Cisco Unified Border Element (Enterprise) Management Configuration Guide, Cisco IOS XE Release 3S
Finding Feature Information
Downloads: This chapterpdf (PDF - 1.24MB) The complete bookPDF (PDF - 2.77MB) | The complete bookePub (ePub - 424.0KB) | Feedback

Finding Feature Information

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information about PCM Audio Capture

PCM Audio Capture

The following are the enhancements to the PCM Audio Capture feature:

  • Separate PCM capture and Banjo logger feature so that they do not share the same data (.dat) file; they have their own data file.
  • One PCM call per data file is generated dynamically. The filename contains information such as voice port type and number, call ID, calling and called number, GUID, DSP channel number, and time stamp.
  • A user on the TDM-TDM or TDM-VoIP call can dynamically enable and disable PCM capture by entering predefined start and stop Dual Tone Multi-Frequency (DTMF) digits.
  • More test points or streams can be captured.

Note


PCM capture is a CPU-intensive feature, and you must not enable several PCM capture sessions while running heavy traffic.


How to Configure PCM Audio Capture

Configuring PCM Audio Capture

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    voice pcm capture buffer number

    4.    voice pcm capture destination url

    5.    voice pcm capture on-demand-trigger

    6.    voice pcm capture user-trigger-string start-string stop-string stream bitmap duration call-duration

    7.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
                Router> enable
              
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2configure terminal


    Example:
    Router# configure terminal
              
     

    Enters global configuration mode.

     
    Step 3voice pcm capture buffer number


    Example:
    Router(config)# voice pcm capture buffer 10
              
     

    Configures the number of PCM capture buffers. The Range is from 0 to 200000. To change the PCM capture buffer size, you must first configure it with 0 and then configure it with the desired number.

     
    Step 4voice pcm capture destination url


    Example:
    Router(config)# voice pcm capture destination tftp://10.10.1.2/acphan/
              
     

    Configures or changes the destination URL for storing captured data.

     
    Step 5voice pcm capture on-demand-trigger


    Example:
    Router(config)# voice pcm capture on-demand-trigger
              
     

    Configures user-triggered PCM capture.

     
    Step 6voice pcm capture user-trigger-string start-string stop-string stream bitmap duration call-duration


    Example:
    Router(config)# voice pcm capture #132 #543 stream ff duration 230
              
     

    Changes the default user trigger PCM capture start and stop string, stream, and duration.

    • The start and stop string must have different values.
    • PCM stream bitmap is in hexadecimal. The range is from 1 to FFFFFFF.
    • The stream bitmap definitions are as follows:
      • bit 0—Rin
      • bit 1—Sin
      • bit 2—Sout
      • bit 3—nonNLP Sout
      • bit 4—fax modem in
      • bit 5—fax modem out
      • bit 6—from IP network to TDM earpiece direction: ASP input
      • bit 7—from IP network to TDM earpiece direction: ASP output
      • bit 8—NR in
      • bit 9—NR out
      • bit 10—from TDM mic to IP network: ASP in
      • bit 11—from TDM mic to IP network: ASP out
     
    Step 7end


    Example:
    Router(config)# end
              
     

    Returns to privileged EXEC mode.

     

    Verifying PCM Audio Capture

    Perform this task to verify the configuration for the PCM Audio Capture feature.

    SUMMARY STEPS

      1.    enable

      2.    show voice pcm capture


    DETAILED STEPS
      Step 1   enable


      Example:
      Router> enable
                

      Enables privileged EXEC mode.

      Step 2   show voice pcm capture


      Example:
      Router# show voice pcm capture
      
      PCM Capture is on and is logging to URL tftp://10.10.1.2/acphan/
      50198 messages sent to URL, 0 messages dropped
      Message Buffer (total:inuse:free) 200000:0:200000
      Buffer Memory: 68000000 bytes, Message size: 340 bytes
                

      Displays the configured PCM capture buffer and destination, number of saved messages/packets, number of dropped messages/packets, and number of buffers allocated, both used and free.


      Feature Information for Pulse Code Modulation (PCM) Audio Capture

      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

      Table 1 Feature Information for Pulse Code Modulation (PCM) Audio Capture

      Feature Name

      Releases

      Feature Information

      Pulse Code Modulation (PCM) Audio Capture

      15.2(2)T

      The PCM Capture feature is used for debugging audio quality issues.

      In Cisco IOS Release 15.2(2)T, this feature was implemented on the Cisco Unified Border Element .

      The following commands were introduced or modified: show voice pcm capture, voice pcm capture.

      Pulse Code Modulation (PCM) Audio Capture

      Cisco IOS XE Release 3.6S

      The PCM Capture feature is used for debugging audio quality issues.

      In Cisco IOS XE Release 3.6S, this feature was implemented on the Cisco Unified Border Element (Enterprise)

      The following commands were introduced or modified: show voice pcm capture, voice pcm capture.