IPSec encryption methods can also be enabled over the L2TP tunnels for enhanced security.
On successful negotiation of an IP address between the mobile and the LNS, IP-based services are made available to the mobile.
The LNS may be configured to authenticate the mobile user based on the challenge and challenge response information from the PDSN. Additionally, the LNS may also be configured to challenge the user again after the layer2 tunnel has been established. The following authentication options are supported for L2TP:
•
The LAC (PDSN) challenges the mobile user and forwards authentication related information to the LNS as part of tunnel setup parameters. The LNS may be configured to authenticate the user either locally or via the home AAA, based on the authentication related information from the LAC (PDSN). On successful authentication, the mobile and the LNS proceed with the IPCP phase and negotiate an IP address for the user session. Call establishment procedures for this scenario are illustrated in Figure 16.
•
The LAC (PDSN) challenges the mobile and forwards authentication related information to the LNS as part of tunnel setup parameters. The LNS may be configured to authenticate the user either locally or via the home AAA, based on the authentication related information from the LAC (PDSN). On successful authentication, the LNS challenges the mobile again. After successful authentication, the LNS and the mobile proceed with IPCP phase and negotiate the IP address for the user session.
Proxy-Mobile IP Access
After receiving username and password during PPP LCP negotiations, the PDSN forwards authentication information to the local AAA server via an access request message. This, in turn, may be proxied to the AAA server in the user's home domain, using broker AAA servers, if necessary. On successful authentication, the user is authorized services based on its service profile. User Class information, along with other authorization parameters are returned to the PDSN via an access reply from the home AAA.
If the user is configured for proxy-Mobile IP based access, authorization parameters from the home AAA include the Home Agent (HA) address, and the security parameter (SPI) to be used for computing the MN-HA Authentication extension for the mobile station. The Home Agent is allocated from the list of Home Agents configured at the home AAA server. Round robin or hashing algorithms based on user NAI can be used for allocating a Home Agent at the AAA. Other authorization attributes returned from the AAA include MN-AAA authenticating extension as defined in RFC 3012. Based on this information, the PDSN performs proxy-Mobile IP procedures on behalf of the mobile user by sending a Mobile IP Registration Request message to the allocated HA. On successful authentication of the mobile with the AAA, and registration at the Home Agent, the Home Agent assigns a home address for this mobile user This address is returned to the mobile during IPCP IP address negotiation phase.
On successful negotiation of an IP address, proxy-Mobile IP based services are made available to the mobile user. To the mobile, these services are no different from Simple IP services with tunneling being done via the Home Agent. This feature, however, extends the coverage area of the call beyond coverage area of the serving PDSN. If, as a result of a handoff event, another PDSN is allocated to the call, the target PDSN performs Mobile IP registration with the Home Agent thereby ensuring that the same home address is allocated to the mobile.
Mobile IP Based Service Access
The PDSN allows a mobile station with Mobile IP client function, to access the internet and corporate intranet using Mobile IP based service access. With this mode of service access, user mobility is extended beyond the coverage area of currently serving PDSN. Resulting from a handoff, if another PDSN is allocated to the call, the target PDSN performs Mobile IP registration with the Home Agent thereby ensuring that the same home address is allocated to the mobile.
Some of the salient features for Mobile IP services access include:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
A Mobile IP capable mobile client may be configured to skip PAP/CHAP based authentication during the PPP LCP phase. Once the PPP is established, the PDSN sends a burst of Mobile IP Agent Advertisement messages that include the Mobile IP Agent Advertisement Challenge extension specified in RFC 3012. The number and timing of the burst is configurable. The mobile user responds with a Mobile IP Registration Request message that includes the mobile user's NAI and MN-FA Challenge extension in response to the challenge in the Agent Advertisement message. If the mobile user does not respond to the initial burst, advertisements can be solicited.
The Foreign Agent function at the PDSN can be configured to authenticate the mobile user by forwarding an access request message to the local AAA server. The local AAA server would proxy the message to the home AAA server, via broker AAA server(s), if necessary. On successful authentication, the home AAA may assign a Home Agent to the call and return its address in the access reply message. Other authorization parameters in the access-reply message include the SPI and IPSec shared key to be used between the FA and the HA. The PDSN/FA and Home Agent establish a secure IPSec tunnel, if required, and the PDSN/FA forwards the Registration Request message to the Home Agent. The Registration Request message includes the NAI and MN-FA-Challenge Extension also. It may also include MN-AAA Authentication extension.
The Home Agent can be configured to authenticate the mobile again with the home AAA. On successful authentication and registration, the Home Agent responds with a Registration Reply message to the PDSN/FA, which is forwarded to the mobile station. The Registration Reply message contains the home address also (static or dynamically assigned) for the user session.
Potential home addresses are available to the PDSN from the following:
•
•
•
The mobile may be configured to perform PPP PAP/CHAP authentication in addition to performing Foreign Agent Challenge based authentication specified in RFC 3012. In this case the PDSN would support one Simple IP flow, in addition to one or more Mobile IP flows.
For Mobile IP services, the Home Agent would typically be located within an ISP network or within a corporate domain. However, many of the ISPs and/or corporate entities may not be ready to provision Home Agents by the time service providers begin rollout of third-generation packet data services. Access service providers could mitigate this situation by provisioning Home Agents within their own domain, and then forward packets to ISPs or corporate domains via VPDN services.
Binding Update Procedures
When a mobile first registers for packet data services, a PPP session and associated Mobile IP flow(s) are established at the PDSN. In the event of an inter-PDSN handoff, another PPP session is established at the target PDSN, and the mobile registers with the Home Agent via the new PDSN/FA. The Visitor list binding and the PPP session at the previous PDSN are, however, not released until the PPP inactivity timer expires.
Idle/unused PPP sessions at a PDSN consume valuable resources. The Cisco PDSN and Home Agent support Mobile IP Resource Revocation as defined in IS83C and Cisco Proprietary Binding Update and Binding Acknowledge messages for releasing such idle PPP sessions as soon as possible. Mobile IP Resource Revocation is described in Section 16 in greater detail
If Cisco Proprietary binding update feature is used, in the event of an inter-PDSN handoff and Mobile IP registration, the Home Agent updates mobility binding information for the mobile with the Care-of-Address (COA) of the new PDSN/FA. If simultaneous bindings are not enabled, the Home Agent sends a notification in the form of a Binding Update message to the previous PDSN/FA. The previous PDSN/FA acknowledges with Binding Acknowledge, if required, and deletes visitor list entry for the Mobile IP session. The previous PDSN/FA initiates the release of the PPP session when there are no active flows for that mobile station.
The sending of the binding update message is configurable at the Home Agent.
Note
Simple IPv6 Access
The PDSN simple IP service has been enhanced to allow both simple IPv4 and simple IPv6 access. These protocols can be used one at a time, or at the same time. The ipcp and the ipv6cp are equivalent for each protocol.
An IPv6 access uses the same PPP LCP authentication and authorization procedures, as well as the AAA access. When an RP connection is established, the MS sends a PPP Link Control Protocol (LCP) Configuration-Request for a new PPP session to the PDSN. The PPP authentication (CHAP/PAP/none) is one of the parameters negotiated during the LCP phase. After the LCP parameters are negotiated between the MS and the PDSN, an LCP Configure-Acknowledge message is exchanged. Once LCP is up, the PPP authentication is started.
The authentication phase uses CHAP, PAP, or none, depending on the configuration and LCP negotiation. After authentication, the NCPs, ipcp and/or ipv6cp, can be started. A simultaneous IPv4 and IPv6 access from an MS shares the common LCP authentication and authorization as well as the AAA correlation-id parameter.
The ipv6cp protocol negotiates a valid non-zero 64-bit IPv6 interface indentifier for the MS and the PDSN. The PDSN has only one interface-identifier associated with the PPP connection, so it will be unique. Once ipv6cp has been successfully negotiated, the PDSN and MS both generate unique link-local addresses for the IPv6 interface. The link-local addresses are generated by pre-pending the link-local prefix, FE80:/64, to the 64-bit interface-identifier negotiated during the ipv6cp phase (for example, FE80::205:9AFF:FEFA:D806). This gives a 128-bit link-local address.
The PDSN immediately sends an initial unsolicited Router Advertisement (RA) message on the PPP link to the MS. The link-local address of the PDSN is used as the source address and the destination address will be FF02::1, the "all nodes on the local link" IPv6 address. The PDSN includes a globally unique /64 prefix in the RA message sent to the MS. The prefix may be obtained from a local prefix pool or from AAA. The MS will construct a global IPv6 unicast address by prepending the prefix received in the RA to the lower 64-bit interface identifier. You should carefully configure the PDSNs so that the /64 prefix is globally unique for each MS.
After a successful ipv6cp negotiation phase and configuration of the link-local address, the MS transmits a Router Solicitation (RS) message if an RA message has not been received from the PDSN within some specified period of time. The RA is necessary for the MS to construct its 128-bit global unicast address.
In contrast to IPv4, an IPv6 MS will have multiple IPv6 addresses, including:
•
•
•
An IPv6 address is 128-bits for both source and destination addresses. The /64 designation means that 64-bits are used for the prefix (upper 64-bits). This is similar to an IPv4 netmask. A /128 address would mean that the entire address is used. Refer to RFC-3513 for additional IPv6 addressing details and information.
Configuring Simple IPV6
The following commands are used to configure simple IPV6 on the Cisco PDSN, and are listed in the Command Reference:
•
•
•
•
•
•
•
The following configuration commands are required for IPv6:
Global Configuration Commands
•
•
•
Virtual-template Interface Commands:
•
•
•
•
•
Other commands
•
Please refer to the Cisco IOS IPV6 Command Reference at the following URL for more detailed information regarding these configuration commands:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_command_reference_book09186a00801d661a.html
Session Redundancy Infrastructure
Note
PDSN session redundancy is focused on preserving user flows on fail-over. Support for the continuity of billing records, internal counters, and MIB variables is secondary. The following conditions need to exist for fail-over to be successful on the PDSN:
•
•
•
Functional Overview
The PDSN Session Redundancy feature provides user session failover capability to minimize the impact of a PDSN failure on the mobile user experience. The PDSN uses a 1:1 redundancy model, with a standby present for every active PDSN. The active PDSN sends state information to the standby PDSN for synchronization on an as-needed basis. When a PDSN failure occurs, the standby PDSN has the necessary state information to provide service to all existing sessions. It then takes over as the active PDSN and services user sessions, thus providing session redundancy. When the previously active PDSN comes back online, it assumes the role of standby for the now active PDSN, and receives state information for all existing sessions from the newly active PDSN.
Under normal operating conditions, the active and standby PDSN pairs are two separate PDSN images that have identical configurations. They share one or more HSRP interfaces, which are used by all external entities to communicate with them. The active PDSN synchronizes session data to the standby PDSN based on events described below.
Session Events
When a new user session needs to be established, the PCF first sets up an A10 connection to the active PDSN using the HSRP address known to the PCF. The MN then sets up a PPP connection with the active PDSN using the A10 tunnel. Once the call is in a stable state (the PPP session is successful), the active PDSN then syncs relevant state information to the standby PDSN. The standby then duplicates the actions of the active PDSN with regards to the A10 connection and the PPP session, and awaits further updates from the active. When any of the other events as listed below occurs, the active PDSN sends state information to the standby.
In order to minimize the loss of accounting data in the event of a failover, a periodic accounting update, with configurable frequency shall run on the active PDSN. Every periodic update for a session shall trigger a sync sent to the standby PDSN, which shall update its accounting data. Only counters and attributes that undergo a change on the active PDSN are synced to the standby periodically. Information since the last accounting synchronization point will be lost. Also, in order to ensure that the latest information is correctly conveyed to the billing system, the standby unit will never send out any accounting records to the AAA server. The records are always sent from the Active Unit.
Session events that lead to a sync are:
•
•
•
•
•
•
•
•
•
Active PDSN Failure
In the event that the standby PDSN detects that the active PDSN has failed (using HSRP), it then takes over as the active PDSN. Since all external entities, including PCFs, AAA servers, and Home Agents are configured to communicate with the PDSN pair only using the HSRP addresses, once the standby PDSN takes over those addresses, they are unable to detect a failure. All stable calls also have their state synced to the standby; therefore the standby is able to start forwarding user traffic once it takes over as active. On the standby all timers (such as A11 lifetime, PPP timers, and Mobile IP lifetime) are started at the time it takes over as active. Accounting data is also synchronized to the extent that the periodic accounting sync timer has been configured on the PDSNs.
Standby PDSN Start-up
When a PDSN comes up when there is an existing active, it takes over the standby role. When the active PDSN learns that a standby PDSN is available, it goes through a process of transferring state data for all existing user sessions to the standby, called a Bulk Sync. Once this process is complete, the standby PDSN is then ready to take over as active in the event of a failure.
Handling Active-Active Scenario
If there is a link failure or a failure in an intermediate node, HSRP packets sent will not reach the peer and the standby node would assume that the active has reloaded and transitioned to active state. This leads to a situation of Active-Active PDSN nodes. The requirement is that, in case one of the PDSNs continues to receive traffic while the other is isolated from the network, it is ensured that the node which received traffic should remain active once the link is restored.
To achieve this, an application tracking object is introduced and HSRP priority is altered based on whether PDSN is processing traffic after the HSRP peer is lost. The PDSN will lower its HSPR priority once it detects that the peer PDSN is lost. Afterward, when the PDSN processes traffic (either control or data packets), it raises its priority back to the configured value. This helps to choose the active node after the link is restored between the PDSNs. So the node which received traffic in Active-Active situation remains to be Active after link restoration.
Other Considerations
A Redundancy Framework (RF) MIB is available in order to monitor the active and standby status of the two PDSNs. Other MIB variables and internal counters are not synchronized between the Active and Standby. They start from the values following IOS-Load or Reload on the backup image. The backup image is treated as a new box.
The PDSN redundant pair is treated as a single member by the cluster controller, and is transparent to the PDSN clustering mechanism. The cluster controller is oblivious to a failover from an active PDSN to its redundant standby.
Similarly, a PDSN redundant pair appears as a single PDSN to all external entities, such as the PCF, the HA, and the AAA server.
IPSec security associations for FA-HA connectivity are maintained across fail-over.
Note
Note
In Process Sync Events
The following subsections explain the expected behavior of the PDSN under session redundancy for various sync events in process.
Call Setup
The state of "sessions-in-progress" is not preserved during fail-over. Mechanisms such as R-P connection retry from the PCF will ensure that sessions will be established as required.
It is possible that a fail-over can occur when the PCF has established an R-P session for a user flow, but user flow establishment is not completed. In this case, fail-over will result in the R-P session not being present on the standby. The PCF will timeout the R-P session on the next R-P session lifetime refresh. If the user attempts to establish a new session during this time, a new session will be created.
Call Teardown
There are four scenarios for session termination. These include the following:
•
•
•
•
For each of these cases, session teardown is a multi-step process. For example, a fail-over can occur when a Registration Update message has been sent from the PDSN and the acknowledgement has not been received. In this case, the standby PDSN will already have been told to delete the session. The active PDSN will not wait for an update acknowledgement from the PCF.
If a fail-over occurs after sending the Registration Update to the PCF but before the standby has been told to delete the session, or the request to delete the session is lost, the session will remain established on the standby.
Another case is that the PPP context has been deleted as a result of mobile-initiated termination, and then fail-over occurs prior to the R-P session being terminated.
Similarly, expiry of the PPP Idle timer on the PDSN could also result in deletion of PPP context followed by fail-over prior to R-P session termination.
In these cases, either the Mobile IP Registration Lifetime or the PPP Idle Timeout will expire, and the session is terminated.
Flow Setup
Flows that are in the process of being established are not preserved. You will see this as failure to establish the flow, and you will have to re-establish the flow.
Flow Teardown
This section applies when a session has two or more flows. Currently only a MoIP call supports this case. For an SIP call, only one flow is allowed.
Although a MoIP flow is preserved after switchover, it is possible that registration lifetime expiration will lead to deletion of the flow. If the same user registers again before the lifetime expires, it will be considered as a re-registration since this is an existing visitor. However, the re-registration may or may not succeed, depending on the following conditions:
1.
2.
Dormant-Active Transition
The transition is synchronized between active and standby, and would fall into following scenarios:
1.
2.
However, packets will be switched and counted. The PDSN-related show commands may not show all the right information about the session. The subsequent transition from active to dormant will not cause difficulties as the session remains dormant on the PDSN.
3.
4.
Handoff
Inter-PCF Handoff (Dormant or Active) - Same PDSN
The most significant problem with hand-off is to re-establish the data path between the target PCF and the now-active PDSN for the preserved session, irrespective of whether this is an active or dormant handoff. Again, there is a window between handoff actually being completed and the state being synchronized within which a fail-over can occur.
There are the following scenarios:
1.
2.
3.
Inter-PCF Handoff (Dormant or Active) - Different PDSN
This kind of handoff is indicated to the PDSN by receipt of an A11 Registration Request containing the PANID and CANID. It also includes the Mobility Event Indicator and Accounting Data (R-P Session Setup Air-link Record). From the perspective of High Availability, this looks like a new session establishment on the newly active PDSN and a 'regular' session termination on the old PDSN.
A11 Re-registrations
A11 Re-registration RRQ is received by the active unit. The registration life timer does not start on the standby, but it keeps track of the life timer value so that it can restart the life timer once it becomes active. If the lifetime in the re-registration RRQ is different from the previous RRQ, the new lifetime is synced to the standby. For example, if a previous RRQ carries a lifetime of 300 seconds and now a new RRQ has the value changed to 500 seconds, the new value is synced to the standby. Other significant parameters included in the re-registration RRQ are also synced to the standby.
Now, in the above example, if the failover occurs before syncing the new lifetime to the standby, the standby will start the lifetime for 300 seconds.
PPP Re-negotiation
Upon PPP renegotiation, the PDSN deletes all the flows on the RP session and sends accounting STOP for each flow. Once PPP is up again, the PDSN creates new flow(s) for the session. Therefore, when PPP renegotiation happens on the active, the active unit will send a PPP renegotiation notification to the standby which will then delete all the flows from the RP session on the standby. Once PPP is up again and a new flow is created on the active, the active unit sends each flow's data to the standby. If the failover occurs during PPP re-negotiation, the re-negotiation will fail, and the session may be torn down on the newly active unit.
Other Considerations
Timers
The following timers are normally running when a session is established
•
•
•
•
The following timers may be running, depending on configuration
•
These timers are restarted on the standby when fail-over occurs, and the elapsed time is not synchronized to the standby. The effect will be to extend the timers beyond their original values by a time equal to the time that has already expired. This ensures that the user will not perceive a session failure on fail-over.
Restrictions
The following restrictions exist for the PDSN Session Redundancy Feature:
•
Setting the revocation timestamp to "msec" (ip mobile foreign-service revocation timeout 5 retransmit 4 timestamp msec) for PMIP flows with Session Redundancy is not permitted.
The "msec" option puts the uptime in the timestamp field, and the uptime of the standby router is expected to be lower after switchover when the standby PDSN takes over as active (and when the PMIP flow was closed). Therefore, revocation on HA will be ignored because the identifier value in the revocation message is less than what is expected by HA.
•
Internals
The following sections identify information that is synced to the standby unit:
AHDLC
The control character mapping per used AHDLC channel is preserved. As the default is normally used, only those that are different are synchronized. The AHDLC channel number is not synchronized; an available channel will be selected independently on the standby.
GRE - RP Interface
The GRE Key is synchronized. The flags are synchronized as the sequence flag can be set on a per user basis.
RP Signaling
The contents of the A11 messaging will be treated as described below.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PPP
All LCP options are synchronized. For IPCP, only the IP address and IPHC parameters are synchronized. DNS server IP address negotiated during IPCP negotiation is not synchronized to the standby unit. All per user attributes downloaded from AAA during authentication/authorization are synchronized to the standby unit.
Compression - Header and Payload
There is no synchronization of compression context for either header or payload compression. Fail-over to a standby PDSN results in the compression context being re-established.
Header compression - First packet for a session after switchover is dropped, and peer retries the packet after acknowledge timeout.
Payload compression - There is no compression history present after switchover on the standby. A CCP reset is automatically generated when decode fails. No special treatment is needed.
IP Address Assignment
When an IP address is dynamically assigned from a pool configured on the PDSN, it is necessary that the standby associates the same address with the session. The IP address will be synchronized as part of PPP state. If the IP address is received from AAA or a static IP address is used that does not come from a local pool, this address will also be associated with the session on the standby. Similarly, the address pool will be synced.
AAA - Authentication and Authorization
Table 2 lists the relevant Authentication and Authorization parameters. This is required on the standby to allow accurate recreation of AAA state.
GPP2 Packet Data Service Attributes
Table 3 lists the 3GPP2 Packet Data Service Attributes.
AAA Accounting
GPP2 Accounting Records Fields
Table 4 identifies the GPP2 accounting records fields.
Radius Server Group Support
The IP address of the AAA server chosen will not be synchronized.
Mobile IP Signaling
For Mobile IP service, the parameters to be synchronized, per MIP flow, include the following:
•
•
•
•
•
•
•
•
Mobile IP Tunneled Traffic
This traffic is carried in either GRE tunnels or IP-in-IP tunnels. The only information that needs to be synchronized is the tunnel endpoint of the peer.
Locally Configured IPSec
For the PDSN on the Cat76xx, IPSec tunnels are terminated on the Macedon VPN Acceleration Module. The role of the PDSN is to retrieve parameters from AAA and, based on these, 'trigger' IPSec tunnel establishment. Synchronization of these parameters is sufficient to preserve IPSec tunnels in the event of PDSN fail-over for intra-chassis configurations. PDSN failover is not coupled with VPN Acceleration Module/SUP failover. Inter chassis configurations and intra-chassis Macedon/SUP failover does not currently support stateful IPSec.
FA-HA IPSec
FA-HA IPSec tunnels will be preserved when PDSN on 7600 fail-over occurs for intra-chassis configurations. They will not be preserved for inter chassis configurations.
AAA Accounting
Periodic Accounting Sync
Accounting information is optionally synchronized between the active and standby images. This synchronization occurs at the configured periodic accounting interval. The counters that are synchronized are g1 and g2, along with the packet counts. Sending an Interim Accounting record will trigger synchronization of the byte and packet counts. Setting the operator-defined periodic accounting interval determines the accuracy of the user-billing record as impacted by PDSN fail-over. It is possible that undercharging could occur; however, overcharging is not possible.
Accounting with VSA Approach
After a switchover takes place, the first interim or stop accounting record (as appropriate) includes a VSA (cdma-rfswact) indicating that a switchover has occurred. The inclusion of this VSA is controllable by issuing the cdma pdsn redundancy accounting send vsa swact command.
Note
Here is a sample accounting debug with vsa:
Sep 13 18:23:10.179: RADIUS: Cisco AVpair [34] 16Sep 13 18:23:10.179: RADIUS: 63 64 6D 61 2D 72 66 73 77 61 63 74 3D 31 [cdma-rfswact=1]System Accounting
In a session redundancy setup, an accounting ON will be sent by the active unit only when the whole setup is brought up (accounting ON will not be sent by the newly active unit after a failover). The standby unit does not send any system accounting events under any scenarios. The events, however, are sent in a standalone mode.
A sys-off is sent if reload is issued on the active unit.
Configuring PDSN Session Redundancy
The following new commands have been introduced for PDSN Session Redundancy:
Enabling PDSN Session Redundancy
The active PDSN shall be able to synchronize the session and flow related data to its standby peer provided the redundancy capability has been enabled. By default this capability is disabled.
The commands syntax is as follows:
[no] cdma pdsn redundancy
When the above CLI is configured, session redundancy is enabled provided the underlying redundancy infrastructure has been configured. The redundancy functionality for PDSN is disabled when the above command with no is executed.
Periodic Accounting Counters Synchronization
The active PDSN by default will not try synchronizing accounting counters periodically. To enable periodic accounting counters synchronization, configure the following command:
[no] cdma pdsn redundancy accounting update-periodic
The no form of the command is used to go to the default behavior. When configured, the byte and packet counts for each flow are synced from the active to the standby unit (only if they undergo a change) at the configured periodic accounting interval (using aaa accounting update periodic xxx). If periodic accounting is not configured, the byte and packet counts will not be synced.
Debug Commands for PDSN-Session Redundancy
In order to facilitate the identification of problem areas of PDSN high availability, the following debug commands are introduced for debugging. All of these debug can be turned off using either undebug all or no debug all, if desired.
[no] debug cdma attribute
[no] debug cdma pdsn redundancy packets
To debug and collect any data pertaining to PDSN-SR, the above command is executed and the details pertaining to redundancy data is sent to the console.
[no] debug cdma pdsn redundancy errors
To debug the PDSN-SR redundancy errors the above command is executed and the details pertaining to A11 data is sent to the console.
[no] debug cdma pdsn redundancy events
To debug events for PDSN session redundancy events, above command is executed and the details pertaining to PDSN (e.g. RP) data is sent to the console.
Display of Redundancy Statistics
When a pair of PDSNs is operating in an active and a standby mode, it is desirable to show or display a variety of information about the sessions and its associated flows that have been synchronized to the standby. The following command shall allow the operator to view the session redundancy data for PDSN.
show cdma pdsn redundancy statistics
On execution the above command displays a number of data items; some of the examples are as follows:
–
–
–
–
–
Note
show cdma pdsn redundancy
On execution of this command, in addition to existing data being displayed, it will also output "pdsn redundancy is enabled," or "redundancy is not enabled," depending on whether the redundancy feature for PDSN has been turned on, or not.
Clearing of PDSN Session Redundancy Statistics
clear cdma pdsn redundancy statistics
On execution of this command, all the data counters associated with the PDSN session redundancy will be actualized to initial value.
Other Debug Commands
In addition to the PDSN-SR debugging commands described above, the following commands associated with high availability are also useful debugging aid:
debug redundancy inter-device
debug ccm
Other Show Commands
In addition to the PDSN-SR show commands described above, the following commands associated with high availability are also useful:
show redundancy inter-device
Configuring PDSN Session Redundancy Infrastructure
The PDSN-SR feature uses the Cisco IOS Check-point Facility (CF) to send stateful data over Stream Control Transmission Protocol (SCTP) to a redundant PDSN. Additionally, in conjunction with Cisco IOS HSRP, the PDSN uses the Cisco IOS Redundancy Facility (RF) to monitor and report transitions on Active and Standby PDSNs.
Before you configure PDSN-SR, you need to configure the inter-device redundancy infrastructure.
Configuring HSRP
The Hot Standby Router Protocol (HSRP) provides high network availability because it routes IP traffic from hosts on networks without relying on the availability of any single router. HSRP is used in a group of routers for selecting an Active router and a Standby router. HSRP monitors both the inside and outside interfaces so that if any interface goes down, the whole device is deemed to be down and the Standby device becomes active and takes over the responsibilities of an Active device.
When configuring HSRP, note that the following recommendation and restrictions apply:
•
–
–
–
–
•
•
Note
•
Use the same group number for each PDSN follow group as is defined for the primary group. Using the same group number for the primary and follow groups facilitates HRSP group setup and maintenance in an environment that contains a large number of PDSN interfaces and HRSP groups.
More information on HSRP configuration and HSRP groups can be found here:
http://www.cisco.com/en/US/partner/tech/tk648/tk362/tk321/tsd_technology_support_sub-protocol_home.html
and
http://www.cisco.com/en/US/partner/tech/tk648/tk362/technologies_configuration_example09186a0080094e90.shtml
Enabling HSRP and Configuring an HSRP Master Group
To enable HSRP on an interface and configure the primary group, use the following commands in interface configuration mode:
Step 1
Enables the HSRP on the interface.
Step 2
Set the Hot Standby priority used in choosing the active router. The priority value range is from 1 to 255, where 1 denotes the lowest priority and 255 denotes the highest priority. Specify that, if the local router has priority over the current active router, the local router should attempt to take its place as the active router.
Step 3
Specifies the name of the standby group.
Step 4
(Optional) Configures HSRP to use the burned-in address of an interface as its virtual MAC address instead of the preassigned MAC address.
Configuring Follow Groups
HSRP follow groups are configured to share the HSRP parameters of the primary group by defining a follow group on the interface using the standby interface configuration command with the follow keyword option specified. Interfaces that share a group track states together and have the same priority.
To configure an interface to follow a primary group, use the following command in interface configuration mode:
Step 1
Specifies the number of the follow group and the name of the primary group to follow and share status.
Note
Step 2
Specifies the group number and virtual IP address of the follow group.
Note
Enabling Inter-Device Redundancy
To enable inter-device redundancy, use the following commands beginning in global configuration mode.
Step 1
Configures redundancy and enters inter-device configuration mode.
To remove all inter-device configuration, use the no form of the command.
Step 2
Defines the redundancy scheme that is to be used. Currently, "standby" is the only supported scheme.
standby-group-name-Must match the standby name specified in the standby name interface configuration command (see the "Configuring HSRP" section). Also, the standby name should be the same on both PDSNs.
Step 3
Returns to global configuration mode.
Configuring the Inter-Device Communication Transport
Inter-device redundancy requires a transport for communication between the redundant PDSNs. This transport is configured using Interprocess Communication (IPC) commands.
To configure the inter-device communication transport between the two PDSNs, use the following commands beginning in global configuration mode:
Step 1
Configures the Inter-device Communication Protocol (IPC) and enters IPC zone configuration mode.
Use this command to initiate the communication link between the Active device and the Standby device.
Step 2
Configures an association between two devices and enters IPC association configuration mode.
In IPC association configuration mode, you configure the details of the association, such as the transport protocol, local port and local IP addresses, and the remote port and remote IP addresses.
Valid association IDs range from 1 to 255. There is no default value.
Step 3
Restarts a disabled association and its associated transport protocol. Note Shutdown of the association is required for any changes to the transport protocol parameters.
Step 4
Configures Stream Control Transmission Protocol (SCTP) as the transport protocol for this association and enables SCTP protocol configuration mode.
Step 5
Defines the local SCTP port number to use to communicate with the redundant peer and enables IPC Transport-SCTP local configuration mode.
Valid port numbers range from 1 to 65535. There is no default value.
Note
Step 6
Defines the local IP address that is used to communicate with the redundant peer. The local IP address must match the remote IP address on the peer router.
Step 7
Enables keepalive packets and specifies the number of times that the Cisco IOS software tries to send keepalive packets with a response before bringing down the interface or tunnel protocol for a specific interface.
Valid value for period is an integer value in seconds great than 0. The default is 10. Valid value for retries is an integer value greater than one and less than 355. The default is the previously used value or 5 if there was no value previously specified.
Step 8
Configures the message retransmission time. Valid range is 300 to 60000 milliseconds. The minimum default is 1000. The maximum default is 60000.
Step 9
Configures the maximum number of keep-alive retries before the corresponding destination address is marked inactive. Valid range is 2 to 10. The default is 5.
Step 10
Defines the maximum number of retransmissions over all destination addresses before an association is declared failed. Valid range is 2 to 20. The default is 10.
Step 11
Exits IPC transport - SCTP local configuration mode.
Step 12
Defines the remote SCTP port that is used to communicate with the redundant peer and enables IPC Transport-SCTP remote configuration mode. Valid port numbers range from 1 to 65535. There is no default.
Note
Step 13
Defines the remote IP address of the redundant peer that is used to communicate with the local device. All remote IP addresses must refer to the same device. To remove an association configuration, use the no form of the command.
Using the Loopback Interface For the PDSN-AAA Server Interface
To ensure that the AAA server views the active and standby units as a single NAS, the same NAS IP address should be used by both the units. Now, the NAS IP Address can be configured for the PDSN using the ip radius source-interface command. When configured, the IP address of that interface is used as the NAS IP Address.
However, the command does not support virtual IP addresses (HSRP). As a result, the only way to ensure that both the units appear as a single NAS is to configure a loopback interface, and use that interface as the source-interface. In short, the CLI would look something like:
ip radius source-interface Loopback1
Configuring Application Tracking to Handle Active-Active Situation
Step 1
Defines a tracking object for PDSN application.
Step 2
Associates the tracking object defined for PDSN with the HSRP config. HSRP would start tracking the state of this object. The configured decrement priority is used to change the HSRP priority based on the state of the tracking object. If the tracking object is "UP", HSRP will have the configured priority. If the tracking object is "DOWN", HSRP decrements its priority by the decrement priority specified in the standby track command.
Note
Protocol Layering and RP Connections
Each mobile station has a single PPP connection with the PDSN, and for each PPP connection there is a corresponding R-P connection between the PDSN and the Base Station/ PCF. R-P connection-related information is maintained for the duration of the PPP connection.
Additionally, the PPP connection and the associated HDLC, LCP, CCP and IPCP state information is also maintained for the duration of the packet data session. One Simple IP flow and several Mobile IP flows can be supported over a single PPP connection.
Open RP Interface Connections
An R-P connection represents the logical tunnel between the PDSN and the Base Station/PCF. It enables bearer data for a PPP connection to be transported between the PDSN and the Base Station/PCF. R-P connection state information is maintained at the PDSN for the duration of the PPP connection. During handoff, the mobile station may connect the PDSN through another Base Station/PCF entity resulting in establishment of another R-P connection between the PDSN and the new Base Station/PCF. This results in the release of the R-P connection between the PDSN and the old Base Station/PCF.
R-P connection state information is maintained at the PDSN even during the dormant phase of the session. When a mobile station transitions to active state, this information allows the PDSN to associate the mobile station with an already available PPP connection. Loss of R-P state information results in the release of the PPP connection by the PDSN. As a result, a mobile station accessing packet data services following the loss of an R-P connection results in the establishment of a new PPP connection, and the reset and restart of user applications. Therefore, the PDSN retains the R-P connection state information to ensure minimal disruption of user applications during transitions between active and dormant session phases.
Closed RP Interface Connections
The Closed RP Interface is an L2TP standard-based interface that establishes an L2TP Tunnel between the PCF and PDSN to carry signaling information and user traffic for Packet Data Services. The Closed R-P connection state information is maintained at the PDSN for the duration of the PPP connection. During handoff, the mobile station may connect to the PDSN through another Base Station/PCF entity (thereby establishing another R-P connection between the PDSN and the new Base Station/PCF). In this scenario, the R-P connection between the PDSN and the old Base Station/PCF is released. In the Closed RP interface, the PDSN has no knowledge of dormancy.
Note
PPP Connections
A PPP connection represents the link layer connectivity between the mobile station and the PDSN. It includes the HDLC state, negotiated LCP parameters, negotiated IP address and CCP compression state tables, etc. Peer PPP entities may re-negotiate LCP and CCP parameters during an active session without compromising continuity of user sessions; however, user identity, authentication-related information and negotiated IP addresses are retained, thus ensuring that applications established over the SimpleIP flow are unaware that renegotiation has occurred. PPP connection state information is retained at the PDSN during dormant phase of the session to ensure minimal disruption of user applications during transitions between active and dormant session phases.
Application Flows
One Simple IP and several Mobile IP flow instances can be supported over a single PPP connection. For each Simple IP flow, the state information includes the associated IP address, NAI and billing related user data records (UDRs), and other related information. For each Mobile IP flow, the state information includes the Mobile IP visitor list information, NAI and UDRs, and other related information.
The Closed RP Interface
The PDSN interfaces with the Radio Network/Base Station to provide a transmission path for the user data stream between the packet network and the radio access network. The PDSN interfaces to the Radio Network using the Packet Control Function (PCF) through the Closed RP interface. This section describes the Closed RP interface in detail.
For the transmission path between the Radio Network and the PDSN, the following conditions are present:
•
•
The Closed RP interface is based on L2TP standard, but supports only Connection/Call Management aspects of that standard. The Closed RP interface definition extends the Call Management messages with some additional AVPs to provide bearer connection to Mobile Stations. The new AVPs include the following:
•
•
•
•
•
•
Supported call control and call management capabilities of the Closed RP signaling interface include the following:
•
•
•
•
•
Closed RP Tunnel Setup Procedures
The PCF initiates the establishment of a Closed RP tunnel when it is brought into service and PDSN IP addresses are statistically configured on it. The PCF establishes a tunnel with each PDSN for which it has an IP address.
The following L2TP control messages are required to set up the tunnel:
•
•
•
•
Closed RP Tunnel Clearing Procedures
Tunnel clearing can be initiated by the PDSN or PCF by sending a Stop Control Connection Notification Message and ZLB is sent to acknowledge the message.
The PDSN can be configured to initiate tunnel termination in the following scenarios:
•
•
Closed RP Connection Setup Procedures
When a mobile user initiates a packet data call by sending an IS-2000 origination message, normal voice service authentication procedures are followed for the subscriber, and a traffic channel is established with the mobile. After connection of Packet Data Service Option, RLP synchronization between the Mobile and the BS proceeds. The BS/PCF initiates a Closed RP connection setup by sending an ICRQ message to the PDSN. If the request is acceptable, the PDSN returns an ICRP message with an accept indication. The information elements carried in the setup messages are listed in Table 15 on page 232.
Closed RP Connection Release Procedures
An active packet data session may be released by either the PDSN or PCF by sending a Call-Disconnect-Notify message with Session ID. The information elements carried in the disconnect messages are listed in Table 16 on page 233.
Closed-RP/Open-RP Integration
Cisco PDSN Release 3.0 introduces the Closed-RP and Open-RP Integration feature, which includes the following details:
•
•
Handoff between Closed-RP and Open-RP
PDSN instance will be able to handoff the session between the Closed-RP and Open-RP PCF. During the handoff the PDSN will not re-negotiate the PPP for the session. Also in the accounting records for a Closed-RP PCF only the relevant parameters that are supported in the Closed-RP architecture are sent. For the Open-RP PCF all the 3GPP2 supported accounting parameters will be included records to the RADIUS.
Closed-RP/Open-RP Clustering Architecture
The controller module in the Open-RP clustering architecture supports Closed-RP clustering. In the dual mode, the controller module accepts Closed-RP connections from the Closed-RP PCF, and terminates the connection locally. After it successfully terminates the Closed-RP connection, the controller performs L2TP Tunnel switching on the session to one of the members. The following call control and call management capabilities of the Closed RP signaling interface are supported on the controller:
•
•
•
•
•
Closed-RP Tunnel Setup Procedures
The PCF establishes a Closed RP tunnel when it is brought into service, and PDSN IP addresses are statistically configured on it. PCF establishes a tunnel with each PDSN controller for which it has an IP address.
The following L2TP control messages are required to setup the tunnel in a Controller Closed RP Tunnel Setup
Step 1
Step 2
Step 3
Step 4
Closed RP Tunnel Clearing Procedures
Tunnel clearing can be initiated by the PDSN (Controller / Member) or by Closed RP PCF by sending a Stop Control Connection Notification Message, and ZLB is sent to Ack the message. The PDSN can be configured to initiate the Tunnel termination in the following scenarios
•
•
Here is the Controller Closed RP Tunnel Clearing message flow:
Step 1
Step 2
Note
Closed RP Connection Setup Procedures
The following message flow depicts the Controller Closed RP Connection Setup:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Note
Note
Both 3GPP2 RP and Closed RP share a common MSID to the PDSN member table on the PDSN controller. This enables the PDSN controller to select the same PDSN member during the handoff between the RP technologies.
Closed RP Connection Release Procedure
The following message flow depicts the Controller Closed RP Connection Release procedure:
Step 1
Step 2
Closed RP and Open RP Handoff Procedures
The following message flow depicts the Controller Closed RP Handoff Closed to Open RP PCF procedure:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Step 14
Step 15
Step 16
Step 17
Step 18
Step 19
Step 20
Step 21
The following message flow depicts the Controller Closed RP Handoff Open to Close RP PCF procedure:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Step 14
Step 15
Step 16
Step 17
Step 18
Step 19
Step 20
Step 21
The following message flow depicts the Controller Closed RP Handoff Closed to Closed RP PCF procedure:
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Step 14
Step 15
Step 16
Step 17
Step 18
Step 19
Step 20
Step 21
Step 22
Step 23
Step 24
Step 25
Performance
In the solution controller that anchors the Closed RP session from the PCF, and does L2TP switching of these sessions to the PDSN member, the following performance measurements were found:
•
•
•
Mobility Management With Closed-RP
An important aspect of packet data services is mobility management. A user should be able to maintain an established service even when roaming within and beyond their service provider's coverage area. For such mobility management, the system supports handoffs that are transparent to user applications.
Handoffs
Handoffs occur as a result of user mobility. A CDMA2000 system supports three types of handoffs:
•
This type of handoff occurs when the mobile moves from one BTS coverage area to another BTS coverage area, generally within a BSC/PCF area. This type of handoff is not visible to the PDSN and is not discussed further.
•
This type of handoff occurs when the mobile moves from the radio coverage area served by one BSC/PCF to a coverage area served by a different BSC/PCF, both connected to the same MSC. In this case, the new PCF can often connect to the same PDSN as the old PCF. However, this is not guaranteed.
When a mobile with an active data session hands off from one PCF to another PCF, the target PCF sends an ICRQ with Session Inquiry AVP to all the PDSNs it is connected with. The PDSN that has the PPP session for the Mobile Node replies with ICRP and terminates the RP session with the Source PCF by sending a CDN with Cause Value 253. If none of the PDSNs, connected with the Target PCF has the PPP session for the Mobile Node, the PCF chooses the least loaded PDSN and proceeds with Call Setup.
•
This type of handoff occurs when the mobile moves from the radio coverage area served by one BSC/PCF to a coverage area served by a different BSC/PCF and the new BSC/PCF is connected to a different MSC than the old BSC/PCF. In this case, the new and old PCFs are typically unable to connect to the same PDSN.
This scenario is possible when the mobile moves to a different radio coverage area and the new BSC/PCF connects to a different MSC than the original BSC/PCF. In this case, it is unlikely that the same PDSN will be used. This results in Inter-PCF and Inter-PDSN handoff.
When the target PCF learns that none of the PDSNs host the packet data session for the MN, the least loaded PDSN is selected and the session is set up using the same steps followed in initial call setup. This scenario is same as the new Closed RP connection setup.
IOS-SLB on the Supervisor card
One aspect of the Closed-RP feature requires that you configure Server Load Balancing on the Cisco Supervisor card. IOS-SLB on the Supervisor card provides loadbalancing for the Closed RP Tunnels between the PCFs and PDSNs. The Loadbalancing unit will direct the Closed RP tunnel to the appropriate PDSN instance. The IOS-SLB unit supports redundancy, so that there is no single point of failure for this system. Figure 6 illustrates this configuration.
Figure 6 Closed-RP Server Load Balancing Configuration
PPPoGRE RP Interface
The PDSN interfaces with the Radio Network/Base Station to provide a transmission path for the user data stream between the packet network and the radio access network. The PDSN interfaces to the Radio Network through the Packet Control Function (PCF) using the PPPoGRE RP interface.
The following list describes the transmission path between the Radio Network and the PDSN:
•
•
The PPPoGRE RP interface is based on 3GPP2 TIA/EIA/IS-835 standard for the control and bearer data transport capabilities. The following list describes the differences between the 3GPP2 standard and PPPoGRE RP Interface from the PDSN perspective:
•
•
•
A11 Session Update
This feature is based on Interoperability Specification (IOS) for cdma2000 Access Network Interfaces (Part 7 (A10 and A11 Interfaces) (3G-IOSv4.3) Version 2.0.1 Date: July 2003) and Interoperability Specification (IOS) for cdma2000 Access Network Interfaces (Part 3 Features (3G-IOSv4.3) Version 2.0.1 Date: July 2003 standard). An A11 Session Update message is sent from the PDSN to the PCF to add, change, or update session parameters for an A10 connection. The following parameters are sent from the PDSN to PCF in an A11 Session Update message in a session parameters NVSE extension with Application Type 08H (Session Parameter). These session parameters NVSE extension will also be sent by the PDSN in the A11 Registration Reply messages.
•
–
–
•
–
–
As per the standard cdma2000® Wireless IP Network Standard TIA-835-C, AUGUST 2003, the PDSN will download the Always On Indicator VSA and RN-PDIT VSA from the Radius server (Visited/Home RADIUS) during the authentication phase. If a user initiates multiple packet data sessions, the PDSN may receive more than one RN PDIT VSA from different home domains. In this case, the largest RN PDIT value received from different home domains is sent from the PDSN to the RN. This update may happen during an ongoing packet data session when the PDSN receives a new RN PDIT value that is greater than the one previously sent to the RN. For Handoff scenario the RN-PDIT and Always-On indicator are sent the PCF in the A11 Registration Reply if the Airlink is not dormant.
SDB Indicator Marking
This feature supports short data burst (SDB) applications, such as SIP signaling for PTT applications, and proposes the interaction with the PDSN. SIP is used by PTT applications to signal a PTT call. The message is short and needs to be delivered to the end-user. The Short Data Burst support on the RAN can be used to send these to the end-user, especially when the messages are to be terminated to the mobile. This is especially important when the mobile user is actually dormant.
The proposal consists of two parts:
•
•
Note
Signaling of SDB Indication
The SDB indication is based on the 3GPP2 Proposal Contribution (Ericsson/SKT) A30-20030818-006, where one of the reserved bits in the GRE header is used to indicate the SDB packets from the PDSN for dormant sessions. The PDSN definition of dormancy is Airlink Stop record A11 Registration request is received from the PCF and A11 Registration success reply is sent by the PDSN.
The PDSN may set the B bit to "1" if the GRE frame contains an IP packet suitable for transmission over the air interface in a Data Burst Message. In the PCF-to-PDSN direction, and on the A8 interface, the B bit is set to "0".
Identification of Data Packets For SDB Indication
SDB indication is required for certain types of data only. Packets destined towards the mobiles that match the policy criteria will be chosen for SDB indication provided the mobile is in dormant mode
The local policy can be considered for an initial phase, if the selection of servers or signaling protocols is limited. For example, if there is only a single SIP server sending out SIP signaling message, a combination of port and source IP address may be used. In addition to this, the PDSN can also be configured with the min and max IP length.
On a Cisco PDSN, IOS MQC can be used to apply classification rules for matching packets that require SDB classification. For example, simple classification criteria can include port number, and source IP address range of the server. A more complex classification criterion can include a custom protocol inspection.
If packets pass the classification criteria and the user is dormant, the PDSN will signal SDB indication to the PCF.
To enable this feature, use the following command:
cdma pdsn compliance ios4.1 sdb
This command enables the PDSN to process an SDB record sent from PCF according to IOS4.1 Standard.
If deep classification is required for certain types of payloads such as RTP, or a custom application, IOS NBAR can be used for inspecting these packets. For a detailed description of how to configure IOS NBAR please refer to the documentation on NBAR.
A sample configuration for the classification function is shown here:
class-map match-all sdb-packetsmatch packet length min 100 max 300match protocol <protocol>match access-group <access-group-number>ip access-list <access-group-number> permit ip 192.0.2.0 0.0.0.255 any(This example of access-list allows matching of a certain protocol from servers whose address range is 192.0.2.0/24)
The protocol and the access-group can be set to match the desired packet stream. The match criteria can also include a custom protocol inspection such as
ip nbar custom media_new 8 hex 0x60 dest udp 3001
The above statement classifies all packets with a UDP destination of port 3001, and contains the value 0x60 at offset 8. The protocol media_new can now be used in the match protocol protocol statement.
policy-map sdb-policyclass sdb-packetsset qos-group group-numberThe policy map is then applied to the input interface. The group-number represents the classified match criteria. All packets that are set with the specific group-number will be flagged for SDB usage between the PCF and the PDSN. This is done with the following command:
cdma pdsn a11 dormant sdb-indication gre-flags group-number
The B bit (SDB indication) would be set for packets matching the sdb-indication group-number.
SDB Indicator Marking for PPP Control Packets
While data packets can be sent towards the mobile using SDBs as shown above, SDBs can also be used for delivering PPP control packets. This can be particularly helpful for Always-On sessions, where the session is dormant. Basically, with Always On configured, the PDSN sends out LCP echo requests (and waits for LCP echo replies) to keep the session alive. Hence, when such a session goes dormant, a data channel needs to be setup to deliver these LCP echo requests to the MN. The other option is to use SDBs to deliver the LCP echo requests without setting up a data channel.
Configure the following CLI in conjunction of the above CLIs to enable this feature:
cdma pdsn a11 dormant sdb-indication match-qos-group group-number ppp-ctrl-pkts
Resource Management
Resource management defines the mechanism to release packet data session related resources at the network elements like the PDSN and the HA. Resources may be released due to the session handoff or for administrative purposes.
IS-835-C defines two mechanisms for resource management:
•
•
While resource management based on Packet of Disconnect is applicable to Simple IP, Mobile IP and Proxy Mobile IP flows, resource management based on Mobile IP Resource revocation is applicable only to Mobile IP flows.
The Cisco PDSN supports resource management based on both Packet of Disconnect and Mobile IP resource revocation.
Resource Revocation for Mobile IP
Basic Mobile IP resource revocation is an IS-835-C initiative that defines the methods by which a mobility agent (one that provides Mobile IP services to a mobile node) can notify the other mobility agent of the termination of a registration due to administrative reasons or MIP handoff.
When configured on the PDSN/FA, the Mobility Agent Advertisement extension in the Agent advertisement will have the X bit set, thus advertising support for resource revocation on that link. A PDSN configured to support resource revocation in Mobile IPv4 will include a revocation support extension in all MIP RRQ including re-registrations. If the associated MIP RRP from the HA also includes a valid revocation support extension, then the PDSN will assume the associated registration as revocable.
For a registration that is revocable, if the PDSN/FA needs to terminate the session administratively, the PDSN/FA sends a resource revocation message to the HA and releases the resources held for that registration.
If the resource revocation ACK from the HA is not received within a configurable amount of time, the resource revocation message will be retransmitted.
On receipt of a resource revocation message from Home Agent, and a registration (identified by the home address, care-of address, and Home Agent address) is located, the resources held by that registration are freed, and a resource revocation ACK message is sent back to the Home Agent. If no other Mobile IP registrations are active on the PPP session associated with the revoked binding, then the PDSN will release the associated PPP and R-P sessions for the revoked registration.
Restrictions for Registration Revocation
The following restrictions for Registration Revocation on the PDSN apply:
•
•
•
•
•
•
Packet of Disconnect
Radius Disconnect, or Packet of Disconnect (PoD) is a mechanism that allows the RADIUS server to send a Radius Disconnect Message to the PDSN to release Session related resources. Resources may be released due to the session handoff, or for administrative purposes. Some of the resources identified include PPP, RP sessions and Mobile IP bindings. Support for Radius Disconnect on the Cisco PDSN and Home Agent is TIA835C compliant.
The PDSN communicates its Resource management capabilities to the Home AAA in the Access Request message (sent for authentication/authorization procedure) by including a 3GPP2 Vendor Specific Session Termination Capability (STC) VSA. The value communicated in the STC VSA is obtained in the configuration. The PDSN also includes an NAS-Identifier attribute containing its Fully Qualified Domain Name (FQDN) in the Access Request.
The Home AAA server establishes a relationship between the user and the NAS Identifier/ NAS-IP address to detect a inter-PDSN handoff. If the NAS-Identifier/ NAS IP address received in the Access Request is different from the previously stored value (non-zero), an inter-PDSN handoff is detected.
The Disconnect Request contains the NAS-ID and the Username (NAI) attributes. It can optionally contain 3GPP2 Correlation ID Calling station ID (IMSI) and the Framed IP address—some session identification attributes. A Disconnect Reason VSA is included if a inter-PDSN handoff is detected. The session identification attributes supported by the PDSN are 3GPP2 Correlation ID and Calling station ID (IMSI).
If the 3GPP2 Correlation ID and Calling station ID (IMSI) attributes are received in the Disconnect Request, and the PDSN is able to find the session/flow corresponding to them, the PDSN will terminate the associated flow and send a Disconnect ACK message to RADIUS server. If session is not found for the received attributes, the PDSN will reply back with a Disconnect NACK message with error code "session context not found". If the Disconnect request has invalid attributes (for example, an 8 digit IMSI), the PDSN will reply with a Disconnect NACK with error code "Invalid Request".
The PDSN also supports processing Disconnect Requests that only contain the NAI attribute (if configured). In compliance with the standards, the PDSN terminates all sessions corresponding to the Username received.
The Ballot version mentions that a Disconnect Request can be received at the Home Agent (HA,) but details on the action to be taken in such an event is not detailed. Hence the approach followed is to terminate a specific binding if Framed-IP-Address attribute is received along with NAI, or terminate all bindings for the NAI, if only NAI attribute is received in the Disconnect Request.
The following restriction is present for this feature:
•
The command line interface for this feature will be standard AAA interfaces. The preferred method to configure POD in Release 2.0 and above is to use the aaa server radius dynamic-author command, which leads to a sub-configuration mode that has options to configure clients, security keys, and other variables.
The following NAS global AAA command is used to enable listening for POD packets:
•
The full syntax for this command is:
•
The following debug command is also available:
•
Restrictions for RADIUS Disconnect
•
•
•
Radius Enhancements
PDSN R3.0 includes the following RADIUS enhancements:
•
•
Radius Server Load Balancing
The RADIUS Load-Balancing (RLB) feature shares the load of RADIUS Authentication and Accounting transactions across a set of RADIUS servers. Without RLB, all transactions are sent to the first server considered to be alive in a server group. When this server stops responding and is marked dead, the PDSN fails over to the next one in the group. Using only one server, despite the presence of other usable servers in the group, limits the overall throughput for call setup/teardown.
Radius Server Load Balancing allows the PDSN to distribute the transaction load across multiple servers in a server group. It tracks the slower servers and reduces the transaction load on those servers, and it adapts when a server is marked dead and when it comes back up again.
The transactions are grouped into batches (the size of which is configurable), and each server is assigned a batch to process. The feature then load-balances transactions based on these batches, one batch at a time. When the first transaction is received, the algorithm determines the server with the least outstanding transactions, and this server is assigned the next batch of transactions. Once a batch of transactions has been assigned, the algorithm determines the server with the least outstanding transactions, and this server is assigned the next batch of transactions. Thus, the server with the least outstanding transactions always gets assigned the next batch. This load-balancing scheme can be applied based on a server group. Thus, each server group defined on the IOS platform can have its own load-balancing scheme.
You should exercise care while configuring the batch size. The trade-off in large versus a small batch size is that of throughput versus CPU load. A large batch size results in a lesser amount of computations, and a lower CPU load; however, it may cause a particular server within the server-group to be assigned transactions even though others in the group are idle. For very small batch sizes, the CPU load increases, as it computes outstanding load across servers more often. Lab simulations indicate that a batch size of 25 gives a decent throughput while not adversely affecting the CPU load.
High Latency RADIUS Servers
The algorithm adapts well to servers of varying response times. Servers that are quick have a lower number of transactions outstanding, and are assigned larger number of the incoming transactions. Slower servers get proportionately lower numbers of transactions.
Server Failovers
When a transaction fails over to the next server in the group after a failover, its outstanding count is increased. Thus, failed-over transactions are also load-balanced. When the next batch of transactions is assigned, this server's outstanding count will reflect it's load accurately—both new and failover transactions will be accounted for in the outstanding transaction count.
Dealing with Server Groups
Consider the following two server-groups:
Server-group SG1 with servers S1, S2, S3.
Server-group SG2 with servers S3, S4, S5.
Consider that SG1 is configured to be load-balanced, while SG2 is not. When requests are sent to SG2 these requests are assigned to S3, as it is the first server in the group and its outstanding transaction count will increase. When requests are sent to SG1, these requests are load-balanced across these servers. When sending transactions to S3, the outstanding transaction count for the server will be high because SG2 transactions are assigned directly to it. Thus, it will receive a low proportion of transactions in SG1. This is the preferred behavior, since the goal is to send transactions to servers that are quicker and able to handle more load, where the load is the total transactions a server is handling, not just those of the current server-group.
Preferred Servers
In certain cases, it is desirable to use the same server for all requests for a given session. With RADIUS server load balancing there is no guaranty that this will occur. To avoid such situations a preferred-server indication is introduced in Release 3.0.
Note
The preferred server behavior, which is enabled by default, tries to ensure that all the accounting records (Start, Stop, and Interim) for a session are sent to the same RADIUS server. However, authentication and accounting records for the same session may still be sent to different RADIUS servers as determined by the load balancing algorithm.
The following events may cause accounting records for the same session to be sent to different RADIUS servers:
•
•
The PDSN will try to use the server if possible, but if not, it will fall back to other servers in the group based on the load-balancing mechanism.
When this indicator is used, costs are not considered in deciding which server to use. However, it might not be possible to always use the preferred server. The server may have been marked dead. Or the server may not be usable since it is not part of the server-group that was used for a previous transaction during the session (for example, the Accounting server-group may be different from the authentication server-group). In this case, the algorithm is free to select an alternate server, based on the load-balancing scheme.
Incoming RADIUS Requests
The RADIUS server load balancing feature is not applicable to incoming RADIUS requests (for example, Packet of Disconnect). POD responses require that the server requesting service be the one that is responded to, thus you should not load-balance these requests across servers.
Subscriber Authorization Based on Domain
Cisco IOS provides a "Subscriber Authorization" mechanism to authorize subscribers based on their realm. You can find details of this feature at the following URL:
http://www.cisco.com/en/US/partner/products/ps6350/products_configuration_guide_chapter09186a0080455cf0.html#wp1056463
IS-835 Prepaid Support
The Cisco PDSN 2.0 software release provides real-time monitoring and rating of data calls for prepaid users. The prepaid billing solution for the PDSN is based on the RADIUS (AAA) server, and takes advantage of the existing flow-based accounting functionality. The prepaid billing feature requires the RADIUS server to interface with a Prepaid Billing Server (PBS) to relay real-time billing information between the PDSN and the PBS. A third-party Prepaid Billing Server controls the real-time rating of data calls and maintains balances in users' accounts. Cisco does not supply the PBS.
The following three types of Prepaid service are available in PDSN Release 2.1:
•
•
•
Prepaid functionality is supported on PDSN for the following type of data sessions:
•
•
•
•
Prepaid service is also available for sessions opened with MSID-based authentication access.
Note
Volume-based accounting for prepaid flows other than VPDN will count the bytes present in the PPP payload. For VPDN flows, it will count the bytes present in the PPP packet including the PPP packet header. A session that has multiple flows can have some of the flows with prepaid data service enabled, each either Volume-based or Duration-based, while other flows may not be prepaid enabled.
Tariff-based prepaid service is also supported for volume-based prepaid data service on the PDSN. To support tariff-based prepaid service, the Prepaid Billing Server should have the following capabilities:
•
•
Restrictions for Prepaid Support in Cisco PDSN Release 2.1
•
•
•
•
Prepaid Billing
When a user performs Simple IP access with AAA authentication, or Mobile IP access with FA-CHAP, the Prepaid capable PDSN sends a RADIUS Access-Request message for Authentication and Authorization. The Prepaid capable PDSN informs the Billing Server of its own Prepaid capabilities by including a PPAC VSA in the RADIUS Access-Request message.
The Home RADIUS performs Authentication and Authorization procedures as usual. If the HAAA identifies that a user is a prepaid user from its user profile, the HAAA interfaces with the Billing Server to retrieve prepaid related information for the user, and passes on the prepaid related information in the Access Request message. The Billing Server performs prepaid authorization for the user. The prepaid authorization procedure at HAAA and Billing Server consists of the following steps:
•
•
•
When the Billing Server successfully authorizes the user as a valid prepaid user, it notifies the HAAA that it supports prepaid service based on volume, or duration, or both, depending on the configuration at the Billing Server and capabilities as indicated by the PDSN. The HAAA encodes the information in a PPAC VSA to the PDSN, and indicates that volume-based or duration-based prepaid (or both) service is supported by the Billing Server.
HAAA sends the authorization response to the Prepaid capable PDSN using RADIUS Access-Accept/Reject messages. The authorization response includes a PPAQ VSA in the same RADIUS Access-Accept message stating an initial quota, quota-id and a threshold value of the quota for the prepaid flow corresponding to the user.
When the PDSN sends on-line Access Request messages to HAAA for prepaid related functionality, it does not set the User-Password (= 2) field in the message, and normal RADIUS message authentication is set and performed with Message Authenticator. Currently, the User-Password is set in online Access Requests to the default value of "cisco".
If the PDSN does not receive the PPAC VSA from the HAAA in the initial RADIUS Access-Accept message, or the message is included but indicates that "Prepaid Accounting not used", the PDSN will release the user's prepaid flow if the RADIUS Access-Accept message includes a PPAQ VSA. The PDSN will send an Access Request to HAAA to return the quota allocated with Update-Reason VSA that indicates Client Service termination.
If the PDSN is capable of supporting prepaid service based on either volume or duration, then the PDSN will enable prepaid service for the flow based on the Billing server-indicated service that applies to the session in PPAC. If the Billing server also indicates that the PDSN can allocate either volume or duration, then the PDSN will enable prepaid service based on the type of quota (volume or duration) present in PPAQ from HAAA. If both types of quota are present in PPAQ, then prepaid flow is not opened on the PDSN.
If the PDSN is capable of supporting prepaid service based on volume, and Billing Server indicates that it will support prepaid service based on duration, then the PDSN will close the prepaid flow. The PDSN will send an Access Request message with Update-Reason VSA indicating "Client Service termination". The same logic applies to the PDSN if it supports prepaid based on duration, and Billing Server returns prepaid service based on volume.
If the PDSN receives an Access-Accept message containing the PPAC VSA indicating prepaid service supported, but the initial quota is not included in the message, the PDSN will close the flow. Since no quota was received in the Access Accept, the PDSN will not send further RADIUS Access Request message to HAAA.
To ignore Billing Server interaction of HAAA for Access Requests sent by the PDSN during mobile IP re-registration for FA-CHAP, the PDSN will include the Session-Continue VSA set to "TRUE" in the on-line Access Request messages.
If multiple flows are present for the session that hosted the Prepaid flow, and a prepaid flow was stopped, and if it was the last flow for the session, then the session will be deleted by the PDSN. If one of mobile IP flows expires and it is not the last flow for the session, then the PDSN will close the flow locally. If the resource revocation mechanism is enabled on PDSN, the relevant resource revocation mechanism will be applied in this case.
If the Simple IP (SIP) flow is closed (for example, a PPP session is torn down or quota for the SIP flow expires), then all the other mobile IP flows, both prepaid and non-prepaid, will also get closed. If SIP flow is closing due to allocated quota expiry, it will send Access Request message with Update-Reason as "Quota Reached". In other cases where the SIP session is closed, the Access Request will be sent with Update-Reason as "Client Service Termination". All other prepaid flows for the PPP session will also send Access Request messages to close the prepaid service and return unused quota. The Update-Reason for all these flows will contain value for "Main SI Released".
When threshold for the quota is reached, the PDSN sends an Access Request to HAAA to retrieve more quota for the flow. In case the values of threshold for the quota and the quota allocated are same, then on quota expiry (when Quota = Threshold), the PDSN will treat this as flow as closed, and send an Access Request with Update-reason as "Quota reached".
When the quota expires for the flow, the PDSN sends an on-line Access Request to the HAAA to indicate that the prepaid flow is released. During this time the PDSN marks the flow as deleted, and stops switching any packets for the flow. On receipt of the Access Accept from the AAA server for this Access Request, the PDSN deletes the prepaid flow for the user and sends an Accounting Stop.
If resource revocation mechanism is enabled at the PDSN, then the PDSN will send a resource revocation to the HA to clear binding at the HA, and the PDSN will clear the visitor info for the flow.
Upon receiving a RADIUS Disconnect Request (POD) or Mobile IP revocation messages, the PDSN will send an on-line RADIUS Access-Request message containing the used quota and the Update-Reason Sub-Type set to "Remote forced disconnect". The PDSN will delete the flow and send resource revocation message to the HA, and will send the existing RADIUS Accounting-Stop.
Volume-based Prepaid Data Service Flow
The metric for accounting volume based Prepaid service is total bytes flowing through the user flow in upstream and downstream direction.
Step 1
The PDSN includes its own PPAC VSA to inform the HAAA/Billing Server that it supports Prepaid based on Volume (value = 1 or 3). If resource revocation is enabled on the PDSN, then it will send a SessionTerminationCapability (STC) attribute indicating that it can support resource revocation for Mobile IP sessions.
The Home RADIUS server performs the regular Authentication and Authorization of the Access Request sent by the user. If the user profile indicates the user is a Prepaid subscriber, HAAA interfaces with the Billing Server, and provides the Billing Server with the prepaid info for the user as received in the Access Request message.
Step 2
The HAAA encapsulates the prepaid information received for the user in a RADIUS Access-Accept message and sends it to the PDSN. The RADIUS message includes:
•
–
–
–
•
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. The PDSN stores the information present in the packet regarding the quota allocated for the flow and the threshold corresponding to the allocated flow. It also stores the Quota-ID allocated in the user flow present in the message. Once the flow for the user comes up (IP address assigned for Simple IP, or MIP RRP received from the HA and sent to the MS), the PDSN starts metering the user's traffic over the flow against the allocated quota.
Step 3
Step 4
–
–
–
HAAA authenticates the RADIUS packet and if authentication is successful, forwards the prepaid-related information present in the packet to the Billing Server.
Step 5
The HAAA sends the information received from the Billing Server into a RADIUS Access-Accept message to be sent to PDSN. The attributes that are encapsulated into a PPAQ VSA include:
–
–
–
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. The PDSN stores the information present in the packet and updates the quota allocated for the flow and the current threshold value corresponding to the allocated flow. It also stores the new Quota-ID allocated for the current quota.
Step 6
Step 7
•
•
In this case, PDSN sends an Access-Request message containing the PPAQ VSA that includes:
–
–
At this time, the PDSN marks the prepaid flow as being marked for deleted, such that it does not switch any packets through it for the prepaid flow. It does not delete the prepaid flow immediately and waits for the response of the Access-Request or timeout of the Access-Request message.
Step 8
After the PDSN receives the Access Accept message, it deletes the user flow for the Prepaid session. As part of the usual off-line accounting procedures, the PDSN sends an off-line RADIUS Accounting-Stop message upon successful release of the appropriate resources (normal operation).
Duration-based Prepaid Data Service Flow
The metric for accounting duration-based Prepaid service is session duration in seconds.
Step 1
The Prepaid capable PDSN determines that Simple IP or Mobile IP setup requires a RADIUS Access-Request message to be sent to the Home RADIUS Server. For SIP sessions, user authentication has to be performed with AAA rather than local authentication. In the case of Mobile IP users, FA-CHAP is required for authentication.
The PDSN includes its own PPAC VSA to inform the HAAA/Billing Server that it supports Prepaid based on Duration (value = 2 or 3). If resource revocation is enabled on the PDSN, the PDSN will send a SessionTerminationCapability (STC) attribute indicating that it can support resource revocation for Mobile IP sessions. The Event_Time attribute (G4, value = 55) will be included in the RADIUS Access-Request message.
The Home RADIUS server performs the regular Authentication and Authorization of the Access Request sent by the user. If the user profile indicates the user is a Prepaid subscriber, the HAAA interfaces with the Billing Server and provides the Billing Server with the prepaid related info for the user as received in the Access Request message.
Step 2
The HAAA encapsulates the prepaid information received for the user in a RADIUS Access-Accept message and sends it to the PDSN. The RADIUS message includes:
A PPAQ VSA that contains the following parameters:
•
•
•
A PPAC VSA that indicates prepaid service is based on Volume.
For duration based Prepaid packet data service, the Event_Time attribute is used for DurationQuota/DurationThreshold allocation by the Billing Server.
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. The PDSN stores information in the packet regarding the quota allocated for the flow, and threshold corresponding to the allocated flow. It also stores the Quota-ID allocated corresponding to the quota.
Once the flow for the user comes up (for example, an IP address assigned for Simple IP or MIP RRP received from the HA and sent to the MS), the PDSN starts the timer corresponding to the duration threshold value and duration quota value.
Once the timer expires for the threshold value of the allocated quota for the prepaid flow, the PDSN sends an Access-Request Message to AAA to refresh quota for the prepaid flow. This Access Request message contains a PPAQ VSA, which includes following parameters:
•
•
•
The HAAA authorizes the RADIUS packet and, if successful, forwards the prepaid-related information in the packet to the Billing Server.
Step 3
The HAAA sends the information received from the Billing Server into a RADIUS Access-Accept message to be sent to the PDSN. The attributes that are encapsulated into a PPAQ VSA include:
•
•
•
After the PDSN receives the Access-Accept message from the AAA, it parses the RADIUS packet and retrieves the attributes inside it. The PDSN stores the information in the packet, updates it with the quota allocated for the flow and the current threshold value corresponding to the allocated flow. The PDSN restarts the duration quota timer with the new value received in the Accept-Accept message, and starts the threshold timer with the new threshold value received corresponding to the current quota. It also stores the new Quota-ID allocated for the current quota.
Step 4
•
•
If this event occurs, the PDSN sends an Access-Request message containing the PPAQ VSA that includes:
–
–
The PDSN marks the prepaid flow for deletion, and does not switch any packets through it for the prepaid flow. The PDSN does not delete the prepaid flow immediately, and waits for the response of the Access-Request or timeout of the Access-Request message.
Step 5
When the PDSN receives the Access Accept message, it clears the user flow for the Prepaid session. As part of the usual off-line accounting procedures, the PDSN sends an off-line RADIUS Accounting-Stop message upon successful release of the appropriate resources.
Volume-based Prepaid Data Service with Tariff Switching
The PDSN and Billing Server support tariff switch, volume- based, Prepaid packet data service. The tariff switch trigger is controlled at the Billing Server. To support this capability, a new sub-Type PrepaidTariffSwitch (PTS) VSA attribute is sent by HAAA to PDSN. This attribute contains following key sub-types:
•
•
•
The following sequence describes the functionality of Prepaid data service when Tariff Switching is enabled.
Step 1
PDSN includes its own PPAC VSA to inform the HAAA/Billing Server that it supports Prepaid based on Volume (value = 1 or 3). If resource revocation is enabled on the PDSN, then it will send a SessionTerminationCapability (STC) attribute indicating that it can support resource revocation for Mobile IP sessions.
The Home RADIUS server performs the regular Authentication and Authorization of the Access Request sent by the user. If the user profile indicates the user is a Prepaid subscriber, HAAA interfaces with the Billing Server and provides the Billing Server with the prepaid related info for the user as received in the Access Request message.
Step 2
The Billing Server that supports Tariff Switching indicates the time (in seconds) remaining for the next tariff switch point, and passes the info to the HAAA server. Optionally, it can include the time after tariff switch point that the PDSN will send Access Request to the HAAA if the threshold value for the assigned quota is not reached.
The HAAA encapsulates the prepaid information received for the user from Billing Server in a RADIUS Access-Accept message and sends it to the PDSN. The RADIUS message includes:
•
–
–
–
•
–
–
–
•
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. It stores the information present in the packet regarding the quota allocated for the flow and threshold corresponding to the allocated flow. The PDSN also stores the Quota-ID allocated in the user flow present in the message.
Once the flow for the user comes up (the IP address assigned for Simple IP, or MIP RRP received from the HA and sent to the MS), the PDSN starts metering user's traffic over the flow against the allocated quota. It also starts the timer corresponding to the value received in TariffSwitchInterval attribute so that it is aware when the tariff switch condition is hit. The timer is started by the PDSN only if the timestamp of the Access Request + Tariff Switch Interval is more than the timestamp of the Access Accept message.
QuotaId present in the PTS attribute should be equal to the QuotaId present inside PPAQ. If the 2 values are unequal, the prepaid flow is closed by PDSN.
Step 3
Step 4
•
•
•
The HAAA authorizes the RADIUS packet and if authorization is successful, forwards the prepaid-related information present in the packet to the Billing Server.
Step 5
The Billing Server also indicates to the HAAA, the time remaining in seconds for the next Tariff Switch trigger point.
The HAAA sends the information received from the Billing Server into a RADIUS Access-Accept message to be sent to the PDSN. The attributes that are encapsulated into a PPAQ VSA include:
•
•
•
The Attributes encapsulated inside PTS attribute includes:
•
•
•
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. It stores the information present in the packet updating with the quota allocated for the flow and the current threshold value corresponding to the allocated flow. It also stores the new Quota-ID allocated for the current quota.
Additionally, the PDSN re-starts the timer indicated in TariffSwitchInterval attribute. This time indicates the time remaining in seconds before the next tariff switch condition will be hit.
Step 6
Step 7
Step 8
Step 9
•
•
•
The PTS attribute contains following subtypes:
–
–
The HAAA authorizes the RADIUS packet and, if authorization is successful, forwards the prepaid-related information present in the packet to the Billing Server.
The Billing Server updates its database with the amount of quota utilized by the user. Since the user indicates quota renewal, the Billing Server apportions a fraction of prepaid account balance of the user. It also assigns a new Quota ID for the current allocated quota and a corresponding threshold value for the assigned quota. This information is passed on to the HAAA.
The Billing Server also indicates to the HAAA the time remaining in seconds for the next Tariff Switch trigger point.
The HAAA sends the information received from the Billing Server into a RADIUS Access-Accept message to be sent to PDSN. The attributes that are encapsulated into a PPAQ VSA include:
•
•
•
The PTS attribute contains following subtypes:
–
–
–
After the PDSN receives the Access-Accept message from AAA, it parses the RADIUS packet and retrieves the attributes inside it. The PDSN stores the information present in the packet, and updates it with the quota allocated for the flow and the current threshold value corresponding to the allocated flow. It also stores the new Quota-ID allocated for the current quota.
Additionally, the PDSN re-starts the timer indicated in TariffSwitchInterval attribute. The PDSN starts the timer only if the timestamp of the Access Request + Tariff Switch Interval is more than the timestamp of the Access Accept message. This time indicates the time remaining in seconds before the next tariff switch condition will be hit.
Support for G17 Attribute in Acct-Stop and Interim Records
The G17 attribute is required to bill users based on when the last activity was detected rather than when the user is de-registered. The following scenario gives a brief on how the attribute is used and how AAA needs to identify the last user activity.
G17 is defined as last user activity to indicate the time when the last activity was detected by the user. The G17 attribute is sent in acct-stop and interim accounting update messages, and has the following usage guidelines:
•
•
•
•
•
The G17 attribute is useful under the following conditions:
•
–
–
–
•
–
–
–
Home Area, Maximum Authorized Aggregate Bandwidth and Inter-user Priority Attributes Downloaded from AAA
The home-area, inter-user priority and maximum authorized aggregate bandwidth attributes are received by the PDSN, and are forwarded to the PCF as part of subscriber QoS profile (NVSE) structure. Local configurations of these attributes are not supported in PDSN 3.5.
The subscriber QoS profile is carried to the PCF in the following messages from the PDSN:
•
•
All of these attributes are synchronized to the standby in session redundancy
Basic Operation
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
–
–
•
•
Subscriber QoS Profile
Subscriber QoS profile consists of the following attributes that are downloaded from AAA:
•
•
•
These attributes are stored in the PDSN, and are forwarded to the PCF as part of subscriber QoS profile. The A11 registration reply, or A11 session-update, carries the subscriber QoS profile to PCF.
The subscriber QoS profile, carried in A11 messages to the PCF, is packed as an NVSE with the attributes as RADIUS VSAs.
Bandwidth Policing
During authentication of the mobile with the AAA, the maximum authorised aggregate bandwidth attribute may be downloaded from AAA as part of anaccess-accept. If this attribute is downloaded, the PDSN creates a policy internally and associates it with the session. The traffic to the mobile is then policed based on the value downloaded. When the session goes down, the policy is also removed.
Session Redundancy
The downloaded attributes are always synced to the standby PDSN using the existing Session Redundancy infrastructure whenever the flow is created, or during handoff.
When the switchover happens, the policing starts over in the newly active box because fresh tokens are allocated in the bucket.
Configuring Subscriber Qos Profile to PCF
To enable the PDSN to send Subscriber QoS profiles to the PCF through session updates, peform the following task:
Configuring Bandwidth Policing
To configure policing of down stream data traffic for the session, perform the following task:
Configuring VSAs in Subscriber QoS Profiles
To configure the sending of vendor specific attributes in Subscriber QoS Profile, perform the following task:
Note
Here is a sample configuration:
cdma pdsn virtual-template 1cdma pdsn a10 max-lifetime 65535cdma pdsn a10 ahdlc engine 0 usable-channels 8000cdma pdsn a10 police downstreamcdma pdsn a11 session-update qoscdma pdsn pcf 10.1.1.1 10.1.1.50 vendor-id 3729cdma pdsn timeout mobile-ip-registration 10cdma pdsn timeout a11-session-update 3cdma pdsn send-agent-advcdma pdsn debug show-conditionscdma pdsn secure pcf 150.1.4.1 spi 100 key ascii ciscocdma pdsn secure pcf 150.1.4.10 150.1.4.18 spi 100 key ascii ciscocdma pdsn secure pcf 150.1.4.25 spi 100 key ascii ciscocdma pdsn secure pcf 150.1.4.123 spi 100 key ascii ciscocdma pdsn secure pcf 150.1.4.223 spi 100 key ascii ciscocdma pdsn secure pcf 150.1.4.224 spi 100 key ascii ciscocdma pdsn compliance is835a handoffVerifying the Configuration
To verify that these various attributes are sent, perform the following tasks:
Here are some examples:
router# show cdma pdsnPDSN software version 3.5, service is enabledA11 registration-update timeout 1 sec, retransmissions 5Mobile IP registration timeout 10 secA10 maximum lifetime allowed 65535 secGRE sequencing is onMaximum PCF's limit set to 2000Maximum sessions limit not set (default 974 maximum)SNMP failure history table size 100MSID Authentication is disabledIngress address filtering is disabledSending Agent Adv in case of IPCP Address Negotiation is enabledAllow CI_ADD option during IPCP Phase is disabledAging of idle users disabledRadius Disconnect Capability enabledNumber of pcfs connected 0,Number of pcfs 3GPP2-RP 0,Number of sessions connected 0,Number of sessions 3GPP2-RP 0,Number of sessions Active 0, Dormant 0,Number of sessions using HDLCoGRE 0, using PPPoGRE 0router# show cdma pdsn sessionMobile Station ID IMSI 123456789123457PCF IP Address 5.1.1.46, PCF Session ID 1A10 connection time 119:19:10, registration lifetime 1800 secNumber of successful A11 re-registrations 357Remaining session lifetime 650 secAlways-On not enabled for the userCurrent Access network ID 0005-0101-2ELast airlink record received is Unknown, airlink is activeGRE protocol type is 0x8881GRE sequence number transmit 9, receive 7Using interface Virtual-Access2.1, status OPNUsing AHDLC engine on slot 0, channel ID 4381Service Option Ev-DOPolice Downstream CIR(bps) 8000,Normal Burst(bytes) 1500, Excess Burst(bytes) 3000Packets Conformed 0 Exceeded 0 Dropped packets 0This session has 1 flowSession Airlink State ActiveQoS Parameters:Max Aggregate Bandwidth: 8000Home Area : 10Inter User Priority : 15Flow service Simple, NAI NAI gSIP1@xxx.comMobile Node IP address 32.1.35.203Packets in 0, bytes in 0Packets out 0, bytes outrouter# show cdma pdsn statisticsBandwidth policing:Policing installed 0 failure 0 uninstalled 0Mobile IP Call Processing Per Second Improvements
In previous Cisco PDSN Releases, the Mobile IP CPS rate was approximately 40—comparatively low to that of Simple IP CPS which around 125. Mobile IP CPS was low because some of the Mobile IP configurations are interface specific. When these configurations are applied to the virtual-template interface (which is typical for the PDSN software), it takes considerable time to clone the virtual-access from the Virtual-Template because of the presence of the Mobile IP configuration, and this directly affects the CPS for Mobile IP service. The virtual-access are cloned when the calls are setup. To reduce virtual-access cloning time, PDSN Release 2.1 supports commonly used per-interface configurations in global configuration mode, and supports per-interface for backward compatibility.
Always On Feature
The PDSN supports Always On service to maintain the subscriber's packet data session in the local network. Always On support dictates that the PDSN will not release a subscriber's packet data session due to PPP idle timer expiry unless the PDSN determines the user is no longer reachable.
The Always On service maintains a subscriber's packet data session irrespective of PPP inactivity timer value for the user. At the same time, by making use of a finite PPP inactivity timer value, this feature provides a way to keep a session only as long as the user is reachable. The PDSN uses LCP Echos (as per rfc1661 and IS835B) to determine if the user is reachable.
Always On service is enabled for a user only when the F15 "Always On" attribute is received and set to a value of 1 in the access accept message from the AAA server.
The PDSN supports the ability to configure the Echo-Reply-Timeout timer and Echo-Request-Attempts counter. There is no extra configuration required on the PDSN to enable the Always On feature itself; however, you can disable the feature by configuring the Echo-Request-Attempts to 0. The PPP inactivity timer will be started for a session entering IPCP open state, if is configured or retrieved from AAA, for the user.
For always on users:
1.
2.
3.
4.
This feature is not supported for VPDN users, and is not applicable to Mobile IP users.
For Always-on users, a value of "1" will be sent for F15 attribute in the accounting start/stop/interim records. For non-always-on users, the F15 attribute will only be sent in the accounting records if configured.
Restrictions for the Always On Feature:
•
•
Basically it means even if there is upstream/downstream data received, the session will be teared down unless Echo-reply received within configured number of retries and configured time interval.
•
•
•
PDSN MIB Enhancement
The following sub-sections highlight the MIBs that are added in R3.0:
PPP Counters in Release 3.0
Objects have been added under the following existing MIB subgroups:
•
•
•
•
•
The below table describes the list of PPP counters that have been added in R3.0.
RP Counters in Release 3.0
The following list identifies new MIB subgroups in Release 3.0:
•
•
•
•
•
•
•
•
The following list identifies existing MIB subgroups, under which objects are added:
•
•
•
•
•
Table 6 indicates the additional RP counters supported in Release 3.0:
The following MIB enhancements are included in the Cisco PDSN Release 2.1:
PPP Counter Objects have been added under the following existing MIB subgroups:
•
•
•
•
•
In PDSN Release 2.1 a new MIB CISCO-CDMA-PDSN-CRP-MIB is defined to reflect the support of Closed RP interface on PDSN.
The MIB has two groups, SystemInfo and PerPCF Stats. SystemInfo group has the system level info like Total number of Closed RP sessions while the PerPCF stats group details call management statistics per PCF.
CDMA PDSN System Information
ccpcEnabled OBJECT-TYPE
"An indication of whether Closed RP feature is enabled."
::= { ccpcSystemInfo 1 }
ccpcSessionTotal OBJECT-TYPE
"The total number of Closed RP sessions currently established with this system."
::= { ccpcSystemInfo 2 }
CDMA PDSN Closed RP Registration Statistics per PCF
The PDSN PCF table maintains reference about the PCF in the RAN currently interacting with the PDSN.
An entry is created when an L2TP tunnel is established with the PCF. An entry is deleted when the tunnel is deleted.
Statistics Objects maintained per PCF include the following:
ccpcPcfIpAddressType OBJECT-TYPE
"Represents the type of the address specified by ccpcPcfIpAddress."
::= { ccpcPcfPerfStatsEntry 1 }
ccpcPcfIpAddress OBJECT-TYPE
"The IP address of the PCF that serves the mobile node."
::= { ccpcPcfPerfStatsEntry 2 }
ccpcPcfRcvdIcrqs OBJECT-TYPE
"Total number of Incoming-Call-Requests received to establish a L2TP session since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 3 }
ccpcPcfAcptdIcrqs OBJECT-TYPE
"Total number of Incoming-Call-Requests accepted since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 4 }
ccpcPcfDroppedIcrqs OBJECT-TYPE
"Total number of Incoming-Call-Requests denied since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 5 }
ccpcPcfSentIcrps OBJECT-TYPE
"Total number of Incoming-Call-Replies sent since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 6 }
ccpcPcfRcvdIccns OBJECT-TYPE
"Total number of Incoming-Call-Connected messages received since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 7 }
ccpcPcfAcptdIccns OBJECT-TYPE
"Total number of Incoming-Call-Connected messages accepted since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 8 }
ccpcPcfDroppedIccns OBJECT-TYPE
"Total number of Incoming-Call-Connected messages accepted since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 9 }
ccpcPcfRcvdCdns OBJECT-TYPE
"Total number of Call-Disconnect-Notify messages received to tear down L2TP session since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 10 }
ccpcPcfSentCdns OBJECT-TYPE
"Total number of Call-Disconnect-Notify messages sent to PCF to tear down L2TP session since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 11 }
ccpcPcfDroppedCdns OBJECT-TYPE
"Total number of Call-Disconnect-Notify messages dropped since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 12 }
ccpcPcfRcvdZlbs OBJECT-TYPE
"Total number of Zero-Length-Buffer messages received since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 13 }
ccpcPcfSentZlbs OBJECT-TYPE
"Total number of Zero-Length-Buffer messages sent since the L2TP tunnel was established with PCF."
::= { ccpcPcfPerfStatsEntry 14 }
In PDSN Release 2.0 and above, the MIB CISCO-CDMA-PDSN-MIB module is modified to provide the following statistics by PCF plus Service Option:
•
•
•
PCF/Service Option-based RP Statistics
In Release 1.2, the PDSN MIB provided RP registration statistics that offer box level information. These statistics are defined under the group "cCdmaRpRegStats." In Release 2.0 and above, in addition to box level information, the PCF/SO-based RP statistics will also be provided, and the MIB objects pertaining to these statistics is defined under the following group:
cCdmaPcfSoRpRegStats OBJECT IDENTIFIER
::= { cCdmaPerformanceStats 10 }
PCF/Service Option-based RP Update Statistics
The Release 1.2 MIB provides RP update statistics at box level; the MIB objects pertaining to these statistics are defined under the group cCdmaRpUpdStats. In addition to these statistics, the Release 2.0 MIB will provide PCF/SO based RP update statistics. These new MIB objects are defined under the following group.
cCdmaPcfSoRpUpdStats OBJECT IDENTIFIER
::= { cCdmaPerformanceStats 11 }
PCF/Service Option-based PPP Statistics
In Release 1.2, the MIB objected defined under the group "cCdmaPppStats" provides box level information about PPP negotiation between the PDSN and the MN. In Release 2.0, the MIB will provide the following PPP stats based on PCF/SO.
cCdmaPcfSoPppCurrentConns,
cCdmaPcfSoPppConnInitiateReqs,
cCdmaPcfSoPppConnSuccesses,
cCdmaPcfSoPppConnFails,
cCdmaPcfSoPppConnAborts
These objects are grouped under the following MIB group.
cCdmaPcfSoPppSetupStats OBJECT IDENTIFIER
::= { cCdmaPerformanceStats 12 }
As with previous releases, you can manage the Cisco PDSN with Cisco Works 2000 network management system using SNMP. In addition to the standard 6500 MIBS, the Cisco CDMA PDSN MIB (CISCO_CDMA_PDSN_MIB.my) is part of the PDSN solution. The Cisco PDSN MIB continues to support the following features:
•
–
–
–
–
–
•
–
–
Cisco Proprietary Prepaid Billing
PDSN Release 2.1 supports Cisco's proprietary prepaid billing features, that provide the following services:
•
•
•
Figure 7 shows the network reference architecture for prepaid service. The PBS resides in the mobile station's home network and is accessed by the home RADIUS server. A Cisco Access Registrar (AR) with prepaid functionality can be used as the home RADIUS server to provide service to prepaid and non-prepaid users.
Figure 7 PDSN Prepaid Billing Architecture
For roaming users, the local RADIUS server in the visited network forwards AAA requests to the home RADIUS server, using a broker RADIUS server if required. For roaming prepaid users, this requires that the local and broker AAA servers forward the new vendor specific prepaid accounting attributes transparently to the home RADIUS server.
In existing networks, where the home RADIUS server does not support the interface to the Prepaid Billing Server, AR can be placed in front of the home RADIUS server to act as a proxy. In this case AR forwards all authorization and accounting messages to /from the home RADIUS server and communicates with the PBS. This scenario is relevant if an operator already has a RADIUS server.
While this architecture does impose some additional requirements on the RADIUS server, the interface towards the PDSN does not change.
It is possible that an operator may want to use an existing WIN or IN based prepaid billing server. In this situation, the PBS will interface to the external prepaid billing server.
Accounting Records
The PDSN will continue to generate per flow accounting records in the same way as it does for non-prepaid users. However, the last Accounting Stop Request for a flow will contain the new prepaid Vendor Specific Attributes (VSAs) for reporting the final usage.
How Prepaid Works in PDSN
When a prepaid mobile user makes a data service call, the MS establishes a Point-to-Point Protocol (PPP) link with the Cisco PDSN. The Cisco PDSN authenticates the mobile station by communicating with the AAA server. The AAA server verifies that the user is a valid prepaid subscriber, determines what services are available for the user, and tracks usage for billing.
The methods used to assign an IP address and the nature of the connection are similar to those discussed in the "How PDSN Works" section on page 5.
The following sections describe the IP addressing and communication levels in the prepaid environment for each respective topic:
•
•
Prepaid Simple IP Call Flow
In the following scenario, the prepaid user has sufficient credit and makes a Simple IP data call. The user disconnects at the end of the call.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Prepaid Mobile IP Call Flow
In the following scenario, the prepaid user makes a Mobile IP data call. The user runs out of quota during the mobile IP data session and the PDSN disconnects the call. The call flow shows a single Mobile IP flow; however, additional flows are established and handled in a similar manner when the MS sends additional Mobile IP Registration Requests.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Step 14
Step 15
Note
3 DES Encryption
The Cisco PDSN include 3DES encryption, which supports IPSec on PDSN. IPSec on the MWAM platform requires you to use a Cisco VPN Acceleration Module.
This feature allows VPDN traffic and Mobile IP traffic (between the PDSN Home Agent) to be encrypted. In this release the PDSN requires you to configure the parameters for each HA before a mobile ip data traffic tunnel is established between the PDSN and the HA.
Note
Note
Mobile IP IPSec
The Internet Engineering Task Force (IETF) has developed a framework of open standards called IP Security (IPSec) that provides data confidentiality, data integrity, and data authentication between participating peers. IPSec provides these security services at the IP layer; it uses Internet Key Exchange (IKE) to handle negotiation of protocols and algorithms based on local policy, and to generate the encryption and authentication keys to be used by IPSec. IPSec can be used to protect one or more data flows between a pair of hosts, between a pair of security gateways, or between a security gateway and a host.
IS-835-B specifies three mechanisms for providing IPSec security:
•
•
•
Note
Hardware IPSec Acceleration Using IPSec Acceleration Module—Static IPSec
Note
IPSec-based security may be applied on tunnels between the PDSN and the HA depending on parameters received from Home AAA server. A single tunnel may be established between each PDSN-HA pair. It is possible for a single tunnel between the PDSN-HA pair to have three types of traffic streams: Control Messages, Data with IP-in-IP encapsulation, and Data with GRE-in-IP encapsulation. All Traffic carried in the tunnel will have the same level of protection provided by IPSec.
IS-835-B defines MobileIP service as described in RFC 2002; the Cisco PDSN provides Mobile IP service and Proxy Mobile IP service.
In Proxy Mobile service, the Mobile-Node is connected to the PDSN/FA through Simple IP, and the PDSN/FA acts as Mobile IP Proxy for the MN to the HA.
Once Security Associations (SAs, or tunnels) are established, they remain active until there is traffic on the tunnel, or the lifetime of the SAs expire.
Note
Conditional Debugging Enhancements
Trace Functionality in Release 3.0
While conditional debugging has been a useful tool to limit the displayed debugs to a particular user, the output can still be a bit misleading if a few users are traced together. Therefore, the following capabilities are added in R3.0:
•
–
–
–
–
–
–
–
–
–
–
–
•
Note
Note
Note
Note
Note
•
Enhancements Prior to Release 3.0
PDSN Release 2.1 supports additional conditional debugging for Mobile IP components. Mobile IP conditional debugging is supported based on NAI as well as the MN's home address.
Currently, when multiple conditional debugging is enabled, the debug output does not individually display the condition for which the debugs are printed for all the CDMA related debugs.
Check Condition
A condition is set using the debug condition username command.
Delete Condition
The debugging conditions can be removed using the following commands:
•
•
When a condition is removed using the above CLI, the IOS Conditional Debugging Subsystem, which maintains a list of conditions and the TRUE conditions, resets the flag. When all the conditions are removed, the debugging information will appear without any filter applied.
The PDSN software also utilizes conditional debugging based on the Mobile Subscriber ID (MSID) into the CDMA subsystem by using the existing IOS debug condition of the Cisco CLI. The calling option of the CLI is used to specify the MSID (for example, debug condition calling 00000000011124).
The following debug commands are supported for conditional debugging based on NAI. The NAI is a name like foo@bar.com.
•
•
•
The following debug commands are not impacted by NAI-based conditional debugging:
•
•
This release provides conditional debugging support for the following PDSN CLI commands:
•
•
•
•
•
The a11 debugs additionally support msid-based debugging using the following individual CLI commands:
•
•
•
Conditional debugging is an IOS feature, and the following CLI are available across all images.
router# debug condition ?application Applicationcalled called numbercalling callingglbp interface groupinterface interfaceip IP addressmac-address MAC addressmatch-list apply the match-liststandby interface groupusername usernamevcid VC IDThe options calling, username, and ip are used by the CDMA/Mobile IP subsystems.
PDSN#debug condition username ?WORD Username for debug filteringPDSN#debu condition calling ?WORD Calling numberPDSN#debu condition ip ?A.B.C.D IP addressRefer to the debug commands in the Command Reference for more information about conditional debugging in PDSN Release 2.1.
Electronic Serial Number (ESN) in Billing
The ESN is a unique identifier for a piece of equipment, such as of a mobile device, and is used during the authentication process. The ESN is parameter a2 of the R-P Session Setup airlink record, and parameter A2 in the PDSN Usage Data Record (UDR). Both parameters are introduced in this release.
The PDSN accepts the parameter a2, and puts it as A2 into a User Data Record.
This feature is supported in the Cisco Access Registrar.
Support for Mobile Equipment Indentifier (MEID)
The MEID is a new attribute introduced in IS-835D, and will eventually replace the ESN AVP. In the interim period, both attributes are supported on the PDSN.
To include the MEID in Access Request, FA-CHAP, or Mobile IP RRQ, use the cdma pdsn attribute send a3 command.
1xEV-DO Support
The Cisco PDSN supports Evolution-Data Optimized (1xEV-DO). 1xEV-DO offers high performance, high-speed, high-capacity wireless Internet connectivity, and is optimized for packet data services. It can transport packet data traffic at forward peak rates of 2.4 Mbps, which is much higher than the current 1xRTT peak rate of 144 kbps.
PDSN support for 1xEV-DO technology includes the following enhancements:
•
•
Integrated Foreign Agent (FA)
The FA is an essential component to mobility, because it allows a mobile station to remotely access services provided by the station's home network. The Cisco PDSN provides an integrated FA. The FA communicates with any standard HA including the Cisco IOS-based HA.
AAA Support
The Cisco PDSN provides an authentication client that communicates with any standard AAA server, including Cisco Access Registrar, to authenticate the mobile station. It uses the mobile stations' name (NAI) for authentication of the user with the local AAA server.
•
–
–
–
Note
•
–
–
•
–
–
–
•
–
–
–
–
The Cisco PDSN also supports service provisioning using AAA servers and a user service profile. This profile is defined by the user's home network. It is referenced by the NAI. It is typically stored in the AAA server in the user's home network, along with the user authentication information, and is retrieved as part of authorization reply.
Packet Transport for VPDN
The Cisco PDSN supports the transport of VPDN packets. If the operator offers VPDN services, the mobile station can securely access private resources through a public Internet or dedicated links. The VPDN tunnel extends from the PDSN/FA to the home IP network. The home IP network is the IP network associated with the NAI.
Proxy Mobile IP
With Proxy Mobile IP as part of the PPP link initiation, the PDSN registers with a HA on behalf of the mobile station. It obtains an address from the HA and forwards that address to the mobile station as part of IPCP during PPP initialization.
Multiple Mobile IP Flows
The Cisco PDSN allows multiple IP access points from the same mobile station, as long as each IP flow registers individually (each IP flow requires a unique NAI). This enables multiple IP hosts to communicate through the same mobile access device and share a single PPP connection to the operator's network. For accounting purposes, it is important that the PDSN generate separate usage data records (UDRs) for each flow to the AAA server.
Redundancy and Load Balancing
This section provides information about Intelligent PDSN Selection and Load Balancing for the Controller - Member cluster model.
PDSN Cluster Controller / Member Architecture
The PDSN Controller member architecture was designed to support 8 members with redundant Active/Standby controllers. This controller-member mode designates certain nodes as controllers responsible for performing PDSN selection, and for maintaining the global session tables. Each member node maintains information only about the sessions that are terminated on that node. Controllers can be redundant with all session information synchronized between them, and they monitor the state of all nodes to detect the failure of a member or another controller.
When a PDSN cluster operates in the controller-member mode, controllers are dedicated to the PDSN selection function, and do not terminate bearer sessions.
PDSN Release 2.1 supports the following enhancements:
•
•
•
•
When a Registration Request (RRQ) arrives from the PCF to the active controller, the controller uses the MSID as an index to look up the session-table. If a session record entry is present, the controller forwards the RRQ to the PDSN that hosts the session for the MSID. If the session entry is not present in the controller session-table, the controller chooses a member based on a configured selection algorithm, and replies to the PCF with an RRP that suggests the member IP address in the message.
When the session comes up, the member sends a Session-Up message from the member for that session (MSID) to the controller. On receipt of this message from the member, the controller creates the Session Record for that MSID in the controller to establish MSID-member association on the controller. On receipt of Session-Down message from member, the controller flushes the Session Record from the controller.
The controller does not create a Session Record for the MSID when it redirects the RRQ, but only on the receipt of a Session-Up message from the member on which the session has come up
To support a large number of members (28~48) per Controller, processing overhead is reduced when members send one bulk-update packet to the controller for every configured periodic update time interval with multiple pairs of Session-Up/Session-Down. The packet contains concatenated multiple MSIDs with one Session-Up/Session-Down flag, thereby saving bytes in the packet. The controller will process these bulk-update packets and send a bulk-update-ack packet to the members.
Conditional Debugging Support Under Clustering Feature
The Cisco PDSN 2.0 Clustering feature adds additional support for the conditional debugging with the following clustering debug command on both controller and member:
•
Note
PDSN Controller-Member Clustering
In Controller-Member clustering, a controller maintains load and session (such as A10 connection) information for each member in the cluster, and performs member selection for load-balancing or inter-PDSN handoff avoidance. The controller identifies the operational state of each member and detects the failure of a member, or the failure of another controller. A member notifies the controller about its load and session information.
Note
Figure 8 illustrates the Controller-Member architecture on the 6500 or 7600-based MWAM platform. This illustration depicts two PDSN clusters with two primary and two backup controllers, and their corresponding members.
Figure 8 PDSN Controller -Member Architecture for MWAM on the Catalyst 6500
PDSNs that are designated as controllers, perform member PDSN selection and load balancing. The following list describes the major functions of the controllers:
•
•
•
•
•
•
•
Redundancy
Cluster redundancy is based on the premise that only one PDSN might fail at any given time. Two controllers are configured as an HSRP group: One controller is active, the other standby. Controllers have redundancy and members have load sharing.
Load Sharing
Cluster member loadsharing is an N+1 scheme. If a member fails, the established sessions will be lost, but the overall group capacity allows sessions to be re-established with the other group members. Additionally, redundancy is also enhanced because cluster members no longer have to be network neighbors.
Controllers exchange information over an ethernet link. Controllers and members exchange information over a unicast interface link where members address messages to the HSRP group address of the controllers. The members in a PDSN cluster do not need to be network neighbors; they can be attached anywhere in the IP network.
Adding an additional controller to a cluster is simplified by auto-configuration of the controller in the cluster. This is possible by configuring the additional controller for HSRP. The newly-added controller will automatically synchronize with the active controller. Similarly, when a new member is added to the cluster, auto-configuration for the member occurs in all cluster controllers.
PDSN Cluster Member Selection
Selection of a cluster member by the controller is based on a load factor. Load factor is a computed value by session load and CPU load on a member. The controller attempts to assign sessions to a member that has smallest load factor so that data connections are evenly distributed over members in the cluster as much as possible.
If an A11 Registration Request is received indicating a handoff, a member that is already serving the session is selected by the controller.
Load Balancing
A controller maintains load information for all members in the cluster in order to perform PDSN Cluster Member selection. This load information is transferred from the members to the controller under the following conditions:
•
•
•
The session and member records are synchronized between the active and standby controllers as needed. Since both active and standby controller maintain session and load information for all the members of that cluster, failure of a controller does not result in the loss of any session or load information.
Upgrading the Controller PDSN Software from R1.2 to R2.0
To upgrade the PDSN controller to Release 2.0, perform the following tasks:
Step 1
Step 2
# show cdma pdsn cluster controller configuration
Step 3
config# cdma pdsn cluster controller member periodic-update
Follow the same procedure as above to upgrade the other PDSN controller to Release 2.0.
Upgrading the Member PDSN Software from R1.2 to R2.0 and Above
To upgrade a member PDSN to Release 2.0 or 2.1, perform the following tasks:
Step 1
config# cdma pdsn cluster member prohibit administratively
The status of the member will be updated to the controller in a subsequent periodic keepalive reply message that the member sends to the controller. The controller, upon reception of this message, does not select this member for any of the new incoming calls.
Step 2
#show cluster controller member prohibited administratively
The calls, which are already connected to the member, will be alive until the mobile node disconnects the call. Alternatively, the calls can be forcibly cleared on the prohibited member using the following command:
#clear cdma pdsn session all
Step 3
config# no cdma pdsn cluster member prohibit administratively
Once the controller is updated with the status the new member PDSN will be selected for new incoming calls.
Step 4
config# cdma pdsn cluster member periodic-update 300
Scalability
In this release the PDSN uses a new scalability feature that allows PPP sessions to run on virtual-access subinterfaces that can support up to 20000 sessions.
Note
Note
Note
High Availability
Overview
High availability allows you to minimize the switchover time from the active supervisor engine to the standby supervisor engine if the active supervisor engine fails.
Prior to this feature, fast switchover ensured that a switchover to the standby supervisor engine happened quickly. However, with fast switchover, because the state of the switch features before the switchover was unknown, you had to re-initialize and restart all the switch features when the standby supervisor engine assumed the active role.
High availability removes this limitation; high availability allows the active supervisor engine to communicate with the standby supervisor engine, keeping feature protocol states synchronized. Synchronization between the supervisor engines allows the standby supervisor engine to take over in the event of a failure.
In addition, high availability provides a versioning option that allows you to run different software images on the active and standby supervisor engines.
For high availability, a system database is maintained on the active supervisor engine and updates are sent to the standby supervisor engine for any change of data in the system database. The active supervisor engine communicates and updates the standby supervisor engine when any state changes occur, ensuring that the standby supervisor engine knows the current protocol state of supported features. The standby supervisor engine knows the current protocol states for all modules, ports, and VLANs; the protocols can initialize with this state information and start running immediately.
The active supervisor engine controls the system bus (backplane), sends and receives packets to and from the network, and controls all modules. Protocols run on the active supervisor engine only.
The standby supervisor engine is isolated from the system bus and does not switch packets. But it does receive packets from the switching bus to learn and populate its Layer 2 forwarding table for Layer 2-switched flows. The standby supervisor engine also receives packets from the switching bus to learn and populate the Multilayer Switching (MLS) table for Layer 3-switched flows. The standby supervisor engine does not participate in forwarding any packets and does not communicate with any modules.
If you enable high availability when the standby supervisor engine is running, image version compatibility is checked and if found compatible, the database synchronization starts. High availability compatible features continue from the saved states on the standby supervisor engine after a switchover.
When you disable high availability, the database synchronization is not done and all features must restart on the standby supervisor engine after a switchover.
If you change high availability from enabled to disabled, synchronization from the active supervisor engine is stopped and the standby supervisor engine discards all current synchronization data.
If you change high availability from disabled to enabled, synchronization from the active to standby supervisor engine is started (provided the standby supervisor engine is present and its image version is compatible).
NVRAM synchronization occurs irrespective of high availability being enabled or disabled (provided there are compatible NVRAM versions on the two supervisor engines).
If you do not install a standby supervisor engine during system bootup, the active supervisor engine detects this and the database updates are not queued for synchronization. Similarly, when you reset or remove the standby supervisor engine, the synchronization updates are not queued and any pending updates in the synchronization queue are discarded. When you hot insert or restart a second supervisor engine that becomes the standby supervisor engine, the active supervisor engine downloads the entire system database to the standby supervisor engine. Only after this global synchronization is completed, the active supervisor engine queues and synchronizes the individual updates to the standby supervisor engine.
Note
For more information about High Availability, including configuration details, and information about power management, refer to the "PDSN Controller-Member Clustering" section on page 106, as well as the documents at the following urls:
•
–
•
–
–
Related Features and Technologies
•
•
•
•
•
Related Documents
For additional information about the Cisco PDSN Release 2.1 software, refer to the following documents:
•
For more information about:
•
•
•
•
•
•
Supported Platforms
The Cisco PDSN for MWAM release is a feature enhancement for the Multi-Processor WAN Application Module (MWAM) card that resides on the Cisco Catalyst 6500 switch or Cisco 7600 Internet Router. Refer to the following document for more information regarding the respective platforms:
•
Supported Standards, MIBs, and RFCs
Standards
•
•
•
MIBs
•
•
•
•
•
•
•
•
For descriptions of supported MIBs and how to use MIBs, see the Cisco MIB web site on CCO at http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.
RFCs
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Configuration Tasks
This section describes the steps for configuring the Cisco PDSN software on the MWAM platform. Prior to configuring instances of the PDSN on MWAM application cards, you must create a base Catalyst 6500 or 7600 configuration. Refer to the Cisco Multi-processor WAN Application Module Installation and Configuration Note for more information.
System Requirements
This section describes the system requirements for Cisco IOS Release 12.4(15)XM:
•
•
•
•
•
•
Memory Requirements
Table 7 shows the memory requirements for the PDSN Software Feature Set that supports the Cisco 7206VXR router, the MWAM card on the Cisco 6500 Catalyst Switch platform and 7600 Internet router platform, and the Cisco NPE-G1 router. The table also lists the memory requirements for the IP Standard Feature Set (for the Home Agent [HA]).
Hardware Supported
Cisco PDSN 3.5 release will be a special release that is developed on Cisco IOS 12.4 for the MWAM card on the Cisco 6500 Catalyst Switch platform and 7600 Internet router platform, and the Cisco NPE-G1 router.
A Hardware-Software Compatibility Matrix is available on CCO for users with CCO login accounts. This matrix allows users to search for supported hardware components by entering a Cisco platform and IOS Release. The Hardware-Software Compatibility Matrix tool is available at the following URL:
http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi
Software Compatibility
Cisco PDSN 3.5 release will be a special release that is developed on Cisco IOS 12.4.
Cisco PDSN 3.5 supports the same features that are in Cisco IOS Release 12.4, with the addition of the PDSN Release 3.5 feature.
Note
Determining the Software Version
To determine the version of Cisco IOS software running on your router, log in to the router and enter the show version EXEC command:
Router#show versionmwt5-6509a-06-4#sh verCisco IOS Software, MWAM Software (MWAM-C6IS-M), Version 12.3(11)YF4, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by Cisco Systems, Inc.Compiled Mon 25-Jul-05 15:24 by ssearchROM: System Bootstrap, Version 12.2(11)YS2 RELEASE SOFTWAREmwt5-6509a-06-4 uptime is 2 hours, 9 minutes System returned to ROM by reload at 07:35:31 UTC Wed Jul 6 2005 System restarted at 02:31:05 UTC Tue Jul 26 2005 System image file is "svcmwam-c6is-mz"Cisco MWAM (MWAM) processor with 473088K/32768K bytes of memory.SB-1 CPU at 700MHz, Implementation 1025, Rev 0.2Last reset from power-on1 Gigabit Ethernet interface511K bytes of non-volatile configuration memory.Configuration register is 0x4mwt5-6509a-06-4#Upgrading to a New Software Release
For information on upgrading to a new software release, see the product bulletin Cisco IOS Software Upgrade Ordering Instructions located at:
http://www.cisco.com/warp/public/cc/pd/iosw/prodlit/957_pp.htm
Upgrading PDSN Image from YF-based Image to R3.0-based Image
If you are upgrading the PDSN from a YF-based image to a R3.0-based image, you first need to upgrade the SUP image from a SXB-based image to the recommended SXE-based image.
Note
For more information on the 12.2(18)SXE3 Supervisor image, please refer to the following URL: http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_note09186a00801c8339.html
After you upgrade the SUP image, you can then upgrade the PDSN image.
Upgrading the Supervisor Image:
To upgrade the Supervisor image, perform the following procedure:
Step 1
Step 2
boot system disk0:s72033-advipservicesk9_wan-mz.122-18.SXE3.bin
Note
Step 3
Step 4
Both active and standby SUP will reload simultaneously and come up with the SXE3-based image.
Note
Upgrading the PDSN Image on MWAM:
To upgrade an image on the Cisco MWAM, you will need a compact flash card that has the MP partition from the current image or later, and a recent supervisor image. To locate the images, please go to the Software Center at Cisco.com (http://www.cisco.com/public/sw-center/)
Upgrading the Controller PDSN on MWAM:
To upgrade to the R3.0-based image on the PDSN controller, perform the following procedure:
Step 1
Log onto the supervisor and boot the MP partition on the PC.
SUP-PDSN#hw-module module 8 reset cf:1Device BOOT variable for reset = <cf:1>Warning: Device list is not verified.Proceed with reload of module?[confirm]% reset issued for module 8SUP-HA#SUP-HA#Nov 10 18:01:29.624: %SNMP-5-MODULETRAP: Module 8 [Down] TrapNov 10 18:01:29.624: SP: The PC in slot 8 is shutting down. Please wait ...Nov 10 18:01:55.252: SP: PC shutdown completed for module 8Nov 10 18:01:55.256: %C6KPWR-SP-4-DISABLED: power to module in slot 8 set off (Reset)Nov 10 18:04:00.195: SP: OS_BOOT_STATUS(8) MP OS Boot Status: finished bootingNov 10 18:04:42.299: %SNMP-5-MODULETRAP: Module 8 [Up] TrapNov 10 18:04:42.271: %DIAG-SP-6-BYPASS: Module 8: Diagnostics is passedNov 10 18:04:43.143: %OIR-SP-6-INSCARD: Card inserted in slot 8, interfaces are now onlineSUP-PDSN#Step 2
copy tftp: tftp file location pclc# linecard #-fs:
The upgrade file uses a special format that makes this process slow. The following example illustrates the upgrade process output:
SUP-PDSN#$/10.77.155.10/pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005 pclc#8-fs:Destination filename [c6svc5fmwam-h1is-mz.R30_11092005]?Accessing tftp://10.77.155.10/pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005...Loading pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005 from 10.77.155.10 (via Vlan10): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!![OK - 24168088 bytes]24168088 bytes copied in 192.376 secs (125629 bytes/sec)SUP-PDSN#Nov 10 18:09:03.903: %SVCLC-SP-5-STRRECVD: mod 8: <Application upgrade has started>Nov 10 18:09:03.903: %SVCLC-SP-5-STRRECVD: mod 8: <Do not reset the module till upgrade completes!!>Nov 10 18:09:42.022: %SVCLC-SP-5-STRRECVD: mod 8: <Application upgrade has succeeded>Nov 10 18:09:42.022: %SVCLC-SP-5-STRRECVD: mod 8: <You can now reset the module>SUP-PDSN#Step 3
SUP-PDSN#hw-module module 8 reset cf:4Device BOOT variable for reset = <cf:4>Warning: Device list is not verified.Proceed with reload of module?[confirm]% reset issued for module 8SUP-PDSN#Nov 10 18:10:34.831: %SNMP-5-MODULETRAP: Module 8 [Down] TrapNov 10 18:10:34.831: SP: The PC in slot 8 is shutting down. Please wait ...Nov 10 18:10:57.387: SP: PC shutdown completed for module 8Nov 10 18:10:57.391: %C6KPWR-SP-4-DISABLED: power to module in slot 8 set off (Reset)Nov 10 18:12:13.370: SP: OS_BOOT_STATUS(8) MWAMNov 10 18:14:30.447: %SNMP-5-MODULETRAP: Module 8 [Up] TrapNov 10 18:14:30.434: %DIAG-SP-6-BYPASS: Module 8: Diagnostics is passedNov 10 18:14:31.293: %OIR-SP-6-INSCARD: Card inserted in slot 8, interfaces are now onlineStep 4
7600a-cont2# show cdma pdsn cluster controller member loadSecs until Seq seeks Member(past) seek no reply IPv4 Addr State Load Sessions-------------------------------------------------------------------2 0 20.20.10.2 ready 0 158 0 20.20.10.1 ready 0 15-------------------------------------------------------------------Controller IPv4 Addr 20.20.101.1057600a-cont2# show cdma pdsn cluster controller session count30 session recordsStep 5
Step 6
Step 7
7600a-cont1#show cdma pdsn cluster controller member loadSecs until Seq seeks Member(past) seek no reply IPv4 Addr State Load Sessions-------------------------------------------------------------------2 0 20.20.10.2 ready 0 158 0 20.20.10.1 ready 0 15-------------------------------------------------------------------Controller IPv4 Addr 20.20.101.1057600a-cont1# show cdma pdsn cluster controller session count30 session records
Note
Note
Note
Upgrading the Member PDSN on MWAM:
To upgrade to the R3.0-based image on the PDSN, perform the following procedure:
Step 1
7600a-pdsn1(config)# cdma pdsn cluster member prohibit administrativelyThe calls, which are already connected to the member, will be alive until the mobile node disconnects the call. Alternatively, the calls can be forcibly cleared on the prohibited member using the following command:
7600a-pdsn1(config)# clear cdma pdsn session allStep 2
Log onto the supervisor and boot the MP partition on the PC.
SUP-PDSN# hw-module module 8 reset cf:1Device BOOT variable for reset = <cf:1>Warning: Device list is not verified.Proceed with reload of module?[confirm]% reset issued for module 8SUP-HA#SUP-HA#Nov 10 18:01:29.624: %SNMP-5-MODULETRAP: Module 8 [Down] TrapNov 10 18:01:29.624: SP: The PC in slot 8 is shutting down. Please wait ...Nov 10 18:01:55.252: SP: PC shutdown completed for module 8Nov 10 18:01:55.256: %C6KPWR-SP-4-DISABLED: power to module in slot 8 set off (Reset)Nov 10 18:04:00.195: SP: OS_BOOT_STATUS(8) MP OS Boot Status: finished bootingNov 10 18:04:42.299: %SNMP-5-MODULETRAP: Module 8 [Up] TrapNov 10 18:04:42.271: %DIAG-SP-6-BYPASS: Module 8: Diagnostics is passedNov 10 18:04:43.143: %OIR-SP-6-INSCARD: Card inserted in slot 8, interfaces are now onlineSUP-PDSN#Step 3
copy tftp: tftp file location pclc# linecard #-fs:The upgrade file uses a special format that makes this process slow. The following example illustrates the upgrade process output:
SUP-PDSN#$/10.77.155.10/pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005 pclc#8-fs:Destination filename [c6svc5fmwam-h1is-mz.R30_11092005]?Accessing tftp://10.77.155.10/pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005...Loading pdsn/images/c6svc5fmwam-h1is-mz.R30_11092005 from 10.77.155.10 (via Vlan10): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!![OK - 24168088 bytes]24168088 bytes copied in 192.376 secs (125629 bytes/sec)SUP-PDSN#Nov 10 18:09:03.903: %SVCLC-SP-5-STRRECVD: mod 8: <Application upgrade has started>Nov 10 18:09:03.903: %SVCLC-SP-5-STRRECVD: mod 8: <Do not reset the module till upgrade completes!!>Nov 10 18:09:42.022: %SVCLC-SP-5-STRRECVD: mod 8: <Application upgrade has succeeded>Nov 10 18:09:42.022: %SVCLC-SP-5-STRRECVD: mod 8: <You can now reset the module>SUP-PDSN#Step 4
SUP-PDSN#hw-module module 8 reset cf:4Device BOOT variable for reset = <cf:4>Warning: Device list is not verified.Proceed with reload of module?[confirm]% reset issued for module 8SUP-PDSN#Nov 10 18:10:34.831: %SNMP-5-MODULETRAP: Module 8 [Down] TrapNov 10 18:10:34.831: SP: The PC in slot 8 is shutting down. Please wait ...Nov 10 18:10:57.387: SP: PC shutdown completed for module 8Nov 10 18:10:57.391: %C6KPWR-SP-4-DISABLED: power to module in slot 8 set off (Reset)Nov 10 18:12:13.370: SP: OS_BOOT_STATUS(8) MWAMNov 10 18:14:30.447: %SNMP-5-MODULETRAP: Module 8 [Up] TrapNov 10 18:14:30.434: %DIAG-SP-6-BYPASS: Module 8: Diagnostics is passedNov 10 18:14:31.293: %OIR-SP-6-INSCARD: Card inserted in slot 8, interfaces are now onlineStep 5
7600a-pdsn1(config)# no cdma pdsn cluster member prohibit administratively
Note
Note
Changing Configuration on R3.0 PDSN in a Live Network:
If you need to change the working configuration on a PDSN in a live network environment, perform the following procedure:
Step 1
7600a-Stdy(config)# no cdma pdsn redundancyStep 2
Step 3
Step 4
Step 5
7600a-Stdy#show standby briefP indicates configured to preempt.|Interface Grp Prio P State Active Standby Virtual IPGi0/0.101 300 110 Standby 20.20.101.10 local 20.20.101.1017600a-Stdy# show cdma pdsn redundancyCDMA PDSN Redundancy is enabledCDMA PDSN Session Redundancy system statusPDSN state = STANDBY HOTPDSN-peer state = ACTIVECDMA PDSN Session Redundancy StatisticsLast clearing of cumulative counters neverTotal CurrentSynced from active ConnectedSessions 15 15SIP Flows 15 15MIP Flows 0 0PMIP Flows 0 07600a-Stdy#show redundancy inter-deviceRedundancy inter-device state: RF_INTERDEV_STATE_STDBYScheme: StandbyGroupname: pdsn-rp-sr1 Group State: StandbyPeer present: RF_INTERDEV_PEER_COMMSecurity: Not configured7600a-Stdy#show redundancy statesmy state = 8 -STANDBY HOTpeer state = 13 -ACTIVEMode = DuplexUnit ID = 0Split Mode = DisabledManual Swact = EnabledCommunications = Upclient count = 9client_notification_TMR = 30000 millisecondsRF debug mask = 0x07600a-Stdy#Step 6
Note
Step 7
Note
Note
Loading the IOS Image to the MWAM
The image download process automatically loads an IOS image onto the three Processor complexes on the MWAM. All three complexes on the card run the same version of IOS, so they share the same image source. The software for MWAM bundles the images it needs in flash memory on the PC complex. For more information, refer to the Cisco Multi-processor WAN Application Module Installation and Configuration Note.
Limitations
There are specific limitations and restrictions when loading an IOS image on the MWAM; please find them at the following URL: http://www.cisco.com/en/US/products/sw/iosswrel/ps5413/prod_release_note09186a00803b8dd5.html#wp70466
Configuring the PDSN Image
The Cisco PDSN can provide four classes of user services: Simple IP, Simple IP with VPDN, Mobile IP, and proxy Mobile IP. The following sections describe the configuration tasks for implementing Cisco PDSN. Each category of tasks indicates whether the tasks are optional or required.
R-P Interface Configuration Tasks (Required for all classes of user services)
The following tasks establish the R-P interface, also referred to as the A10/A11 interface.
To configure the R-P interface, complete the following tasks:
•
•
•
•
•
User Session Configuration Tasks (Optional)
To configure the user session, complete the following task.
•
Session Redundancy Configuration Tasks
To configure Session Redundancy on the PDSN, complete the following tasks:
•
•
•
•
•
•
AAA and RADIUS Configuration Tasks (Required for All Scenarios)
To configure the AAA and RADIUS in the PDSN environment, complete the following tasks.
•
•
Prepaid Configuration Tasks
•
VPDN Configuration Tasks (Required for Simple IP with VPDN Scenario)
To configure the VPDN in the PDSN environment, complete the following task:
•
Mobile IP Configuration Tasks (Required for Mobile IP)
To configure Mobile IP on the PDSN, complete the following task:
•
•
•
PDSN Selection Configuration Tasks (Optional)
To configure PDSN selection, complete the following tasks:
•
•
Network Management Configuration Tasks (Required for Network Management in Any Scenario)
To configure network management, complete the following task:
•
Other Configuration Tasks
The following tasks are optional on the PDSN:
•
•
•
•
•
•
•
•
•
•
•
Tuning, Verification, and Monitoring Tasks (Optional)
To tune, verify, and monitor PDSN elements, complete the following tasks:
•
Enabling PDSN Services
To enable PDSN services, use the following commands in global configuration mode:
Creating the CDMA Ix Interface
To create the CDMA Ix interface, use the following commands in global configuration mode:
Creating a Loopback Interface
We recommend that you create a loopback interface and then associate the loopback interface IP address to the virtual template, rather than directly configuring an IP address on the virtual template.
To create a loopback interface, use the following commands in global configuration mode:
Creating a Virtual Template Interface and Associating It With the PDSN Application
Creating a virtual template interface allows you to establish an interface configuration and apply it dynamically.
To create a virtual template interface that can be configured and applied dynamically, use the following commands in global configuration mode:
Enabling R-P Interface Signaling
To enable the R-P interface signaling, use the following commands in global configuration mode:
Configuring User Session Parameters
To configure user session parameters, use the following commands in global configuration mode:
Configuring PDSN Session Redundancy Infrastructure
The PDSN-SR feature uses the Cisco IOS Check-point Facility (CF) to send stateful data over Stream Control Transmission Protocol (SCTP) to a redundant PDSN. Additionally, in conjunction with Cisco IOS HSRP, the PDSN uses the Cisco IOS Redundancy Facility (RF) to monitor and report transitions on Active and Standby PDSNs.
Before configuring PDSN-SR, you need to configure the inter-device redundancy infrastructure.
Configuring HSRP
The Hot Standby Router Protocol (HSRP) provides high network availability because it routes IP traffic from hosts on networks without relying on the availability of any single router. HSRP is used in a group of routers for selecting an Active router and a Standby router. HSRP monitors both the inside and outside interfaces so that if any interface goes down, the whole device is deemed to be down and the Standby device becomes active and takes over the responsibilities of an Active device.
When configuring HSRP, note that the following recommendation and restrictions apply:
•
–
–
–
–
Note
•
Note
•
Use the same group number for each PDSN follow group as is defined for the primary group. Using the same group number for the primary and follow groups facilitates HRSP group setup and maintenance in an environment that contains a large number of PDSN interfaces and HRSP groups.
More information on HSRP configuration and HSRP groups can be found here:
http://www.cisco.com/en/US/partner/tech/tk648/tk362/tk321/tsd_technology_support_sub-protocol_home.html
and
http://www.cisco.com/en/US/partner/tech/tk648/tk362/technologies_configuration_example09186a0080094e90.shtml
Enabling HSRP and Configuring an HSRP Master Group
To enable HSRP on an interface and configure the primary group, use the following commands in interface configuration mode:
Configuring Follow Groups
HSRP follow groups are configured to share the HSRP parameters of the primary group by defining a follow group on the interface using the standby interface configuration command with the follow keyword option specified. Interfaces that share a group track states together and have the same priority.
To configure an interface to follow a primary group, use the following commands in interface configuration mode:
Enabling Inter-Device Redundancy
To enable inter-device redundancy, use the following commands beginning in global configuration mode:
Configuring the Inter-Device Communication Transport
Inter-device redundancy requires a transport for communication between the redundant PDSNs. This transport is configured using Interprocess Communication (IPC) commands.
To configure the inter-device communication transport between the two PDSNs, use the following commands beginning in global configuration mode:
Using the Loopback Interface For the PDSN-AAA Server Interface
To ensure that the AAA server views the active and standby units as a single NAS, the same NAS IP address should be used by both the units. Now, the NAS IP Address can be configured for the PDSN using the ip radius source-interface command. When configured, the IP address of that interface is used as the NAS IP Address.
However, the CLI does not support virtual IP addresses (HSRP). As a result, the only way to ensure that both the units appear as a single NAS is to configure a loopback interface, and use that interface as the source-interface. In short, the CLI would look something like:
ip radius source-interface Loopback1
Configuring Application Tracking to Handle active-active Situation
Configuring AAA in the PDSN Environment
Access control is the way you manage who is allowed access to the network server and the services they are allowed to use. AAA network security services provide the primary framework through which you set up access control on your router or access server. For detailed information about AAA configuration options, refer to the "Configuring Authentication," and "Configuring Accounting" chapters in the Cisco IOS Security Configuration Guide.
To configure AAA in the PDSN environment, use the following commands in global configuration mode:
Configuring RADIUS in the PDSN Environment
RADIUS is a method for defining the exchange of AAA information in the network. In the Cisco implementation, RADIUS clients run on Cisco routers and send authentication requests to a RADIUS server that contains all user authentication and network server access information. For detailed information about RADIUS configuration options, refer to the "Configuring RADIUS" chapter in the Cisco IOS Security Configuration Guide.
To configure RADIUS in the PDSN environment, use the following commands in global configuration mode:
Configuring Prepaid in the PDSN Environment
For the 1.2 release of the Cisco PDSN software, to configure prepaid, ensure that you include crb-entity-type=1 in the user profile.
In Cisco PDSN release 2.0 and above, to configure IS835C Prepaid, use the following commands in global configuration mode:
router (config)# cdma pdsn accounting prepaid ?
duration
threshold
volume
Prepaid service based on duration.
Configure threshold percentage per quota.
Prepaid service based on volume.
Enabling VPDN in a PDSN Environment
To configure VPDN in the PDSN environment, use the following commands in global configuration mode:
Router(config)# vpdn enable
Enables VPDN.
Router(config)# vpdn authen-before-forward
Specifies to authenticate a user locally before tunneling.
For more information about VPDNs, refer to the Cisco IOS Release 12.3 documentation modules Cisco IOS Dial Services Configuration Guide: Network Services and Cisco IOS Dial Services Command Reference.
Configuring the Mobile IP FA
Mobile IP operation (as specified by TR-45.6) requires the ability to authenticate a mobile station through a challenge/response mechanism between the PDSN (acting as an FA) and the mobile station.
To configure the Mobile IP FA, use the following commands in global and interface configuration modes:
To reduce the virtual-access cloning time in order to increase the CPS rate on a standalone PDSN on a Cisco router, use the following per interface configurations in global configuration mode:
The CPS on a standalone PDSN on a Cisco Router should improve to 100 CPS from the current number of 40.
Configuring Proxy Mobile IP Attributes Locally
As an alternative to true Mobile IP, which is not supported by all mobile devices, you can configure the Cisco PDSN to provide many of the benefits of Mobile IP through the use of proxy Mobile IP. All proxy Mobile IP attributes can be retrieved from the AAA server. To configure proxy Mobile IP attributes locally, use the following command in global configuration mode:
Configuring Mobile IP Security Associations
To configure security associations for mobile hosts, FAs, and HAs, use one of the following commands in global configuration mode:
Configuring PDSN Cluster Controller
To configure the PDSN Cluster Controller attributes locally, use the following commands in global configuration mode.
Note
Configuring PDSN Cluster Member
To configure the PDSN Cluster Member attributes locally, use the following commands in global configuration mode:
Note
Enabling Network Management
To enable SNMP network management for the PDSN, use the following commands in global configuration mode:
Configuring Always On Service
Always On service maintains the subscriber's packet data session in the local network. The PDSN will not initiate release of the subscriber's packet data session due to PPP idle timer expiry, unless the PDSN determines the user is no longer reachable. The Always On feature is enabled by default. To change the default parameters related to this feature, use following command:
Configuring A11 Session Updates
A11 Session Update messages are sent from the PDSN to the PCF to add, change, or update session parameters for an A10 connection. To enable the A11 Session Update feature, perform the following tasks:
Configuring SDB Indicator Marking
This feature supports short data burst applications, such as SIP signaling for PTT applications, and proposes the interaction with the PDSN. SIP is used by PTT applications to signal a PTT call. The message is short and needs to be delivered to the end-user. The Short Data Burst support on the RAN can be used to send these to the end-user, especially when the messages are to be terminated to the mobile. This is especially important when the mobile user is actually dormant. Use the following command to configure SDB Indicator Marking:
Configuring SDB Indicator Marking for PPP Control Packets
While data packets can be sent towards the mobile using SDBs as shown above, SDBs can also be used for delivering PPP control packets. This can be particularly helpful for Always-On sessions, where the session is dormant. Basically, with Always On configured, the PDSN sends out LCP echo requests (and waits for LCP echo replies) to keep the session alive. Hence, when such a session goes dormant, a data channel needs to be setup to deliver these LCP echo requests to the MN. The other option is to use SDBs to deliver the LCP echo requests without setting up a data channel.
Use the following CLI in conjunction of the above CLI to enable this feature:
Router(config)# cdma pdsn a11 dormant sdb-indication match-qos-group group-number ppp-ctrl-pkts
The group-number represents the classified match criteria.
Configuring PoD on the PDSN
To enable the Packet of Disconnect (RADIUS Disconnect) feature on the PDSN, perform the following tasks:
Configuring Mobile IP Resource Revocation on the PDSN
To enable resource revocation support on PDSN, perform the following task:
Configuring Closed-RP Interfaces
To enable the Closed-RP feature on the PDSN, perform the following tasks:
Here is a sample configuration for the Closed-RP feature on the PDSN:
Router#sh runBuilding configuration...Current configuration : 3450 bytes!! Last configuration change at 04:23:40 UTC Tue May 27 2003! NVRAM config last updated at 04:24:03 UTC Tue May 27 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname Router!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization ipmobile default group radiusaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookupip dhcp ping packets 0!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.3 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.173 255.255.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.3 255.0.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.43 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool mobilenodes 30.0.0.2 30.0.0.255ip local pool pdsn-pool 122.3.0.1 122.3.16.1ip local pool pdsn-pool 122.4.0.1 122.4.16.1ip local pool pdsn-pool 122.5.0.1 122.5.16.1ip local pool pdsn-pool 122.1.0.1 122.1.16.1ip local pool pdsn-pool 122.2.0.1 122.2.16.1ip default-gateway 9.15.0.1ip classlessip route 7.0.0.1 255.255.255.255 16.1.1.60ip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11no ip http server!!!!radius-server host 10.76.86.62 auth-port 1645 acct-port 1646 key ciscoradius-server key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all
Note
For information regarding VPDN configuration details, please refer to the following URL:
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps5207/products_command_reference_chapter09186a00801a7e8f.html#wp1167095
For information regarding Layer 2 Tunneling Protocol (L2TP) tunnel configuration details, please refer to the following URL:
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps5207/products_command_reference_chapter09186a00801a7e90.html
For information regarding IOS Server Load Balancing, please refer to the following URL:
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps5012/products_feature_guide09186a008020b9f3.html#wp3601032
Configuring Short Data Burst Flagging
This feature adds support for short data burst applications such as SIP signaling for PTT applications, and proposes the interaction with PDSN. SIP is used by PTT applications to signal a PTT call. The message is short and needs to be delivered to the end-user. The Short Data Burst support on the RAN can be used to send these over to the end-user, especially when the messages are to be terminated to the mobile.
To configure SDB on the PDSN so that all packets that are set with the specific group-number will be flagged for SDB usage between the PCF and the PDSN, use the following command in global configuration:
Configuring PDSN Accounting Events
To configure attributes of PDSN accounting events, use the following commands in global configuration mode:
Configuring CDMA RADIUS Attributes
To configure both authentication and accounting requests on the PDSN, perform the following tasks:
Monitoring and Maintaining the PDSN
To monitor and maintain the PDSN, use the following commands in privileged EXEC mode:
Configuration Examples
This section provides the following configuration examples:
•
•
•
•
•
•
Cisco PDSN Configuration for Simple IP
Figure 9 and the information that follows is an example of PDSN architecture for Simple IP and its accompanying configuration.
Figure 9 PDSN for Simple IP—A Network Map
service cdma pdsn!hostname PDSN1-7206!aaa new-modelaaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting update periodic 60aaa accounting network pdsn start-stop group radius!no ip gratuitous-arps!interface Loopback0ip address 8.8.8.254 255.255.255.255!interface CDMA-Ix1ip address 6.6.6.6 255.0.0.0!interface FastEthernet0/0! Interface for communication with RADIUS server and NMSip address 33.33.33.33 255.255.255.0!!!interface FastEthernet1/0! Interface to PCF - R-Pip address 2.2.2.2 255.255.255.0half-duplexno cdp enable!interface FastEthernet2/0! Interface to external network - Piip address 23.23.23.23 255.255.0.0!!!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolppp accm 0ppp authentication chap pap optionalppp accounting noneppp timeout idle 2000!ip local pool pdsn-pool 8.8.8.1 8.8.8.253ip classles!!radius-server host 33.33.33.34 auth-port 1645 acct-port 1646 key ciscoradius-server retransmit 3radius-server vsa send authentication 3gpp2radius-server vsa send accounting 3gpp2cdma pdsn virtual-template 1cdma pdsn maximum sessions 16000cdma pdsn a10 max-lifetime 36000cdma pdsn msid-authenticationcdma pdsn secure pcf 2.2.2.5 spi 100 key ascii cisco!!!endCisco PDSN Configuration for Simple IP with VPDN
The configuration Simple IP with VPDN is identical to the configuration for Simple IP with two additional lines:
vpdn enablevpdn authen-before-forwardCisco PDSN Configuration for Mobile IP
Figure 10 and the information that follows is an example of PDSN architecture for Mobile IP service and its accompanying configuration. The example shows the configuration of PDSN1.
Figure 10 PDSN for Mobile IP—A Network Map
service cdma pdsn!hostname PDSN1-7206!aaa new-modelaaa authentication login default group radiusaaa authentication login CONSOLE noneaaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radius!interface Loopback0ip address 11.11.11.1 255.255.255.255!interface CDMA-Ix1ip address 5.5.5.5 255.0.0.0!interface FastEthernet0/0description AAA NMS interfaceip address 12.12.12.100 255.0.0.0!interface FastEthernet1/0description R-P interfaceip address 2.2.2.2 255.255.255.0full-duplex!!interface FastEthernet2/0description Pi interfaceip address 3.3.3.2 255.255.255.0full-duplex!interface Virtual-Template1ip unnumbered loopback0no ip route-cacheno keepaliveppp authentication chap pap optionalppp timeout idle 2000!router mobile!ip classlessno ip http serverip mobile foreign-agent care-of FastEthernet2/0ip mobile foreign-service challenge forward-mfce timeout 10 window 10ip mobile foreign-service reverse-tunnelradius-server host 12.12.22.12 auth-port 1645 acct-port 1646 key ascii cisco!radius-server host 12.12.22.12 auth-port 1645 acct-port 1646 key ascii ciscoradius-server retransmit 3radius-server vsa send authentication 3gpp2radius-server vsa send accounting 3gpp2cdma pdsn secure pcf 2.2.2.1 spi 100 key ascii ciscocdma pdsn virtual-template 1cdma pdsn msid-authentication!!endCombined Configuration for Cisco PDSN
The following example illustrates a PDSN configured for all scenarios: Simple IP, Simple IP with VPDN, Mobile IP, and Proxy Mobile IP.
service cdma pdsn!hostname PDSN1!aaa new-modelaaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting update periodic 60aaa accounting network pdsn start-stop group radius!vpdn enablevpdn authen-before-forwardvirtual-profile aaausername HA password 0 rosebudusername LNS password 0 ciscousername PDSN password 0 ciscono ip gratuitous-arps!interface Loopback0ip address 8.8.8.254 255.255.255.255!interface CDMA-Ix1ip address 6.6.6.6 255.0.0.0!interface FastEthernet0/0! Interface for communication with RADIUS server and NMSip address 33.33.33.33 255.255.255.0!!!interface FastEthernet1/0! Interface to PCF - R-Pip address 2.2.2.2 255.255.255.0!interface FastEthernet2/0! Interface to external network - Piip address 23.23.23.23 255.255.0.0!!!interface Virtual-Template1ip unnumbered Loopback0no keepalivepeer default ip address pool pdsn-poolppp accm 0ppp authentication chap pap optionalppp accounting noneppp timeout idle 2000!router mobile!ip local pool pdsn-pool 8.8.8.1 8.8.8.253ip classlessip mobile foreign-agent care-of FastEthernet2/0ip mobile foreign-service challenge forward-mfce timeout 10 window 10ip mobile foreign-service reverse-tunnelradius-server host 12.12.22.12 auth-port 1645 acct-port 1646 key ascii cisco!!radius-server host 33.33.33.34 auth-port 1645 acct-port 1646 key ciscoradius-server retransmit 3radius-server vsa send authentication 3gpp2radius-server vsa send accounting 3gpp2cdma pdsn virtual-template 1cdma pdsn maximum sessions 16000cdma pdsn a10 max-lifetime 36000cdma pdsn msid-authenticationcdma pdsn secure pcf 2.2.2.5 spi 100 key ascii ciscocdma pdsn secure cluster default spi 100 key ascii cisco!!!endPDSN Cluster Configuration
The following configuration illustrates 3 MWAMs in a 6500 configuration:
Verify hardware configuration on Cat6K:cat6500 router#sh moduleMod Ports Card Type----------------------------------------------1 2 Catalyst 6000 supervisor 2 (Active)3 48 SFM-capable 48-port 10/100 Mbps RJ454 2 IPSec VPN Accelerator5 16 SFM-capable 16 port 1000mb GBIC7 3 MWAM Module8 3 MWAM Module (MP)9 3 MWAM ModuleMod MAC addresses Hw Fw Sw Status--- ---------------------------------- ------ ------------ ------------ -------1 0005.7485.8494 to 0005.7485.8495 3.5 6.1(3) 6.2(2.108) Ok3 0001.63d7.2352 to 0001.63d7.2381 4.2 6.3(1) 6.2(2.108) Ok4 0008.7ca8.1386 to 0008.7ca8.1389 0.200 7.2(1) 6.2(2.108) Ok5 0001.63d6.cd92 to 0001.63d6.cda1 4.1 6.3(1) 6.2(2.108) Ok7 0001.0002.0003 to 0001.0002.000a 0.203 7.2(1) 1.0(0.1) Ok8 00e0.b0ff.3a10 to 00e0.b0ff.3a17 0.201 7.2(1) 1.2(0.12) ShutDown9 0002.0002.0003 to 0002.0002.000a 0.203 7.2(1) 1.0(0.1) OkMod Sub-Module Hw Status--- --------------------------- ------- -------1 Policy Feature Card 2 3.2 Ok1 Cat6k MSFC 2 daughterboard 2.2 Okcat6500 router#Controller configuration:cat6500 router#session slot 7 processor 6The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.76 ... OpenPress RETURN to get started!S76>S76>S76>S76>enS76#sh runS76#sh running-configBuilding configuration...Current configuration : 1489 bytes!! No configuration change since last restart!version 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice cdma pdsn!hostname S76!!ip subnet-zeroip cef!!!interface Loopback1no ip address!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.401encapsulation dot1Q 401ip address 10.121.68.76 255.255.255.0standby 1 ip 10.121.68.98standby 1 priority 120standby 1 preemptstandby 1 name 6509-cluster!router mobile!ip classlessip route 10.10.72.1 255.255.255.255 10.121.68.72ip route 10.10.73.1 255.255.255.255 10.121.68.73ip route 10.10.74.1 255.255.255.255 10.121.68.74ip route 10.10.75.1 255.255.255.255 10.121.68.75ip route 10.10.92.1 255.255.255.255 10.121.68.92ip route 10.10.93.1 255.255.255.255 10.121.68.93ip route 10.10.94.1 255.255.255.255 10.121.68.94ip route 10.10.95.1 255.255.255.255 10.121.68.95ip route 128.0.0.0 255.255.255.0 GigabitEthernet0/1no ip http serverip pim bidir-enable!!!cdma pdsn secure pcf 10.121.68.62 10.121.68.66 spi 100 key ascii ciscocdma pdsn secure pcf 10.121.68.82 10.121.68.86 spi 100 key ascii ciscocdma pdsn secure cluster default spi 100 key ascii usercdma pdsn cluster controller interface GigabitEthernet0/0.401cdma pdsn cluster controller standby 6509-clustercdma pdsn cluster controller timeout 10cdma pdsn cluster controller window 3!line con 0line vty 0no loginline vty 1 4loginline vty 5 15login!endrouter#cat6500 router#session slot 9 processor 6The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.96 ... Openrouter>Press RETURN to get started!router 96#show running-configBuilding configuration...Current configuration : 1182 bytes!! No configuration change since last restart!version 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice cdma pdsn!hostname router96!!ip subnet-zeroip cef!!!!interface Loopback1no ip address!interface CDMA-Ix1no ip address!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.401encapsulation dot1Q 401ip address 10.121.68.96 255.255.255.0standby 1 ip 10.121.68.98standby 1 priority 120standby 1 preemptstandby 1 name 6509-cluster!router mobile!ip classlessip route 10.10.72.1 255.255.255.255 10.121.68.72ip route 128.0.0.0 255.255.255.0 GigabitEthernet0/2no ip http serverip pim bidir-enable!!!cdma pdsn secure pcf 10.121.68.62 10.121.68.66 spi 100 key ascii ciscocdma pdsn secure pcf 10.121.68.82 10.121.68.86 spi 100 key ascii ciscocdma pdsn secure cluster default spi 100 key ascii usercdma pdsn cluster controller interface GigabitEthernet0/0.401cdma pdsn cluster controller standby 6509-clustercdma pdsn cluster controller timeout 10cdma pdsn cluster controller window 3!line con 0line vty 0no loginline vty 1 4loginline vty 5 15login!endrouter96#Verify active controller and standby controllerrouter76#show standbyGigabitEthernet0/0.401 - Group 1State is Active2 state changes, last state change 00:27:09Virtual IP address is 10.121.68.98Active virtual MAC address is 0000.0c07.ac01Local virtual MAC address is 0000.0c07.ac01 (default)Hello time 3 sec, hold time 10 secNext hello sent in 2.112 secsPreemption enabled, min delay 0 sec, sync delay 0 secActive router is localStandby router is 10.121.68.96, priority 120 (expires in 9.064 sec)Priority 120 (configured 120)IP redundancy name is "6509-cluster"router76#router96#sh standbyGigabitEthernet0/0.401 - Group 1State is Standby1 state change, last state change 00:26:57Virtual IP address is 10.121.68.98Active virtual MAC address is 0000.0c07.ac01Local virtual MAC address is 0000.0c07.ac01 (default)Hello time 3 sec, hold time 10 secNext hello sent in 2.532 secsPreemption enabled, min delay 0 sec, sync delay 0 secActive router is 10.121.68.76, priority 120 (expires in 9.580 sec)Standby router is localPriority 120 (configured 120)IP redundancy name is "6509-cluster"router96#Members configuration:cat6500 router#session slot 7 processor 3The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.73 ... Openrouter73>Press RETURN to get started!router73#sh runrouter73#sh running-configBuilding configuration...Current configuration : 3192 bytes! Last configuration change at 04:10:06 UTC Sun Sep 15 2002!version 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice cdma pdsn!hostname router73!aaa new-model!!aaa group server radius CSCO-30server 10.1.1.244 auth-port 1645 acct-port 1646server 10.1.1.200 auth-port 2812 acct-port 2813!aaa authentication ppp default local group radiusaaa authorization network default local group radiusaaa accounting network pdsn start-stop group radiusaaa session-id common!username root nopasswordusername cisco password 0 ciscousername pdsn password 0 ciscoip subnet-zeroip gratuitous-arpsip cef!!!interface Loopback1ip address 10.10.173.1 255.255.255.0!interface CDMA-Ix1ip address 10.10.73.1 255.255.255.0tunnel source 10.10.73.1tunnel key 16404tunnel sequence-datagrams!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.310encapsulation dot1Q 310ip address 10.1.1.73 255.255.255.0!interface GigabitEthernet0/0.401encapsulation dot1Q 401ip address 10.121.68.73 255.255.255.0!interface Virtual-Template1ip unnumbered Loopback1no keepalivepeer default ip address pool pdsn-poolppp accm 0ppp authentication chap pap optionalppp ipcp address uniquecdma pdsn mobile-advertisement-burst interval 500 number 3!router mobile!router ospf 100log-adjacency-changessummary-address 7.3.0.0 255.255.0.0redistribute connected subnets route-map MAP-DENYnetwork 10.10.73.1 0.0.0.0 area 73network 10.10.73.0 0.0.0.255 area 73network 10.10.173.1 0.0.0.0 area 0network 10.121.68.0 0.0.0.255 area 0!ip local pool pdsn-pool 7.3.1.0 7.3.16.255ip local pool pdsn-pool 7.3.17.0 7.3.32.255ip local pool pdsn-pool 7.3.33.0 7.3.48.255ip local pool pdsn-pool 7.3.49.0 7.3.64.255ip local pool pdsn-pool 7.3.65.0 7.3.78.255ip local pool pdsn-pool 7.3.79.0 7.3.79.31ip mobile foreign-agent care-of GigabitEthernet0/0.310ip classlessip route 128.0.0.0 255.255.255.0 GigabitEthernet0/1no ip http serverip pim bidir-enableip mobile foreign-service challenge forward-mfceip mobile foreign-service reverse-tunnelcdma pdsn mobile-advertisement-burst interval 500 number 3!!access-list 9 deny 128.0.0.0 0.0.255.255access-list 9 permit any!route-map MAP-DENY permit 10match ip address 9set tag 9!radius-server host 10.1.1.244 auth-port 1645 acct-port 1646 key fooradius-server host 10.1.1.200 auth-port 2812 acct-port 2813 key fooradius-server retransmit 3radius-server deadtime 1radius-server vsa send accounting 3gpp2radius-server vsa send authentication 3gpp2cdma pdsn accounting local-timezonecdma pdsn virtual-template 1cdma pdsn send-agent-advcdma pdsn secure pcf 10.121.68.62 10.121.68.66 spi 100 key ascii ciscocdma pdsn secure pcf 10.121.68.82 10.121.68.86 spi 100 key ascii ciscocdma pdsn secure cluster default spi 100 key ascii usercdma pdsn cluster member controller 10.121.68.98cdma pdsn cluster member interface GigabitEthernet0/0.401cdma pdsn cluster member timeout 10cdma pdsn cluster member window 2!line con 0line vty 5 15!endShow commands on ControllersPDSN-CONTROLLER#show cdma pdsn cluster controller configurationcluster interface GigabitEthernet0/0.1no R-P signaling proxytimeout to seek member = 10 secondswindow to seek member is 2 timeouts in a row if no reply (afterwards the member is declared offline)default: spi 100, Timestamp +/- 0, key ascii clusteringthis PDSN cluster controller is configuredcontroller redundancy:database in-sync or no need to syncgroup: clusterController maximum number of load units = 1000PDSN-CONTROLLER#show cdma pdsn cluster controller member loadSecs until Seq seeks Member(past) seek no reply IPv4 Addr State Load Sessions-------------------------------------------------------------------6 0 20.6.84.1 ready 0 05 0 20.6.62.1 ready 0 01 0 20.6.64.1 ready 0 0-------------------------------------------------------------------Controller IPv4 Addr 20.3.68.60PDSN-CONTROLLER#show cdma pdsn cluster controller member 20.6.84.1PDSN cluster member 20.6.84.1 state readyregistered with PDSN controller 20.3.68.60reported load 0 percent, will be sought in 7 secondsMember 20.6.84.1 statistics:Controller seek rcvd 1, Member seek reply rcvd 554Member state changed 0 time to readyMember state changed 0 time to Admin prohibitedSession-Up message rcvd 0, Session-Down message received 0Member seek not replied in sequence 0PDSN-CONTROLLER#show cdma pdsn cluster controller statisticsController-Member Interface:Cluster Reg Request rcvd 858, accepted 852, discarded 6Cluster Reg Request sent 1425Cluster Reg Reply rcvd 1427, accepted 1424, discarded 3Cluster Reg message errors:Reg Request rcvd: Authentication failed 0, ID mismatch 6Unrecognized extension 0, Unrecognized application type 0Unrecognized data type 0Reg Reply rcvd: Authentication failed 0, ID mismatch 3Unrecognized extension 0Reg Req not sent: Interface cdma-Ix not configured 0Invalid Reg message type 0Controller seek requests rcvd 852, replies sent 852Member seek requests sent 1425, replies rcvd 1424Member state transition msgs rcvd 0, replies sent 0ready 0, Administratively prohibited 0Total A11 Reg Requests forwarded 0A11 Reg Requests orig forwarded 0, retry forwarded 0Session-Up from member 0, Session-Down from member 0No Acknowledgement from member 0Controller Redundancy Interface:Update rcvd 0 sent 2330 orig sent 2276 fail 18UpdateAck rcvd 2330 sent 0DownloadReq rcvd 0 sent 20 orig sent 19 fail 0DownloadReply rcvd 20 sent 0 orig sent 0 fail 0 drop 0DownloadAck rcvd 0 sent 20 drop 0Errors: Authentication failed 0 ID mismatch 0Ignored due to no redundancy configuration 0router76#sh cdma pdsn cluster controller session ?count Count of session recordsimsi Session record for International Mobile Subscriber Identityoldest Oldest session recordrouter76#sh cdma pdsn cluster controller session olrouter76#sh cdma pdsn cluster controller session oldest ?more The oldest and a few more session records to show| Output modifiers<cr>router76#sh cdma pdsn cluster controller session oldestIMSI Member IPv4 Addr Age [days] Anchor changes----------------------------------------------------------------62000015434 10.10.73.1----------------------------------------------------------------router76#sh cdma pdsn cluster controller session imsi 62000015434IMSI Member IPv4 Addr Age [days] Anchor changes----------------------------------------------------------------62000015434 10.10.73.1----------------------------------------------------------------router76#Show commands on member:PDSN-MEMBER#show cdma pdsn cluster member configurationcluster interface GigabitEthernet0/0.1IP address of controller is 20.3.68.60no prohibit administrativelytimeout to resend status or seek controller = 250 sec or less, randomizedresend a msg for 6 timeouts sequentially if no reply, then inform operatordefault: spi 100, Timestamp +/- 0, key ascii clusteringthis PDSN cluster member is configuredPDSN-MEMBER#show cdma pdsn cluster member statisticsController-Member Interface:Cluster Reg Request rcvd 593, accepted 593, discarded 0Cluster Reg Request sent 3Cluster Reg Reply rcvd 1, accepted 1, discarded 0Cluster Reg message errors:Reg Request rcvd: Authentication failed 0, ID mismatch 0Unrecognized extension 0, Unrecognized application type 0Unrecognized data type 0Reg Reply rcvd: Authentication failed 0, ID mismatch 0Unrecognized extension 0Reg Req not sent: Interface cdma-Ix not configured 0Invalid Reg message type 0Controller seek requests rcvd 593, replies sent 593Member seek requests sent 3, replies rcvd 1Member state transition msgs sent 0, replies rcvd 0ready 0, Administratively prohibited 0Session-Up msg sent 0, Session-Down msg sent 0Session-Up msg Ack rcvd 0, Session-Down msg Ack rcvd 0Controller seek not replied in sequence 0Member state not replied in sequence 0Cat6k SUP configurationcat6500 router#sh running-configBuilding configuration...Current configuration : 9838 bytes!! Last configuration change at 00:21:56 UTC Sat Sep 14 2002 by root! NVRAM config last updated at 14:10:00 UTC Fri Sep 13 2002 by root!version 12.2service timestamps debug uptimeservice timestamps log datetime localtimeno service password-encryption!hostname cat6500 router!boot system slot0:c6sp222-jk9sv-mzboot device module 4 cf:3boot device module 5 cf:4boot device module 6 cf:4boot device module 7 cf:4boot device module 8 cf:4boot device module 9 cf:4aaa new-modelaaa authentication login default localaaa authorization exec default localenable secret level 1 5 $1$T17C$7icHsiM4vHj6nIE6medGj.enable secret level 6 5 $1$wB/9$.ML91zZopFpYp12VNxA1p.enable password lab!username u0 privilege 0 password 0 ciscousername root nopasswordusername u1 password 0 ciscousername u6 privilege 6 password 0 ciscousername u8 privilege 8 password 0 ciscousername cisco password 0 ciscousername u2 privilege 2 nopasswordusername u15 privilege 15 nopasswordusername u10 privilege 10 nopasswordusername v1 nopassword user-maxlinks 1!monitor session 1 source interface Fa3/24monitor session 1 destination interface Fa3/12redundancymain-cpuauto-sync standardip subnet-zero!!no ip domain-lookup!mls flow ip destinationmls flow ipx destination!!no spanning-tree vlan 310!!!interface Loopback1ip address 10.10.10.10 255.255.255.0!interface Port-channel1no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface GigabitEthernet1/1no ip addresssnmp trap link-statusswitchportswitchport access vlan 309switchport mode access!interface GigabitEthernet1/2no ip addresssnmp trap link-statusswitchportswitchport access vlan 401switchport mode access!interface GigabitEthernet2/1no ip addresssnmp trap link-statusswitchportswitchport access vlan 310switchport mode access!interface GigabitEthernet2/2no ip addressshutdown!interface FastEthernet3/1no ip addresssnmp trap link-statusswitchportswitchport access vlan 222!interface FastEthernet3/2no ip addressshutdown!interface FastEthernet3/3no ip addressshutdown!interface FastEthernet3/4no ip addressshutdown!interface FastEthernet3/5no ip addresssnmp trap link-statusswitchportswitchport access vlan 66switchport mode access!interface FastEthernet3/6no ip addresssnmp trap link-statusswitchportswitchport access vlan 66switchport mode access!interface FastEthernet3/7no ip addresssnmp trap link-statusswitchportswitchport access vlan 66switchport mode access!interface FastEthernet3/8ip address 1.1.1.1 255.255.255.0shutdown!interface FastEthernet3/9no ip addressshutdown!interface FastEthernet3/10no ip addresssnmp trap link-statusswitchportswitchport access vlan 401channel-group 1 mode on!interface FastEthernet3/11no ip addresssnmp trap link-statusswitchportswitchport access vlan 401channel-group 1 mode on!interface FastEthernet3/12no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/13no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/14no ip addressshutdown!interface FastEthernet3/15ip address 3.3.3.3 255.255.255.0shutdown!interface FastEthernet3/16no ip addressshutdown!interface FastEthernet3/17no ip addresssnmp trap link-statusswitchportswitchport access vlan 311switchport mode access!interface FastEthernet3/18no ip addressshutdown!interface FastEthernet3/19no ip addressshutdown!interface FastEthernet3/20no ip addressshutdown!interface FastEthernet3/21no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/22no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/23no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/24no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/25no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/26no ip addresssnmp trap link-statusswitchportswitchport access vlan 401!interface FastEthernet3/27no ip addressshutdown!interface FastEthernet3/28no ip addressshutdown!interface FastEthernet3/29no ip addressshutdown!interface FastEthernet3/30no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/31no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/32no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/33no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/34no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/35no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/36no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/37no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/38no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/39no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/40no ip addressshutdownsnmp trap link-statusswitchportswitchport access vlan 333!interface FastEthernet3/41no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/42no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/43no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/44no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/45no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/46no ip addresssnmp trap link-statusswitchportswitchport access vlan 310!interface FastEthernet3/47no ip addresssnmp trap link-statusswitchportswitchport access vlan 333!interface FastEthernet3/48no ip addresssnmp trap link-statusswitchportswitchport access vlan 333!interface GigabitEthernet4/1no ip addresssnmp trap link-statusswitchportswitchport trunk encapsulation dot1qswitchport trunk allowed vlan 1,1002-1005switchport mode trunkflowcontrol receive oncdp enable!interface GigabitEthernet4/2no ip addresssnmp trap link-statusswitchportswitchport trunk encapsulation dot1qswitchport trunk allowed vlan 1,1002-1005switchport mode trunkflowcontrol receive oncdp enable!interface GigabitEthernet5/1no ip addressshutdown!interface GigabitEthernet5/2no ip addressshutdown!interface GigabitEthernet5/3no ip addressshutdown!interface GigabitEthernet5/4no ip addressshutdown!interface GigabitEthernet5/5no ip addressshutdown!interface GigabitEthernet5/6no ip addressshutdown!interface GigabitEthernet5/7no ip addressshutdown!interface GigabitEthernet5/8no ip addressshutdown!interface GigabitEthernet5/9no ip addressshutdown!interface GigabitEthernet5/10no ip addressshutdown!interface GigabitEthernet5/11no ip addressshutdown!interface GigabitEthernet5/12no ip addressshutdown!interface GigabitEthernet5/13no ip addressshutdown!interface GigabitEthernet5/14no ip addressshutdown!interface GigabitEthernet5/15no ip addressshutdown!interface GigabitEthernet5/16no ip addressshutdown!interface Vlan1no ip addressshutdown!interface Vlan222ip address 172.19.23.16 255.255.254.0ip nat outside!interface Vlan309no ip address!interface Vlan310ip address 10.1.1.222 255.255.255.0ip nat inside!interface Vlan401ip address 10.121.68.200 255.255.255.0!router ospf 100log-adjacency-changesnetwork 10.10.10.10 0.0.0.0 area 0network 10.121.68.0 0.0.0.255 area 0default-information originate!ip nat inside source list 100 interface Vlan222 overloadip classlessip route 0.0.0.0 0.0.0.0 172.19.26.1ip route 0.0.0.0 0.0.0.0 172.19.22.1ip route 5.5.5.0 255.255.255.0 10.1.1.92ip route 10.10.113.1 255.255.255.255 10.1.1.221ip route 10.10.116.1 255.255.255.255 10.1.1.221ip route 10.10.195.1 255.255.255.255 10.1.1.95no ip http serverip pim bidir-enable!!ip access-list extended VRZ-101permit ip host 10.10.195.1 host 10.10.116.1access-list 100 permit ip 5.0.0.0 0.255.255.255 anyarp 127.0.0.22 0000.2200.0000 ARPAarp 127.0.0.12 0000.2100.0000 ARPA!route-map MAP deny 10match ip address 100!snmp-server community public ROsnmp-server community private RWsnmp-server enable traps casasnmp-server enable traps vtpsnmp-server enable traps hsrpsnmp-server enable traps configsnmp-server enable traps entitysnmp-server enable traps bgpsnmp-server enable traps rsvpsnmp-server enable traps frame-relaysnmp-server enable traps syslogsnmp-server enable traps rtrsnmp-server enable traps dlswsnmp-server enable traps isdn call-informationsnmp-server enable traps isdn layer2snmp-server host 10.1.1.199 public!privilege configure level 8 snmp-server communityprivilege configure level 8 usernameprivilege configure level 8 username u10 privilege 10 nopasswordprivilege exec level 6 show runningprivilege exec level 8 config terminal!line con 0exec-timeout 0 0line vty 0 4exec-timeout 0 0password labtransport input lat pad mop telnet rlogin udptn nasiline vty 5 10exec-timeout 0 0!ntp master 3endClosed RP IOS SLB Load Balancing Configuration
The following configuration example illustrates the IOS Server Load Balancing for the Closed-RP feature on the PDSN. This example includes 6 instances of the PDSN.
Supervisor Configuration
SLB-6500#show running-configBuilding configuration...Current configuration : 6422 bytes!! Last configuration change at 00:37:57 UTC Thu Jun 5 2003! NVRAM config last updated at 02:54:07 UTC Wed May 28 2003!version 12.2service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname SLB-6500!logging snmp-authfail!clock calendar-validmwam module 5 port 1 allowed-vlan 1-1000mwam module 5 port 2 allowed-vlan 1-1000mwam module 5 port 3 allowed-vlan 1-1000mwam module 7 port 1 allowed-vlan 1-1000mwam module 7 port 2 allowed-vlan 1-1000mwam module 7 port 3 allowed-vlan 1-1000vtp mode transparentip subnet-zero!!no ip domain-lookup!!ip slb serverfarm PDSN-FARMreal 37.0.0.2weight 1inservice!real 37.0.0.3weight 1inservice!real 37.0.0.4weight 1inservice!real 37.0.0.5weight 1inservice!real 37.0.0.6weight 1inservice!ip slb vserver PDSN-SLBvirtual 150.150.0.100 udp 1701serverfarm PDSN-FARMsticky 65535 group 1 netmask 255.255.254.0idle 10inservice!mpls ldp logging neighbor-changesmls flow ip destinationmls flow ipx destinationmls verify ip length minimummls verify ipx length minimum!!!!!!spanning-tree mode pvstno spanning-tree vlan 24diagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!redundancymode rpr-plusmain-cpuauto-sync running-configauto-sync standard!vlan internal allocation policy ascending!vlan 4-5,7-9,11,16,20,24-25,36-37,47,99-100,199-200,300!!interface GigabitEthernet2/1no ip addressswitchportswitchport access vlan 4switchport mode access!interface GigabitEthernet2/2no ip addressswitchportswitchport access vlan 7!interface FastEthernet3/1ip address 10.76.86.60 255.255.255.192!interface FastEthernet3/2no ip addressshutdown!interface FastEthernet3/3no ip addressshutdown!interface FastEthernet3/4no ip addressswitchportswitchport access vlan 4!interface FastEthernet3/5no ip addressspeed 100duplex fullswitchportswitchport access vlan 4!interface FastEthernet3/6no ip addressswitchportswitchport access vlan 4!interface FastEthernet3/7no ip addressswitchportswitchport access vlan 8!interface FastEthernet3/8no ip addressswitchportswitchport access vlan 8!interface FastEthernet3/9no ip addressswitchportswitchport access vlan 9!interface FastEthernet3/10no ip addressshutdown!interface FastEthernet3/11no ip addressswitchportswitchport access vlan 100!interface FastEthernet3/12no ip addressswitchportswitchport access vlan 47!interface FastEthernet3/13no ip addressspeed 100duplex halfswitchportswitchport access vlan 100!interface FastEthernet3/14no ip addressswitchportswitchport access vlan 100!interface FastEthernet3/15no ip addressshutdown!interface FastEthernet3/16no ip addressswitchportswitchport access vlan 4!interface FastEthernet3/17no ip addressshutdown!interface FastEthernet3/18no ip addressshutdown!interface FastEthernet3/19no ip addressswitchportswitchport access vlan 199!interface FastEthernet3/20no ip addressswitchportswitchport access vlan 20!interface FastEthernet3/21no ip addressshutdown!interface FastEthernet3/22no ip addressshutdown!interface FastEthernet3/23no ip addressshutdown!interface FastEthernet3/24no ip addressduplex halfswitchportswitchport access vlan 7!interface FastEthernet3/25no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/26no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/27no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/28no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/29no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/30no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/31no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/32no ip addressshutdown!interface FastEthernet3/33no ip addressshutdown!interface FastEthernet3/34no ip addressshutdown!interface FastEthernet3/35no ip addressswitchportswitchport access vlan 25!interface FastEthernet3/36no ip addressswitchportswitchport access vlan 36!interface FastEthernet3/37no ip addressshutdown!interface FastEthernet3/38no ip addressshutdown!interface FastEthernet3/39no ip addressshutdown!interface FastEthernet3/40no ip addressshutdown!interface FastEthernet3/41no ip address!interface FastEthernet3/42no ip addressswitchportswitchport access vlan 200!interface FastEthernet3/43no ip addressswitchportswitchport access vlan 16!interface FastEthernet3/44no ip addressswitchportswitchport access vlan 16!interface FastEthernet3/45no ip addressshutdown!interface FastEthernet3/46no ip addressshutdown!interface FastEthernet3/47no ip addressshutdown!interface FastEthernet3/48no ip addressshutdown!interface Vlan1no ip address!interface Vlan4ip address 150.150.0.2 255.255.254.0!interface Vlan5no ip address!interface Vlan7ip address 7.0.0.111 255.0.0.0!interface Vlan9no ip address!interface Vlan16ip address 16.1.1.1 255.0.0.0!interface Vlan20ip address 15.1.1.50 255.0.0.0!interface Vlan25ip address 9.15.50.4 255.255.0.0!interface Vlan36ip address 36.0.0.20 255.0.0.0!interface Vlan37ip address 37.0.0.1 255.0.0.0!interface Vlan47ip address 47.0.0.111 255.0.0.0!interface Vlan99ip address 99.99.11.1 255.0.0.0!interface Vlan100ip address 20.1.1.50 255.0.0.0!ip default-gateway 9.15.0.1ip classlessip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 64.0.0.0 255.0.0.0 10.76.86.1no ip http server!!!!!dial-peer cor custom!!!alias exec cls clear ip slb sessionsalias exec clr clear countersalias exec cpu show proc cpu | inc CPUalias exec hist show proc cpu historyalias exec clss clear ip slb sessionsalias exec clsc clear ip slb countersalias exec clc clear counters!line con 0exec-timeout 0 0line vty 0 4exec-timeout 0 0privilege level 15no loginline vty 5 15exec-timeout 0 0privilege level 15no login!!monitor session 1 source interface Fa3/6ntp clock-period 17179954ntp masterntp server 9.15.50.4endSLB-6500#PDSN Configuration
MWAM-PDSN2#sh runBuilding configuration...Current configuration : 3872 bytes!! Last configuration change at 00:34:06 UTC Thu Jun 5 2003! NVRAM config last updated at 00:35:49 UTC Thu Jun 5 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname MWAM-PDSN2!boot-start-markerboot-end-marker!no logging buffered!username MWAM-PDSN2 password 0 ciscousername HA password 0 ciscoaaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookupip dhcp ping packets 0!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.1 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1tunnel sequence-datagramstunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.172 255.255.0.0!interface GigabitEthernet0/0.7encapsulation dot1Q 7ip address 7.0.0.1 255.0.0.0!interface GigabitEthernet0/0.8encapsulation dot1Q 8ip address 8.0.0.11 255.0.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.2 255.0.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.42 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool pdsn-test 13.2.0.1 13.2.0.100ip local pool pdsn-pool 121.1.0.1 121.1.16.1ip local pool pdsn-pool 121.2.0.1 121.2.16.1ip local pool pdsn-pool 121.3.0.1 121.3.16.1ip local pool pdsn-pool 121.4.0.1 121.4.16.1ip local pool pdsn-pool 121.5.0.1 121.5.16.1ip default-gateway 9.15.0.1ip classlessip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.8 255.255.255.255 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.32ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.33ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11ip mobile foreign-agent care-of GigabitEthernet0/0.7no ip http server!!!!radius-server host 10.76.86.62 auth-port 1645 acct-port 1646 key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!alias exec cls clear cdma pdsn session allalias exec cpu show proc cpu | i CPUalias exec crad clear radius statisticsalias exec tclear clear vpdn tunnel l2tp allalias exec cstats clear cdma pdsn statisticsalias exec sip show cdma pdsn | i Simplealias exec hist sh proc cpu hist!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all!!endMWAM-PDSN2#MWAM-PDSN3#sh runBuilding configuration...Current configuration : 3479 bytes!! Last configuration change at 00:34:36 UTC Thu Jun 5 2003! NVRAM config last updated at 00:34:38 UTC Thu Jun 5 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname MWAM-PDSN3!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization ipmobile default group radiusaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookupip dhcp ping packets 0!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.3 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.173 255.255.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.3 255.0.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.43 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool mobilenodes 30.0.0.2 30.0.0.255ip local pool pdsn-pool 122.3.0.1 122.3.16.1ip local pool pdsn-pool 122.4.0.1 122.4.16.1ip local pool pdsn-pool 122.5.0.1 122.5.16.1ip local pool pdsn-pool 122.1.0.1 122.1.16.1ip local pool pdsn-pool 122.2.0.1 122.2.16.1ip default-gateway 9.15.0.1ip classlessip route 7.0.0.1 255.255.255.255 16.1.1.60ip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11no ip http server!!!!radius-server host 10.76.86.62 auth-port 1645 acct-port 1646 key ciscoradius-server key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!alias exec cls clear cdma pdsn session allalias exec cpu show proc cpu | i CPUalias exec crad clear radius statisticsalias exec tclear clear vpdn tunnel l2tp allalias exec cstats clear cdma pdsn statisticsalias exec sip show cdma pdsn | i Simple!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all!!endMWAM-PDSN3#MWAM-PDSN4#sh running-configBuilding configuration...Current configuration : 3387 bytes!! Last configuration change at 00:34:26 UTC Thu Jun 5 2003! NVRAM config last updated at 00:34:28 UTC Thu Jun 5 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname MWAM-PDSN4!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookup!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.2 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.174 255.255.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.4 255.0.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.44 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!ip local pool pdsn-pool 123.1.0.1 123.1.16.1ip local pool pdsn-pool 123.2.0.1 123.2.16.1ip local pool pdsn-pool 123.3.0.1 123.3.16.1ip local pool pdsn-pool 123.4.0.1 123.4.16.1ip local pool pdsn-pool 123.5.0.1 123.5.16.1ip classlessip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.8 255.255.255.255 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.32ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.33ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11no ip http server!!!!radius-server host 9.15.50.5 auth-port 1645 acct-port 1646 key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!alias exec cls clear cdma pdsn session allalias exec cpu show proc cpu | i CPUalias exec crad clear radius statisticsalias exec tclear clear vpdn tunnel l2tp allalias exec cstats clear cdma pdsn statisticsalias exec sip show cdma pdsn | i Simple!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all!!endMWAM-PDSN4#MWAM-PDSN5#sh running-configBuilding configuration...Current configuration : 3389 bytes!! Last configuration change at 00:34:48 UTC Thu Jun 5 2003! NVRAM config last updated at 00:34:50 UTC Thu Jun 5 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname MWAM-PDSN5!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookup!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.5 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.175 255.255.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.5 255.255.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.45 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!ip local pool pdsn-pool 124.1.0.1 124.1.16.1ip local pool pdsn-pool 124.2.0.1 124.2.16.1ip local pool pdsn-pool 124.3.0.1 124.3.16.1ip local pool pdsn-pool 124.4.0.1 124.4.16.1ip local pool pdsn-pool 124.5.0.1 124.5.16.1ip classlessip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.8 255.255.255.255 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.32ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.33ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11no ip http server!!!!radius-server host 9.15.50.5 auth-port 1645 acct-port 1646 key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!alias exec cls clear cdma pdsn session allalias exec cpu show proc cpu | i CPUalias exec crad clear radius statisticsalias exec tclear clear vpdn tunnel l2tp allalias exec cstats clear cdma pdsn statisticsalias exec sip show cdma pdsn | i Simple!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all!!endMWAM-PDSN5#MWAM-PDSN6#sh running-configBuilding configuration...Current configuration : 3387 bytes!! Last configuration change at 00:35:03 UTC Thu Jun 5 2003! NVRAM config last updated at 00:35:44 UTC Thu Jun 5 2003!version 12.3service timestamps debug datetime msec localtimeservice timestamps log datetime msec localtimeno service password-encryptionservice cdma pdsn!hostname MWAM-PDSN6!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa accounting network pdsn start-stop group radius!aaa session-id commonip subnet-zerono ip gratuitous-arpsip cefno ip domain lookup!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group CDMA! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 150.150.0.100l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 87.0.0.6 255.0.0.0!interface CDMA-Ix1ip address 150.150.0.100 255.255.254.0tunnel source 150.150.0.100tunnel key 1tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.2encapsulation dot1Q 25ip address 9.15.50.176 255.255.0.0!interface GigabitEthernet0/0.37encapsulation dot1Q 37ip address 37.0.0.6 255.0.0.0!interface GigabitEthernet0/0.47encapsulation dot1Q 47ip address 47.0.0.46 255.0.0.0!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!ip local pool pdsn-pool 125.1.0.1 125.1.16.1ip local pool pdsn-pool 125.2.0.1 125.2.16.1ip local pool pdsn-pool 125.3.0.1 125.3.16.1ip local pool pdsn-pool 125.4.0.1 125.4.16.1ip local pool pdsn-pool 125.5.0.1 125.5.16.1ip classlessip route 9.100.0.0 255.255.0.0 9.15.0.1ip route 10.76.86.8 255.255.255.255 9.15.0.1ip route 10.76.86.41 255.255.255.255 9.15.0.1ip route 10.76.86.62 255.255.255.255 9.15.0.1ip route 150.150.2.2 255.255.255.255 47.0.0.2ip route 150.150.2.3 255.255.255.255 47.0.0.3ip route 150.150.4.2 255.255.255.255 47.0.0.4ip route 150.150.4.3 255.255.255.255 47.0.0.5ip route 150.150.6.2 255.255.255.255 47.0.0.32ip route 150.150.6.2 255.255.255.255 47.0.0.6ip route 150.150.6.3 255.255.255.255 47.0.0.33ip route 150.150.6.3 255.255.255.255 47.0.0.7ip route 150.150.8.2 255.255.255.255 47.0.0.8ip route 150.150.8.3 255.255.255.255 47.0.0.9ip route 150.150.10.2 255.255.255.255 47.0.0.10ip route 150.150.10.3 255.255.255.255 47.0.0.11no ip http server!!!!radius-server host 9.15.50.5 auth-port 1645 acct-port 1646 key ciscoradius-server vsa send accounting 3gpp2cdma pdsn pcf default closed-rpcdma pdsn virtual-template 1no cdma pdsn a10 ahdlc trailer!control-plane!alias exec cls clear cdma pdsn session allalias exec cpu show proc cpu | i CPUalias exec crad clear radius statisticsalias exec tclear clear vpdn tunnel l2tp allalias exec cstats clear cdma pdsn statisticsalias exec sip show cdma pdsn | i Simple!line con 0exec-timeout 0 0transport preferred alltransport output allline vty 0 4exec-timeout 0 0transport preferred alltransport input alltransport output allline vty 5 15exec-timeout 0 0transport preferred alltransport input alltransport output all!!endMWAM-PDSN6#Open-Closed RP Configuration Example
Controller Configuration
version 12.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryptionservice internalservice cdma pdsn!hostname ctlr76!boot-start-markerboot-end-marker!no logging buffered!no aaa new-model!resource policy!clock timezone IST 5 30ip subnet-zerono ip gratuitous-arps!!ip cefno ip domain lookupno ip dhcp use vrf connectedip dhcp ping packets 0!!vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group 1! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 41.0.0.41l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!vpdn-group MEMBERSrequest-dialinprotocol l2tpsource-ip 41.0.0.41l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0no ip address!interface CDMA-Ix1no ip addresstunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.110description PCFencapsulation dot1Q 110ip address 41.0.0.76 255.0.0.0no snmp trap link-statusno cdp enablestandby 1 ip 41.0.0.41standby 1 priority 110standby 1 preemptstandby 1 name SSP-CTLR!ip classlessip route 5.0.0.82 255.255.255.255 41.0.0.82no ip http server!!!!!no cdma pdsn a10 gre sequencingcdma pdsn timeout a11-update 5cdma pdsn secure pcf default spi 100 key ascii ciscocdma pdsn secure cluster default spi 100 key ascii ciscocdma pdsn cluster controller interface GigabitEthernet0/0.110cdma pdsn cluster controller standby SSP-CTLRcdma pdsn cluster controller member periodic-updatecdma pdsn cluster controller queueingcdma pdsn cluster controller closed-rp MEMBERS!control-plane!line con 0exec-timeout 0 0line vty 0exec-timeout 0 0line vty 1 4line vty 5 15!!endMember Configuration
! Last configuration change at 10:46:54 IST Fri Nov 11 2005! NVRAM config last updated at 14:17:44 IST Thu Nov 10 2005!version 12.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryptionservice internalservice cdma pdsn!hostname mem82a!boot-start-markerboot-end-marker!!redundancy inter-devicescheme standby PDSN-SSP-SR!!redundancyenable password lab!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization ipmobile default group radiusaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting network pdsn start-stop group radius!!aaa session-id common!resource policy!!ipc zone defaultassociation 1no shutdownprotocol sctplocal-port 2000local-ip 41.0.1.82remote-port 2000remote-ip 41.0.2.82!clock timezone IST 5 30ip subnet-zerono ip gratuitous-arps!!ip cefno ip domain lookupno ip dhcp use vrf connected!!subscriber redundancy rate 500 1vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group 1! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 5.0.0.82l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!interface Loopback0ip address 82.82.82.82 255.255.255.0!interface Loopback1ip address 7.0.0.82 255.255.255.0!interface CDMA-Ix1ip address 5.0.0.82 255.255.255.0tunnel source 5.0.0.82tunnel key 107036tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.51description AAAencapsulation dot1Q 51ip address 51.0.0.82 255.0.0.0no snmp trap link-status!interface GigabitEthernet0/0.71description PIencapsulation dot1Q 71ip address 71.0.1.82 255.0.0.0no snmp trap link-statusstandby 182 ip 71.0.0.82standby 182 follow PDSN-SSP-SR!interface GigabitEthernet0/0.110description RPencapsulation dot1Q 110ip address 41.0.1.82 255.0.0.0no snmp trap link-statusstandby 82 ip 41.0.0.82standby 82 name PDSN-SSP-SR!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool ispabc-pool1no keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool ispabc-pool1 82.0.1.0 82.0.16.255ip local pool ispabc-pool1 82.0.17.0 82.0.32.255ip local pool ispabc-pool1 82.0.33.0 82.0.48.255ip local pool ispabc-pool1 82.0.49.0 82.0.64.255ip local pool ispabc-pool1 82.0.65.0 82.0.79.31ip classlessip route 72.0.0.0 255.0.0.0 71.0.0.254no ip http serverip mobile foreign-agent care-of Loopback1ip mobile foreign-service challengeip mobile foreign-service reverse-tunnelip mobile registration-lifetime 65535!!!snmp-server community public RO!!radius-server host 51.0.0.2 auth-port 1645 acct-port 1646 key ciscocdma pdsn pcf default closed-rpcdma pdsn accounting send start-stopcdma pdsn virtual-template 1cdma pdsn a10 max-lifetime 65535no cdma pdsn a10 gre sequencingcdma pdsn timeout a11-update 5cdma pdsn secure pcf default spi 100 key ascii cisco replay 200cdma pdsn secure cluster default spi 100 key ascii ciscocdma pdsn cluster member controller 41.0.0.41cdma pdsn cluster member interface GigabitEthernet0/0.110cdma pdsn cluster member queueingcdma pdsn redundancy!control-plane!line con 0exec-timeout 0 0line vty 0exec-timeout 0 0line vty 1 4line vty 5 15!!endSession Redundancy Configuration Examples
Supervisor Configuration
!! Last configuration change at 14:50:14 IST Tue Dec 13 2005! NVRAM config last updated at 17:20:23 IST Wed Nov 30 2005!upgrade fpd autoversion 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice counters max age 10!hostname mwtbc11-7609a!boot system flash disk0:logging snmp-authfailenable password lab!no aaa new-modelclock timezone IST 5 30mwam module 7 port 1 allowed-vlan 1-4094mwam module 7 port 2 allowed-vlan 1-4094mwam module 7 port 3 allowed-vlan 1-4094mwam module 8 port 1 allowed-vlan 1-4094mwam module 8 port 2 allowed-vlan 1-4094mwam module 8 port 3 allowed-vlan 1-4094ip subnet-zeroip rcmd rcp-enable!!no ip domain-lookup!ipv6 mfib hardware-switching replication-mode ingressmls ip multicast flow-stat-timer 9no mls flow ipno mls flow ipv6no mls acl tcam share-globalmls cef error action freezeno scripting tcl initno scripting tcl encdir!!redundancymode rpr-plusmain-cpuauto-sync running-configauto-sync standardspanning-tree mode pvstno spanning-tree optimize bpdu transmissionspanning-tree extend system-iddiagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!vlan internal allocation policy ascendingvlan access-log ratelimit 2000!!interface FastEthernet1/1no ip addressshutdown!interface FastEthernet1/2no ip addressshutdown!interface FastEthernet1/3switchportswitchport access vlan 71switchport mode accessno ip address!interface FastEthernet1/4no ip addressshutdown!interface FastEthernet1/5no ip addressshutdown!interface FastEthernet1/6no ip addressshutdown!interface FastEthernet1/7no ip addressshutdown!interface FastEthernet1/8no ip addressshutdown!interface FastEthernet1/9switchportswitchport access vlan 51switchport mode accessno ip address!interface FastEthernet1/10no ip addressshutdown!interface FastEthernet1/11no ip addressshutdown!interface FastEthernet1/12no ip addressshutdown!interface FastEthernet1/13no ip addressshutdown!interface FastEthernet1/14no ip addressshutdown!interface FastEthernet1/15no ip addressshutdown!interface FastEthernet1/16no ip addressshutdown!interface FastEthernet1/17no ip addressshutdown!interface FastEthernet1/18no ip addressshutdown!interface FastEthernet1/19no ip addressshutdown!interface FastEthernet1/20no ip addressshutdown!interface FastEthernet1/21no ip addressshutdown!interface FastEthernet1/22no ip addressshutdown!interface FastEthernet1/23no ip addressshutdown!interface FastEthernet1/24no ip addressshutdown!interface FastEthernet1/25no ip addressshutdown!interface FastEthernet1/26no ip addressshutdown!interface FastEthernet1/27no ip addressshutdown!interface FastEthernet1/28no ip addressshutdown!interface FastEthernet1/29no ip addressshutdown!interface FastEthernet1/30no ip addressshutdown!interface FastEthernet1/31no ip addressshutdown!interface FastEthernet1/32no ip addressshutdown!interface FastEthernet1/33no ip addressshutdown!interface FastEthernet1/34no ip addressshutdown!interface FastEthernet1/35no ip addressshutdown!interface FastEthernet1/36no ip addressshutdown!interface FastEthernet1/37no ip addressshutdown!interface FastEthernet1/38no ip addressshutdown!interface FastEthernet1/39no ip addressshutdown!interface FastEthernet1/40no ip addressshutdown!interface FastEthernet1/41no ip addressshutdown!interface FastEthernet1/42no ip addressshutdown!interface FastEthernet1/43no ip addressshutdown!interface FastEthernet1/44no ip addressshutdown!interface FastEthernet1/45no ip addressshutdown!interface FastEthernet1/46no ip addressshutdown!interface FastEthernet1/47no ip addressshutdown!interface FastEthernet1/48no ip addressshutdown!interface GigabitEthernet2/1switchportswitchport access vlan 110switchport mode accessno ip address!interface GigabitEthernet2/2switchportswitchport access vlan 73switchport mode accessno ip address!interface GigabitEthernet2/3no ip addressshutdown!interface GigabitEthernet2/4no ip addressshutdown!interface GigabitEthernet2/5no ip addressshutdown!interface GigabitEthernet2/6no ip addressshutdown!interface GigabitEthernet2/7no ip addressshutdown!interface GigabitEthernet2/8no ip addressshutdown!interface GigabitEthernet2/9no ip addressshutdown!interface GigabitEthernet2/10no ip addressshutdown!interface GigabitEthernet2/11no ip addressshutdown!interface GigabitEthernet2/12no ip addressshutdown!interface GigabitEthernet2/13no ip addressshutdown!interface GigabitEthernet2/14no ip addressshutdown!interface GigabitEthernet2/15no ip addressshutdown!interface GigabitEthernet2/16no ip addressshutdown!interface GigabitEthernet5/1no ip addressshutdown!interface GigabitEthernet5/2no ip addressshutdown!interface GigabitEthernet6/1no ip addressshutdown!interface GigabitEthernet6/2no ip addressshutdown!interface GigabitEthernet9/1switchportswitchport trunk encapsulation dot1qswitchport trunk allowed vlan noneswitchport mode trunkmtu 4500no ip addressflowcontrol receive onflowcontrol send offspanning-tree portfast trunk!interface GigabitEthernet9/2switchportswitchport trunk encapsulation dot1qswitchport trunk allowed vlan 1,1002-1005switchport mode trunkmtu 4500no ip addressflowcontrol receive onflowcontrol send offspanning-tree portfast trunk!interface Vlan1no ip addressshutdown!interface Vlan71description PI Interfaceip address 71.0.0.254 255.0.0.0!interface Vlan73description To the Sup on the HA chassisip address 73.0.0.2 255.255.255.0standby 73 ip 73.0.0.73standby 73 name PDSN-SUP!interface Vlan110description RP Interfaceip address 41.0.0.252 255.0.0.0!ip classlessip route 7.0.0.82 255.255.255.255 71.0.0.82ip route 72.0.0.0 255.0.0.0 73.0.0.1ip route 82.0.0.0 255.0.0.0 71.0.0.82!no ip http server!snmp-server community public RO!!control-plane!!dial-peer cor custom!!!line con 0exec-timeout 0 0line vty 0 4exec-timeout 0 0privilege level 15password ciscologinline vty 5 15exec-timeout 0 0privilege level 15password ciscologin!!monitor event-trace timestampsno cns aaa enableendPDSN 1 Configuration
!! Last configuration change at 10:46:54 IST Fri Nov 11 2005!version 12.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryptionservice internalservice cdma pdsn!hostname mem82a!boot-start-markerboot-end-marker!!redundancy inter-devicescheme standby PDSN-SSP-SR!!redundancyenable password lab!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization ipmobile default group radiusaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting network pdsn start-stop group radius!!aaa session-id common!resource policy!!ipc zone defaultassociation 1no shutdownprotocol sctplocal-port 2000local-ip 41.0.1.82remote-port 2000remote-ip 41.0.2.82!clock timezone IST 5 30ip subnet-zerono ip gratuitous-arps!!ip cefno ip domain lookupno ip dhcp use vrf connected!!subscriber redundancy rate 500 1vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group 1! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 5.0.0.82l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 82.82.82.82 255.255.255.0!interface Loopback1ip address 7.0.0.82 255.255.255.0!interface CDMA-Ix1ip address 5.0.0.82 255.255.255.0tunnel source 5.0.0.82tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.51description To AAA Serverencapsulation dot1Q 51ip address 51.0.0.82 255.0.0.0no snmp trap link-status!interface GigabitEthernet0/0.71description PI Interfaceencapsulation dot1Q 71ip address 71.0.1.82 255.0.0.0no snmp trap link-statusstandby 182 ip 71.0.0.82standby 182 follow PDSN-SSP-SR!interface GigabitEthernet0/0.110description RP Interfaceencapsulation dot1Q 110ip address 41.0.1.82 255.0.0.0no snmp trap link-statusstandby 82 ip 41.0.0.82standby 82 name PDSN-SSP-SR!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool pdsn-pool 82.0.1.0 82.0.16.255ip local pool pdsn-pool 82.0.17.0 82.0.32.255ip local pool pdsn-pool 82.0.33.0 82.0.48.255ip local pool pdsn-pool 82.0.49.0 82.0.64.255ip local pool pdsn-pool 82.0.65.0 82.0.79.31ip classlessip route 72.0.0.0 255.0.0.0 71.0.0.254no ip http serverip mobile foreign-agent care-of Loopback1ip mobile foreign-service challengeip mobile foreign-service reverse-tunnelip mobile registration-lifetime 65535!!!snmp-server community public RO!!radius-server host 51.0.0.2 auth-port 1645 acct-port 1646 key ciscocdma pdsn pcf default closed-rpcdma pdsn accounting send start-stopcdma pdsn virtual-template 1cdma pdsn a10 max-lifetime 65535no cdma pdsn a10 gre sequencingcdma pdsn timeout a11-update 5cdma pdsn secure pcf default spi 100 key ascii cisco replay 200cdma pdsn secure cluster default spi 100 key ascii ciscocdma pdsn cluster member controller 41.0.0.41cdma pdsn cluster member interface GigabitEthernet0/0.110cdma pdsn cluster member queueingcdma pdsn redundancy!control-plane!line con 0exec-timeout 0 0line vty 0exec-timeout 0 0line vty 1 4line vty 5 15!!endPDSN 2 Configuration
!! Last configuration change at 12:35:50 IST Thu Nov 10 2005!version 12.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryptionservice internalservice cdma pdsn!hostname mem82b!boot-start-markerboot-end-marker!!redundancy inter-devicescheme standby PDSN-SSP-SR!!redundancyenable password lab!aaa new-model!!aaa authentication ppp default group radiusaaa authorization config-commandsaaa authorization ipmobile default group radiusaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting network pdsn start-stop group radius!!aaa session-id common!resource policy!!ipc zone defaultassociation 1no shutdownprotocol sctplocal-port 2000local-ip 41.0.2.82remote-port 2000remote-ip 41.0.1.82!clock timezone IST 5 30ip subnet-zerono ip gratuitous-arps!!ip cefno ip domain lookupno ip dhcp use vrf connected!!subscriber redundancy rate 500 1vpdn enablevpdn authen-before-forwardvpdn ip udp ignore checksum!vpdn-group 1! Default L2TP VPDN groupaccept-dialinprotocol l2tpsource-ip 5.0.0.82l2tp tunnel hello 0no l2tp tunnel authenticationl2tp tunnel timeout no-session never!no virtual-template snmp!!!interface Loopback0ip address 82.82.82.82 255.255.255.0!interface Loopback1ip address 7.0.0.82 255.255.255.0!interface CDMA-Ix1ip address 5.0.0.82 255.255.255.0tunnel source 5.0.0.82tunnel bandwidth transmit 0tunnel bandwidth receive 0!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.51description To AAA Serverencapsulation dot1Q 51ip address 51.0.0.182 255.0.0.0no snmp trap link-status!interface GigabitEthernet0/0.71description PI Interfaceencapsulation dot1Q 71ip address 71.0.2.82 255.0.0.0no snmp trap link-statusstandby 182 ip 71.0.0.82standby 182 follow PDSN-SSP-SR!interface GigabitEthernet0/0.110description RP Interfaceencapsulation dot1Q 110ip address 41.0.2.82 255.0.0.0no snmp trap link-statusstandby 82 ip 41.0.0.82standby 82 name PDSN-SSP-SR!interface Virtual-Template1ip unnumbered Loopback0peer default ip address pool pdsn-poolno keepaliveppp accm 0ppp authentication chap pap optionalppp accounting none!router mobile!ip local pool pdsn-pool 82.0.1.0 82.0.16.255ip local pool pdsn-pool 82.0.17.0 82.0.32.255ip local pool pdsn-pool 82.0.33.0 82.0.48.255ip local pool pdsn-pool 82.0.49.0 82.0.64.255ip local pool pdsn-pool 82.0.65.0 82.0.79.31ip classlessip route 72.0.0.0 255.0.0.0 71.0.0.254no ip http serverip mobile foreign-agent care-of Loopback1ip mobile foreign-service challengeip mobile foreign-service reverse-tunnelip mobile registration-lifetime 65535!!!snmp-server community public RO!!radius-server host 51.0.0.1 auth-port 1645 acct-port 1646 key ciscocdma pdsn pcf default closed-rpcdma pdsn accounting send start-stopcdma pdsn virtual-template 1cdma pdsn a10 max-lifetime 65535no cdma pdsn a10 gre sequencingcdma pdsn timeout a11-update 5cdma pdsn secure pcf default spi 100 key ascii cisco replay 200cdma pdsn secure cluster default spi 100 key ascii ciscocdma pdsn cluster member controller 41.0.0.41cdma pdsn cluster member interface GigabitEthernet0/0.110cdma pdsn cluster member queueingcdma pdsn redundancy!control-plane!line con 0exec-timeout 0 0line vty 0exec-timeout 0 0line vty 1 4line vty 5 15!!endSimple IPV6 Configuration Example
PDSN:pdsn2#sh runBuilding configuration...Current configuration : 4595 bytes!version 12.3no service padservice timestamps debug datetimeservice timestamps log datetimeno service password-encryptionservice cdma pdsn!hostname mwtcc21-pdsn2!boot-start-markerboot-end-marker!!redundancy inter-devicescheme standby pdsn-sr0!!redundancyno logging queue-limitenable password lab!aaa new-model!!aaa authentication ppp default local group radiusaaa authorization config-commandsaaa authorization network default group radiusaaa authorization configuration default group radiusaaa accounting update periodic 1aaa accounting network pdsn start-stop group radius!!aaa session-id common!resource manager!!ipc zone defaultassociation 1no shutdownprotocol sctplocal-port 5000local-ip 4.0.0.103remote-port 5000remote-ip 4.0.0.101!ip subnet-zero!!ip cefip cef accounting per-prefix non-recursiveip domain name cisco.comno ip dhcp use vrf connectedip dhcp ping packets 0!!ipv6 unicast-routingipv6 cef!no virtual-template snmp!!username pdsn2 password 0 cisco!!interface Loopback0ip address 6.0.0.1 255.0.0.0!interface Loopback2ip address 77.0.0.1 255.0.0.0!interface Loopback3ip address 3.0.0.1 255.0.0.0!interface CDMA-Ix1ip address 5.0.0.1 255.0.0.0tunnel source 5.0.0.1tunnel key 1tunnel sequence-datagrams!interface FastEthernet0/0ip address 10.77.154.236 255.255.255.192duplex autospeed auto!interface FastEthernet0/1ip address 86.0.0.2 255.0.0.0duplex autospeed auto!interface FastEthernet1/0ip address 22.22.22.3 255.0.0.0duplex fullno cdp enable!interface FastEthernet2/0ip address 88.0.0.4 255.0.0.0duplex halfstandby delay minimum 30 reload 60standby 12 ip 88.0.0.251standby 12 name pdsn-sr2!interface FastEthernet3/0ip address 4.0.0.103 255.0.0.0duplex autospeed autostandby delay minimum 30 reload 60standby 10 ip 4.0.0.254standby 10 name pdsn-sr0!interface FastEthernet3/1ip address 7.0.0.4 255.0.0.0duplex autospeed autostandby delay minimum 30 reload 60standby 11 ip 7.0.0.254standby 11 name pdsn-sr1!interface Ethernet4/0no ip addressduplex halfipv6 enable!interface Ethernet4/1ip address 66.0.0.2 255.0.0.0duplex halfipv6 address 2001::1/64ipv6 enable!interface Ethernet4/2no ip addressshutdownduplex half!interface Ethernet4/3no ip addressshutdownduplex half!interface Virtual-Template1ip unnumbered Loopback0ipv6 enableipv6 nd ra-interval 1000ipv6 nd ra-lifetime 5000no ipv6 nd suppress-rano keepalivecompress stacppp authentication chap pap optionalppp accounting none!router mobile!ip default-gateway 10.77.154.193ip classlessip route 9.0.0.2 255.255.255.255 86.0.0.1ip route 15.0.0.0 255.0.0.0 7.0.0.2ip route 19.0.0.0 255.0.0.0 7.0.0.2ip route 17.19.21.34 255.255.255.255 88.0.0.3ip mobile foreign-agent care-of Loopback2ip mobile foreign-service challenge forward-mfce timeout 10ip mobile foreign-service reverse-tunnelip mobile registration-lifetime 60000!no ip http serverno ip http secure-server!!ip radius source-interface Loopback3!!radius-server host 9.0.0.2 auth-port 1645 acct-port 1646 key ciscoradius-server vsa send accountingradius-server vsa send accounting 3gpp2cdma pdsn accounting send start-stopcdma pdsn virtual-template 1cdma pdsn a10 max-lifetime 65535cdma pdsn a10 ahdlc engine 0 usable-channels 8000cdma pdsn timeout mobile-ip-registration 300cdma pdsn send-agent-advcdma pdsn secure pcf 4.0.0.1 spi 100 key ascii ciscocdma pdsn secure pcf 4.0.0.2 spi 100 key ascii ciscocdma pdsn ipv6cdma pdsn redundancycdma pdsn redundancy accounting update-periodic!control-plane!!gatekeepershutdown!alias dhcp hu util ma hialias dhcp lu util ma loalias dhcp o30 origin dhcp subnet size initial /30 autogrow /30alias dhcp o29 origin dhcp subnet size initial /29 autogrow /29alias dhcp sp30 subnet prefix-length 30alias dhcp sp subnet prefix-lengthalias dhcp sp29 subnet prefix-length 29alias dhcp sp28 subnet prefix-length 28alias configure nopl no ip dhcp pool ispabc-odappoolalias configure cpool ip dhc poo ispabc-odappoolalias configure cpl ip dhc poo ispabc-odappoolalias exec shpl sh ip dhc pooalias exec shb sh ip dhc bin!line con 0exec-timeout 0 0stopbits 1line aux 0stopbits 1line vty 5 15!!endPDSN Accounting
The CDMA2000 packet accounting model is divided into radio specific parameters collected by the radio network elements, and the IP network specific parameters collected by the serving PDSN. In conformance with the packet accounting procedures specified in TIA/EIA/IS-835-B, the PDSN merges the radio specific parameters for a given user session with the IP network specific ones to form a Usage Data Record (UDR). After merging the parameters, the PDSN sends the UDR to the local RADIUS server at trigger events specified. The PDSN maintains the UDR until it receives positive acknowledgment from the RADIUS server indicating that the RADIUS server has correctly received the UDR.
Flow Based Accounting
The Cisco PDSN supports multiple user sessions per mobile station. Each of these user sessions is termed a flow. For each mobile station, one Simple IP based flow and one or more Mobile IP based flows can be supported. Each flow is identified by a unique IP address. Accounting procedures for generating a separate UDR for each flow is called flow based accounting.
The Cisco PDSN supports flow based accounting. As per TIA/EIA/IS-835-B specifications, each flow is identified by a unique Correlation-ID. Accounting start/stop message pair for each flow is correlated by unique Accounting-Session-ID.
While creating UDRs for flow based accounting, radio specific accounting parameters are common to all flows. IP network specific parameters, such as uplink and downlink octet counts are specific to each flow and are identified by the unique IP address assigned to that flow. The PDSN creates UDR for each flow by merging the radio specific parameters and the IP network specific parameters. These UDRs are forwarded to the RADIUS server via accounting-request (start, stop, interim) messages.
The following RADIUS attributes are contained in the UDR sent by PDSN.
The following list identifies the prepaid VSAs that can be included in the RADIUS attributes contained in the Accounting Stop Record:
•
•
•
•
•
•
•
•
•
AAA Authentication and Authorization Profile
This section describes User Profiles to be configured at the AAA server for authentication and authorization of users for various service types (Simple IP, Mobile IP, etc.). It also describes the minimal configuration required for the same.
1.
The client profile contains the ip address of the router and the shared key. The following example illustrates a client profile:
[ //localhost/Radius/Clients/username ]Name = usernameDescription =IPAddress = 9.15.68.7SharedSecret = labType = NASVendor =IncomingScript~ =OutgoingScript~ =UseDNIS = FALSEDeviceName =DevicePassword =2.
A user profile contains username, password, and the base profile where attributes retrieved during authorization can be configured.
The following example illustrates a user profile:
[ //localhost/Radius/UserLists/Default/username ]Name = usernameDescription =Password = <encrypted>AllowNullPassword = FALSEEnabled = TRUEGroup~ =BaseProfile~ = username-sipAuthenticationScript~ =AuthorizationScript~ =UserDefined1 =3.
The following example illustrates a base profile :
[ //localhost/Radius/Profiles/username-sip ]Name = username-sipDescription =Attributes/4.
[ //localhost/Radius/Profiles/username-sip/Attributes ]CDMA-IP-Technology = xAAA Profiles for Various Service Types
The following examples document AAA profiles for various service types such as SIP, MoIP, and others. The mandatory/optional attributes, and the attributes required to be configured for enabling different features, are specified.
Simple IP
CDMA-IP-Technology = x
The following attributes are optional and are needed only for specific scenarios:
•
Framed-IP-Address = 8.1.0.2
•
cisco-avpair = ip:addr-pool=pdsn-pool
•
cisco-avpair = "lcp:interface-config=compress stac"
cisco-avpair = "lcp:interface-config=compress mppc"
cisco-avpair = "lcp:interface-config=compress predictor"
•
Framed-Protocol = PPP
Framed-Routing = None
Service-Type = Framed
VPDN
cisco-avpair = vpdn:tunnel-type=l2tp
cisco-avpair = vpdn:ip-addresses=5.5.5.1
cisco-avpair = vpdn:l2tp-tunnel-password=cisco
The following configuration is optional at AAA contacted by LNS:
cisco-avpair = ip:addr-pool=pdsn-pool
MSID based Authentication
•
cisco-avpair = cdma:cdma-realm=cisco.com
CDMA-IP-Technology = x
•
cisco-avpair = lcp:cdma-user-class=3
cisco-avpair = cdma:cdma-realm=cisco.com
cisco-avpair = "lcp:spi#0 = spi 100 key ascii cisco"
cisco-avpair = lcp:cdma-ha-ip-addr=5.5.5.1
Proxy Mobile IP
cisco-avpair = lcp:cdma-ha-ip-addr=5.5.5.1
cisco-avpair = "lcp:spi#0 = spi 100 key ascii cisco"
cisco-avpair = lcp:cdma-user-class=3
Mobile IP
•
The following attributes are optional, and are only needed for specific scenarios:
–
CDMA-HA-IP-Addr = 6.0.0.2
–
cisco-avpair = "mobileip:spi#0=spi 100 key ascii cisco"
cisco-avpair = "mobileip:static-ip-addresses=20.0.0.1 20.0.0.2 20.0.0.3 20.0.0.4"
–
cisco-avpair = "mobileip:spi#0=spi 100 key ascii cisco"
cisco-avpair = "mobileip:static-ip-pool=mypool"
Prepaid (Optional)
•
Attributes
This section lists several of the various Accounting and Authentication attributes for the Cisco PDSN.
Authentication and Authorization RADIUS Attributes
The PDSN, Home Agent, and the RADIUS server support RADIUS attributes listed in Table 12 and Table 12 for authentication and authorization services.
Accounting Services RADIUS Attributes
The PDSN and the RADIUS server support the RADIUS attributes listed in Table 13 for accounting services. The inclusion of the various attributes in each of the accounting messages is detailed in the table. The inclusion, or not, of attributes in a message is not configurable.
Table 13 Accounting AVPs For Packet Data Services
Reference Specsstart
stop
interim
User-Name
B2
1
NA
64
string
Network Access Identifier (NAI) of the mobile user.
RFC 2865
Yes
Yes
Yes
NAS-IP- Address
D2
4
NA
4
IP addr
PDSN/FA address
RFC 2865
Yes
Yes
Yes
NAS-Port
NA
5
NA
4
integer
Port number on the PDSN used for com- municating with the RADIUS server
RFC 2865
Yes
Yes
Yes
Service-Type
NA
6
NA
4
integer
Type of service the user is getting.
Supported values:
•
•
RFC 2865
Yes
Yes
Yes
Framed- Protocol
NA
7
NA
4
integer
Framing protocol user is using.
Supported values:
•
RFC 2865
Yes
Yes
Yes
Framed-IP- Address
B1
8
NA
4
IP addr
IP address assigned to the user.
RFC 2865
Yes
Yes
Yes
Calling- Station-Id
A1
31
NA
15
string
MSID identifier of the mobile user.
RFC 2865
Yes
Yes
Yes
Acct-Status- Type
NA
40
NA
4
integer
Accounting record type
Supported Values:
•
•
•
•
•
RFC 2866
Yes
Yes
Yes
Acct-Delay- Time
NA
41
NA
4
integer
Number of seconds PDSN has been trying to send this accounting record.
RFC 2866
Yes
Yes
Yes
Acct-Input- Octets
G2
42
NA
4
integer
Total number of octets in IP packets send by the mobile user (verify)
RFC 2866
Yes
Yes
Yes
Acct-Output- Octets
G1
43
NA
4
integer
Total number of octets in IP packets send to the mobile user (verify)
RFC 2866
Yes
Yes
Yes
Acct-Session- Id
C1
44
NA
4
string
A unique accounting ID created by the PDSN that allows stop and start records to be matched in a log file.
RFC 2866
Yes
Yes
Yes
Acct- Authentic
NA
45
NA
4
integer
Method of authenticating the user
Supported values:
•
•
•
RFC 2866
Yes
Yes
Yes
Acct-Session Time
NA
46
NA
4
integer
Number of seconds user has received service.
RFC 2866
Yes
Yes
Yes
Acct-Input- Packets
NA
47
NA
4
integer
Number of packets sent from the mobile user (verify).
RFC 2866
Yes
Yes
Yes
Acct-Output- Packets
NA
48
NA
4
integer
Number of packets sent to the mobile user (verify).
RFC 2866
Yes
Yes
Yes
EventTime stamp
G4
55
NA
4
integer
Indicates start of accounting session or stop of accounting session if part of a RADIUS start message or stop message, respectively. It is also used in a RADIUS interim message to indicate the time of the event which triggered the interim message.
RFC 2869
Yes
Yes
Yes
NAS-Port- Type
NA
61
NA
4
integer
Type of physical port on the PDSN.
RFC 2865
Yes
Yes
Yes
Source Ipv6 Prefix
B#
97
NA
4-20
Ipv6-prefix
Carries the IPv6 prefix of the MS. The length includes the reserved byte as well as the prefix length field byte (see RFC 3162, section 2.3).
RFC3162
Yes
Yes
Yes
Ipv6 Interface ID
B4
96
NA
10
string
Interface ID of the mobile flow
RFC 3162
Yes
Yes
Yes
3GPP2-ESN
A2
26/52
3GPP2
15
string
ASCII string of ESN
IS-835-B
Yes
Yes
Yes
3GPP2-MEID
A3
26/116
3GPP2
14
string
ASCII string of MEID
IS-835-D
Yes
Yes
Yes
3GPP2-HA- IP-Addr
D1 4
26/7
3GPP2
4
ip-addr
IP address of the Home Agent
IS-835-B
Yes
Yes
Yes
3GPP2-PCF- IP-Addr
D3
26/9
3GPP2
4
ip-addr
IP address of the serving PCF
IS-835-B
Yes
Yes
Yes
3GPP2-BSID
D4
26/10
3GPP2
12
string
Base station ID
IS-835-B
Yes
Yes
Yes
3GPP2-User- Zone-ID
E1
26/11
3GPP2
4
integer
Tiered services user zone
IS-835-B
Yes
Yes
Yes
3GPP2- Forward-Mux- Option
F1
26/12
3GPP2
4
integer
Forward direction multiplex option
IS-835-B
Yes
Yes
Yes
3GPP2- Reverse-Mux- Option
F2
26/13
3GPP2
4
integer
Reverse direction multiplex option
IS-835-B
Yes
Yes
Yes
3GPP2- Service- Option
F5
26/16
3GPP2
4
integer
CDMA air interface service option
Supported values:
•
•
•
•
•
•
•
•
•
IS-835-B
Yes
Yes
Yes
3GPP2- Forward- Traffic-Type
F6
26/17
3GPP2
4
integer
Forward traffic type
Supported values:
•
•
IS-835-B
Yes
Yes
Yes
3GPP2- Reverse- Traffic-Type
F7
26/18
3GPP2
4
integer
Forward traffic type
Supported values:
•
•
IS-835-B
Yes
Yes
Yes
3GPP2- Fundamental- Frame-Size
F8
26/19
3GPP2
4
integer
Fundamental channel Frame Size
Supported values:
•
•
•
IS-835-B
Yes
Yes
Yes
3GPP2- Forward- Fundamental- RC
F9
26/20
3GPP2
4
integer
Forward Fundamental RC
Use is not yet specified in the specs.
IS-835-B
Yes
Yes
Yes
3GPP2- Reverse- Fundamental- RC
F10
26/21
3GPP2
4
integer
Reverse Fundamental RC.
Use is not yet specified in the specs.
IS-835-B
Yes
Yes
Yes
3GPP2-IP- Technology
F11
26/22
3GPP2
4
integer
Specifies Simple IP, Mobile IP, or other technology
Supported values:
•
•
Other values are configurable, but the defaults are as follows:
•
•
IS-835-B
Yes
Yes
Yes
3GPP2-Comp- Tunnel-Flag
F12
26/23
3GPP2
4
integer
Indicator of invocation of compulsory tunnel established on behalf of MS for providing private network and/or ISP access during a single packet data connection.
Supported values:
•
•
•
IS-835-B
Yes
Yes
Yes
3GPP2- Release- Indicator
F13
26/24
3GPP2
4
integer
Specifies reason for sending a Stop record.
Supported values:
•
•
•
•
•
IS-835-B
Yes
Yes
Yes
3GPP2-Bad- PPP-Frame- Count
G3
26/25
3GPP2
4
integer
Number of PPP frames from the mobile station dropped by PDSN due to un-correctable errors.
IS-835-B
Yes
Yes
Yes
3GPP2-Num- Active- Transitions
G9
26/30
3GPP2
4
integer
Number of dormant to active transitions by the user.
IS-835-B
Yes
Yes
Yes
3GPP2-SDB- Octet-Count- Terminating
G10
26/31
3GPP2
4
integer
Total number of octets sent to the user via Short Data Bursts.
IS-835-B
Yes
Yes
Yes
3GPP2-SDB- Octet-Count- Originating
G11
26/32
3GPP2
4
integer
Total number of octets sent by the user via Short Data Bursts.
IS-835-B
Yes
Yes
Yes
3GPP2-Num- SDB- Terminating
G12
26/33
3GPP2
4
integer
Total number of Short Data Burst transactions sent to the user
IS-835-B
Yes
Yes
Yes
3GPP2-Num- SDB- Originating
G13
26/34
3GPP2
4
integer
Total number of Short Data Burst transactions sent by the user.
IS-835-B
Yes
Yes
Yes
3GPP2-IP- QOS
l1
26/36
3GPP2
4
integer
Differentiated Services Code Points associated with the user data
Use is not yet specified in the specs.
IS-835-B
Yes
Yes
Yes
3GPP2- Airlink-QOS
l4
26/39
3GPP2
4
integer
Identifies airlink QoS associated with the user data.
Use is not yet specified in the specs.
IS-835-B
Yes
Yes
Yes
3GPP2-RP- Session-ID
Y2
26/41
3GPP2
4
integer
RP Session ID associated with user session
IS-835-B
Yes
Yes
Yes
3GPP2-Num- Bytes- Received- Total
G14
26/43
3GPP2
4
integer
Count of all bytes received in the reverse direction by the HDLC layer in PDSN.
IS-835-B
Yes
Yes
Yes
3GPP2- Correlation-ID
C2
26/44
3GPP2
8
integer
Identifies all the accounting sessions authorized for this NAI at a PDSN.
IS-835-B
Yes
Yes
Yes
3GPP2- MobileIP- InBound- Signaling- Count
G15
26/46
3GPP2
4
integer
Total number of octets in Registration Requests and Solicitations sent by the mobile.
IS-835-B
Yes
Yes
Yes
3GPP2- MobileIP- OutBound- Signaling- Count
G16
26/47
3GPP2
4
integer
Total number of octets in Registration Replies and advertisements sent to the mobile.
IS-835-B
Yes
Yes
Yes
3GPP2- Session- Continue
C3
26/48
3GPP2
4
integer
Session Continue Indicator to the RADIUS server.
Supported values:
•
•
IS-835-B
Yes
Yes
Yes
3GPP2-Active- Time
G8
26/49
3GPP2
4
integer
Total active connection time on traffic channel in seconds.
IS-835-B
Yes
Yes
Yes
3GPP2- DCCH- Frame-Format
F14
26/50
3GPP2
4
integer
Frame sizes on DCCH channel
Supported values:
•
•
•
•
IS-835-B
Yes
Yes
Yes
3GPP2-Always-On
F15
26/78
3GPP2
4
integer
Always On Service Indication.
Supported values:
•
•
IS-835-B
Yes1
Yes2
Yes3
1 F15 will be sent only when Always On service enabled for the user. However configuration option is provided to send it for all users.
2 F15 will be sent only when Always On service enabled for the user. However configuration option is provided to send it for all users.
3 F15 will be sent only when Always On service enabled for the user. However configuration option is provided to send it for all users.
Prepaid RADIUS Attributes
The following table describes the Prepaid specific attributes:
Mandatory AVPs in Connection Setup/Release Messages
Table 15 lists the
information elements carried in the Connection Setup and Release messages.
Q.931 Cause Codes Used in Call Disconnect Notify Message
The Call Disconnect Message uses Cause Code AVP to give additional information in case of unsolicited call disconnection. This AVP consists of Cause Code and a Cause Message field. The Cause Code field is always set to 0, any other value for Cause Code will cause the L2TP session to disconnect. The values for Cause Code and Cause Message defined by Q.931 standards are not sufficient, and Closed-RP defines the following the addition values for Call Management:
Glossary
1XRTT—Single Carrier, Radio Transmission Technology
1xEV-DO—Evolution-Data Optimized
3GPP2—3rd Generation Partnership Project 2
A10—3GPP2 TSG-A defined interface for user data
A11—3GPP2 TSG-A defined interface for control messages
AAA —Authentication, Authorization and Accounting
AH— Authentication Header
AHDLC—Asynchronous High-Level Data Link Control
APN— Access Point Name
BG —Border Gateway
BSC —Base Station Controller
BSS— Base Station Subsystem
BTS —Base Transceiver Station
CDMA—Code Division Multiple Access
CHAP— Challenge Handshake Authentication Protocol
CN—Corresponding Node
CoA— Care-Of-Address
CRB—Cisco Radius Billing (part of the VSA)
DES—Data Encryption Standard
DNS —Domain Name Server
EAP—Extensible Authentication Protocol
EIA—Electronic Industries Alliance
ESN— Electronic Serial Number
FA— Foreign Agent
FAC —Foreign Agent Challenge (also FA-CHAP)
GRE—Generic Routing Encapsulation
HA —Home Agent
HDLC— High-Level Data Link Control
HSRP —Hot Standby Router Protocol
IMSI—International Mobile Subscriber Identifier
IP —Internet Protocol
IPCP— IP Control Protocol
IS-835B—Specification of the CDMA2000 Wireless Data Architecture
ISP —Internet Service Provider
ITU —International Telecommunications Union
L2TP— Layer 2 Tunneling Protocol
LAC—L2TP Access Controller
LCP— Link Control Protocol
LNS —L2TP Network Server
MAC —Medium Access Control
MEID—Mobile Equipment Identifier
MIB—Management Information Base
MIN—Mobile Identification Number
MIP— Mobile IP
MS— Mobile Station (= TE + MT)
MSID—Mobile Station Identification
MT —Mobile Termination
MWAM—Multi-processor WAN Application Module
NAI —Network Access Identifier
NAS —Network Access Server
P-MIP— Proxy-Mobile IP
PAP— Password Authentication Protocol
PCF— Packet Control Function
PDSN —Packet Data Serving Node
PPP— Point-to-Point Protocol
PPTP— Point-to-Point Tunneling Protocol
RADIUS—Remote Authentication Dial-in User Service
RAN—Radio Access Network
RP—Radio-PDSN Interface
SDB—Short Data Burst
SIP—Simple IP
SNMP—Simple Network Management Protocol
SPI Value—Security Parameter Index Value
TE —Terminal Equipment
TIA—Telecommunications Industry Association
TID —Tunnel Identifier
UDR—Usage Data Record
UDP—User Datagram Protocol
VPDN —Virtual Packet Data Network
VSA—Vendor Specific Attribute
WAP —Wireless Application Protocol
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0711R)
Copyright © 2007, Cisco Systems, Inc.
All rights reserved.
FeedbackContact Cisco
- Open a Support Case
- (Requires a Cisco Service Contract)