QoS: Classification Configuration Guide, Cisco IOS XE Release 3S
QoS Match VLAN
Downloads: This chapterpdf (PDF - 1.14MB) The complete bookPDF (PDF - 3.12MB) | The complete bookePub (ePub - 366.0KB) | Feedback

QoS Match VLAN

QoS Match VLAN

The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information About Match VLAN

QoS Match VLAN

The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number. To classify network traffic based on the VLAN identification number you create a class-map and specify the match criteria using the match vlan command. You then attach the class to a policy-map and use the policy map in a service policy that is attached to an interface.

How to Configure Match VLAN

Classifying Network Traffic per VLAN

To classify network traffic on a per VLAN basis, perform the following task.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    class-map {match-any | match-all} class-map-name

    4.    match vlan vlan-id-number

    5.    exit

    6.    policy-map policy-map-name

    7.    class class-map-name

    8.    bandwidth percent percent

    9.    exit

    10.    exit

    11.    policy-map policy-map-name

    12.    class class-map-name

    13.    shape {average | peak} cir

    14.    service-policy {input | output} policy-map-name

    15.    exit

    16.    exit

    17.    interface type number [name-tag]

    18.    service-policy {input | output} policy-map-name

    19.    end


DETAILED STEPS
      Command or Action Purpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 class-map {match-any | match-all} class-map-name


    Example:
    Router(config)# class-map match-any Blue_VRF
     

    Creates a class map and enters class map configuration mode.

     
    Step 4 match vlan vlan-id-number


    Example:
    Router(config-cmap)# match vlan 101
     

    Matches traffic on the basis of the range of VLAN identification numbers specified.

     
    Step 5 exit


    Example:
    Router(config-cmap)# exit
     

    Returns to global configuration mode.

     
    Step 6 policy-map policy-map-name


    Example:
    Router(config)# policy-map Shared_QoS
     

    Creates a policy map that can be attached to an interface and enters policy-map configuration mode.

     
    Step 7 class class-map-name


    Example:
    Router(config-pmap)# class Blue_VRF
     

    Specify the name of the class whose policy you want to create and enters policy-map class configuration mode.

     
    Step 8 bandwidth percent percent


    Example:
    Router(config-pmap-c)# bandwidth percent 30
     

    Specifies the bandwidth allocated for a class belonging to a policy map.

     
    Step 9 exit


    Example:
    Router(config-pmap-c)# exit
     

    Returns to policy-map configuration mode.

     
    Step 10 exit


    Example:
    Router(config-pmap)# exit
     

    Returns to global configuration mode.

     
    Step 11 policy-map policy-map-name


    Example:
    Router(config)# policy-map COS-OUT-SHAPED
     

    Creates a policy map that can be attached to an interface and enters policy-map configuration mode.

     
    Step 12 class class-map-name


    Example:
    Router(config-pmap)# class FROM_WAN
     

    Specify the name of the class whose policy you want to create and enters policy-map class configuration mode.

     
    Step 13 shape {average | peak} cir


    Example:
    Router(config-pmap-c)# shape average 9000000000
     
    Specifies the average rate traffic shaping.
    • The Committed information rate (CIR), is specified in bits per second (bps).
     
    Step 14 service-policy {input | output} policy-map-name


    Example:
    Router(config-pmap-c)# service-policy Shared_QoS
     

    Specifies the name of the predefined policy map to be used as a QoS policy.

     
    Step 15 exit


    Example:
    Router(config-pmap-c)# exit
     

    Returns to policy-map configuration mode.

     
    Step 16 exit


    Example:
    Router(config-pmap)# exit
     

    Returns to global configuration mode.

     
    Step 17 interface type number [name-tag]


    Example:
    Router(config)# interface FastEthernet 0/0.1
     

    Configures an interface type and enters interface configuration mode.

    • Enter the interface type and number.
     
    Step 18 service-policy {input | output} policy-map-name


    Example:
    Router(config-if)# service-policy output COS-OUT-SHAPED
     

    Attaches a policy map to an input interface, a virtual circuit (VC), an output interface, or a VC that will be used as the service policy for the interface.

     
    Step 19 end


    Example:
    Router(config-if)# end
     

    (Optional) Exits interface configuration mode and returns to privileged EXEC mode.

     

    Configuration Examples for Match VLAN

    Example: Classifying Network Traffic per VLAN

    The following example shows how to classify network traffic on a VLAN basis. The VLAN classified traffic is applied to the FastEthernet 0/0.1 subinterface.

    interface FastEthernet0/0.1
    service-policy output COS-OUT-SHAPED
    policy-map COS-OUT-SHAPED
          class ADMIN
          class FROM_WAN
                   shape average 900000000
                   service-policy Shared_QoS
    policy-map Shared_QoS
          ! description -- Bandwidth sharing between VRF --
          class Blue_VRF
                   bandwidth percent 3
    class-map match-any Blue_VRF
          ! description -- traffic belonging to the VRF Blue --
          match vlan  101
          

    Additional References for QoS for Match VLAN

    Related Documents

    Related Topic

    Document Title

    Cisco commands

    Cisco IOS Master Command List, All Releases

    QoS commands: complete command syntax, command modes, command history, defaults, usage guidelines, and examples

    Cisco IOS Quality of Service Solutions Command Reference

    Classifying network traffic

    “Classifying Network Traffic” module

    MQC

    “Applying QoS Features Using the MQC” module

    Marking network traffic

    “Marking Network Traffic” module

    Technical Assistance

    Description

    Link

    The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

    Feature Information for QoS for Match VLAN

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Table 1 Feature Information for QoS for Match VLAN

    Feature Name

    Releases

    Feature Information

    QoS: Match VLAN

    12.2(31)SB2

    Cisco IOS XE Release 2.1

    15.0(1)S

    The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number. The following commands were introduced or modified by this feature: match vlan (QoS), show policy-map interface
    Note   

    As of Cisco IOS Release 12.2(31)SB2, the QoS: Match VLAN feature is supported on Cisco 10000 series routers only.

    This feature was introduced on Cisco ASR 1000 Series Routers.