--The usage of NHOP and NNHOP backup tunnels to provide bandwidth protection for rerouted LSPs.
--An MPLS TE tunnel used to protect other (primary) tunnels’ traffic when a link or node failure occurs.
--The available traffic capacity of a link.
--A means for accelerating the forwarding of packets within a router, by storing route lookup.
--A large and diverse network connecting most major points in a company or other organization.
--Procedures that enable temporary routing around a failed link or node while a new LSP is being established at the headend.
--The total bandwidth allocated to an MPLS traffic engineering link or node.
--The router that originates and maintains a given LSP. This is the first router in the LSP’s path.
--Passage of a data packet between two network nodes (for example, between two routers).
--A Hello instance implements the RSVP Hello extensions for a given router interface address and remote IP address. Active Hello instances periodically send Hello Request messages, expecting Hello ACK messages in response. If the expected ACK message is not received, the active Hello instance declares that the neighbor (remote IP address) is unreachable (that is, it is lost). This can cause LSPs crossing this neighbor to be fast rerouted.
--A network connection.
--IS-IS. Link-state hierarchical routing protocol that calls for intermediate system (IS) routers to exchange routing information based on a single metric to determine network topology.
--A point-to-point connection between adjacent nodes. There can be more than one link between adjacent nodes. A link is a network communications channel consisting of a circuit or transmission path and all related equipment between a sender and a receiver. Sometimes referred to as a line or a transmission link.
--Backup tunnels that provide bandwidth protection.
--A configuration technique that shifts traffic to an alternative link if a certain threshold is exceeded on the primary link. Load balancing is similar to redundancy in that if an event causes traffic to shift directions, alternative equipment must be present in the configuration. In load balancing, the alternative equipment is not necessarily redundant equipment that operates only in the event of a failure.
--label-switched path. A connection between two routers in which MPLS forwards the packets.
--The backup tunnel’s tail.
--Multiprotocol Label Switching. Packet-forwarding technology, used in the network core, that applies data link layer labels to tell switching nodes how to forward data, resulting in faster and more scalable forwarding than network layer routing normally can do.
--There is one label space for all interfaces in the router. For example, label 100 coming in one interface is treated the same as label 100 coming in a different interface.
--next hop. The next downstream node along an LSP’s path.
--next-hop backup tunnel. Backup tunnel terminating at the LSP’s next hop beyond the point of failure, and originating at the hop immediately upstream of the point of failure. It bypasses a failed link, and is used to protect primary LSPs that were using this link before the failure.
--next-next hop. The node after the next downstream node along an LSP’s path.
--next-next-hop backup tunnel. Backup tunnel terminating at the LSP’s next-next hop beyond the point of failure, and originating at the hop immediately upstream of the point of failure. It bypasses a failed link or node, and is used to protect primary LSPs that were using this link or node before the failure.
--Endpoint of a network connection or a junction common to two or more lines in a network. Nodes can be interconnected by links, and serve as control points in the network. Nodes can be processors, controllers, or workstations.
--Open Shortest Path First. A link-state hierarchical Interior Gateway Protocol routing algorithm, derived from the IS-IS protocol. OSPF features include least-cost routing, multipath routing, and load balancing.
--The last LSP originally signaled over the protected interface before the failure. The primary LSP is the LSP before the failure.
--Tunnel whose LSP may be fast rerouted if there is a failure. Backup tunnels cannot be primary tunnels.
--Conditions, such as a new backup tunnel comes up, cause a reevaluation of a backup tunnel that was chosen for an LSP. If the reevaluation is successful, it is called a promotion.
--An interface that has one or more backup tunnels associated with it.
--The duplication of devices, services, or connections so that, in the event of a failure, the redundant devices, services, or connections can perform the work of those that failed.
--Resource Reservation Protocol. A protocol used for signaling requests (setting up reservations) for Internet services by a customer before that customer is permitted to transmit data over that portion of the network.
--An indicator showing how quickly some measure of resource usage increases as a network gets larger.
--shared risk link group. Sets of links that are likely to go down together.
--Information that a router must maintain about each LSP. The information is used for rerouting tunnels.
--The more restrictive bandwidth in an MPLS traffic engineering link or node. The subpool is a portion of the link or node’s overall global pool bandwidth.
--The router upon which an LSP is terminated. This is the last router in the LSP’s path.
--The physical arrangement of network nodes and media within an enterprise networking structure.
--Secure communications path between two peers, such as two routers.
--Backup tunnels that provide no bandwidth (best-effort) protection (that is, they provide best-effort protection).