IP Mobility: Mobile IP Configuration Guide, Cisco IOS XE Release 3S (Cisco ASR 1000)
Proxy Mobile IPv6 Support for MAG Functionality
Downloads: This chapterpdf (PDF - 1.42MB) The complete bookPDF (PDF - 2.51MB) | Feedback

Proxy Mobile IPv6 Support for MAG Functionality

Contents

Proxy Mobile IPv6 Support for MAG Functionality

The Proxy Mobile IPv6 Support for MAG Functionality feature provides network-based IP Mobility management to a mobile node (MN) without requiring the participation of the mobile node in any IP Mobility-related signaling. The Mobile Access Gateway (MAG) tracks the movements of the MN to and from an access link and sends signals to the local mobility anchor of the MN.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Proxy Mobile IPv6 Support for MAG Functionality

The DHCP server must be configured.

Information About Proxy Mobile IPv6 Support for MAG Functionality

Proxy Mobile IPv6 Overview

Proxy Mobile IPv6 (PMIPv6) provides network-based IP Mobility management to a mobile node (MN), without requiring the participation of the MN in any IP mobility-related signaling. The mobility entities in the network track the movements of the MN, initiate the mobility signaling, and set up the required routing state.

The major functional entities of PMIPv6 are Mobile Access Gateways (MAGs), Local Mobility Anchors (LMAs), and MNs.

Mobile Access Gateways

A Mobile Access Gateway (MAG) performs mobility-related signaling on behalf of the mobile nodes (MN) attached to its access links. MAG is the access router for the MN; that is, the MAG is the first-hop router in the localized mobility management infrastructure.

A MAG performs the following functions:

  • Obtains an IP address from a Local Mobility Anchor (LMA) and assigns it to an MN
  • Retains the IP address of an MN when the MN roams across MAGs
  • Tunnels traffic from an MN to LMA

Local Mobility Anchor

Local Mobility Anchor (LMA) is the home agent for a mobile node (MN) in a Proxy Mobile IPv6 (PMIPv6) domain. It is the topological anchor point for MN home network prefixes and manages the binding state of an MN. An LMA has the functional capabilities of a home agent as defined in the Mobile IPv6 base specification (RFC 3775) along with the capabilities required for supporting the PMIPv6 protocol.


Note


Use an dynamic mag learning command to enable an LMA to accept Proxy Mobile IPv6 (PMIPv6) signaling messages from any Mobile Access Gateway (MAG) that is not locally configured.


Mobile Node

A mobile node (MN) is an IP host whose mobility is managed by the network. An MN can be an IPv4-only node, an IPv6-only node, or a dual-stack node, which is a node with IPv4 and IPv6 protocol stacks. An MN is not required to participate in any IP mobility-related signaling for achieving mobility for an IP address or a prefix that is obtained in the Proxy Mobile IPv6 (PMIPv6) domain.

AAA Server Attributes for Proxy Mobile IPv6

If an authentication, authorization, and accounting (AAA) server is available, a Mobile Access Gateway (MAG) obtains the profile information of the Proxy Mobile IPv6 (PMIPv6) domain and the mobile node (MN) from the server during the configuration and call-flow time, respectively.

The following are the AAA attributes required for configuring the PMIPv6 domain and the MN are:

  • PMIPv6 domain-specific AAA attributes:
    • cisco-mpc-protocol-interface
    • lma-identifier
    • mag-identifier
    • mag-v4-address
    • mag-v6-address
    • pmip6-domain-identifier
    • pmip6-fixed-l1-address
    • pmip6-fixed-l2-address
    • pmip6-timestamp-window
    • pmip6-replay-protection
    • pmip6-spi-key
    • pmip6-spi-value
  • MN-specific AAA attributes:
    • home-lma
    • home-lma-ipv6-address
    • mn-apn
    • mn-nai
    • mn-network
    • mn-service
    • multihomed

How to Configure Proxy Mobile IPv6 Support for MAG Functionality

Configuring a Proxy Mobile IPv6 Domain by Using the Configuration from the AAA Server

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ipv6 mobile pmipv6-domain domain-name load-aaa

    4.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 ipv6 mobile pmipv6-domain domain-name load-aaa


    Example:
    Device(config)# ipv6 mobile pmipv6-domain D1 load-aaa
     

    Creates a PMIPv6 domain and configures it by using the configuration from the AAA server.

     
    Step 4 end


    Example:
    Device(config)# end
     

    Exits global configuration mode and returns to privileged EXEC mode.

     

    Configuring the Minimum Configuration for a MAG to Function

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ipv6 mobile pmipv6-domain domain-name

      4.    lma lma-id

      5.    ipv6-address ipv6-address

      6.    exit

      7.    Repeat Steps 5 to 8 to configure the second LMA.

      8.    nai [user]@realm

      9.    lma lma-id

      10.    service {dual | ipv4 | ipv6}

      11.    exit

      12.    Repeat Steps 10 to 11 to configure the second MN.

      13.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.
       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 ipv6 mobile pmipv6-domain domain-name


      Example:
      Device(config)# ipv6 mobile pmipv6-domain dn1
       

      Creates the Proxy Mobile IPv6 (PMIPv6) domain and enters PMIPv6 domain configuration mode.

       
      Step 4 lma lma-id


      Example:
      Device(config-ipv6-pmipv6-domain)# lma lma1
       

      Configures an Local Mobility Anchor (LMA) within the PMIPv6 domain and enters PMIPv6 domain LMA configuration mode.

       
      Step 5 ipv6-address ipv6-address


      Example:
      Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:DB8::1
       

      Configures an IPv6 address for the LMA within the PMIPv6 domain.

       
      Step 6 exit


      Example:
      Device(config-ipv6-pmipv6-domain-lma)# exit
       

      Exits PMIPv6 domain LMA configuration mode and returns to PMIPv6 domain configuration mode.

       
      Step 7 Repeat Steps 5 to 8 to configure the second LMA.  

       
      Step 8 nai [user]@realm


      Example:
      Device(config-ipv6-pmipv6-domain)# nai user1@example.com
       

      Configures a network access identifier for the mobile node (MN) within the PMIPv6 domain and enters PMIPv6 domain mobile node configuration mode.

       
      Step 9 lma lma-id


      Example:
      Device(config-ipv6-pmipv6-domain-mn)# lma lma1
       

      Configures an LMA for the MN.

       
      Step 10 service {dual | ipv4 | ipv6}

      Example:
      Device(config-ipv6-pmipv6-domain-mn)# service ipv4
       

      Configures the service provided to the MN within the PMIPv6 domain.

      The type of services provided to the MN are as follows:

      • dual—Specifies both IPv4 and IPv6 services for an MN.
      • IPv4—Specifies IPv4 service for an MN.
      • IPv6—Specifies IPv6 service for an MN.
       
      Step 11 exit


      Example:
      Device(config-ipv6-pmipv6-domain-mn)# exit
       

      Exits PMIPv6 domain mobile node configuration mode and returns to PMIPv6 domain configuration mode.

       
      Step 12 Repeat Steps 10 to 11 to configure the second MN.  

       
      Step 13 end


      Example:
      Device(config-ipv6-pmipv6-domain)# end
       

      Exits PMIPv6 domain configuration mode and returns to privileged EXEC mode.

       

      Configuring a Detailed Configuration for a MAG When an AAA Server Is Not Available

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    ipv6 mobile pmipv6-domain domain-name

        4.    replay-protection timestamp [window seconds]

        5.    auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii ascii-string | hex hex-string}

        6.    encap {gre-ipv4 | ipv6-in-ipv6}

        7.    local-routing-mag

        8.    lma lma-id

        9.    ipv6-address ipv6-address

        10.    exit

        11.    Repeat Steps 10 to 12 to configure each LMA.

        12.    mag mag-id

        13.    ipv6-address ipv6-address

        14.    exit

        15.    mn-profile-load-aaa

        16.    nai [user]@realm

        17.    lma lma-id

        18.    int att interface-access-type l2-addr mac-address

        19.    gre-encap-key [down | up] key-value

        20.    service {dual | ipv4 | ipv6}

        21.    apn apn-name

        22.    exit

        23.    Repeat Steps 20 to 24 to configure each MN.

        24.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.
         
        Step 2 configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 ipv6 mobile pmipv6-domain domain-name


        Example:
        Device(config)# ipv6 mobile pmipv6-domain dn1
         

        Creates a Proxy Mobile IPv6 (PMIPv6) domain and enters PMIPv6 domain configuration mode.

         
        Step 4 replay-protection timestamp [window seconds]


        Example:
        Device(config-ipv6-pmipv6-domain)# replay-protection timestamp window 200
         

        Configures the replay protection mechanism within the PMIPv6 domain.

         
        Step 5 auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii ascii-string | hex hex-string}


        Example:
        Device(config-ipv6-pmipv6-domain)# auth-option spi 67 key ascii key1
         

        Configures authentication for the PMIPv6 domain.

         
        Step 6 encap {gre-ipv4 | ipv6-in-ipv6}


        Example:
        Device(config-ipv6-pmipv6-domain)# encap gre-ipv4
         

        Configures the tunnel encapsulation mode type between the Mobile Access Gateway (MAG) and the Local Mobility Anchor (LMA).

         
        Step 7 local-routing-mag


        Example:
        Device(config-ipv6-pmipv6-domain)# local-routing-mag
         

        Enables local routing for the MAG.

         
        Step 8 lma lma-id


        Example:
        Device(config-ipv6-pmipv6-domain)# lma lma1
         

        Configures LMA within the PMIPv6 domain and enters PMIPv6 domain LMA configuration mode.

         
        Step 9 ipv6-address ipv6-address


        Example:
        Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:3::1
         

        Configures an IPv6 address for the LMA within the PMIPv6 domain.

         
        Step 10 exit


        Example:
        Device(config-ipv6-pmipv6-domain-lma)# exit
         

        Exits PMIPv6 domain LMA configuration mode and returns to PMIPv6 domain configuration mode.

         
        Step 11 Repeat Steps 10 to 12 to configure each LMA.  

         
        Step 12 mag mag-id


        Example:
        Device(config-ipv6-pmipv6-domain)# mag mag1
         

        Configures a MAG within the PMIPv6 domain and enters PMIPv6 domain MAG configuration mode.

         
        Step 13 ipv6-address ipv6-address


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:0DB8:2:4::1
         

        Configures an IPv6 address for the MAG within the PMIPv6 domain.

         
        Step 14 exit


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# exit
         

        Exits PMIP domain MAG configuration mode and returns to PMIPv6 domain configuration mode.

         
        Step 15 mn-profile-load-aaa


        Example:
        Device(config-ipv6-pmipv6-domain)# mn-profile-load-aaa
         

        (Optional) Loads the profile configuration from AAA to the mobile node (MN) within the PMIPv6 domain.

        Note   

        Steps 20 to 24 need not be entered if the MN is configured using the configuration from AAA. You can use the specific command to override the configuration for a specific mobile node (MN) parameter.

         
        Step 16 nai [user]@realm


        Example:
        Device(config-ipv6-pmipv6-domain)# nai user1@example.com
         

        Configures the network address identifier (NAI) for the MN within the PMIPv6 domain and enters PMIPv6 domain MN configuration mode.

         
        Step 17 lma lma-id


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# lma lma1
         

        Configures the LMA for the MN.

         
        Step 18 int att interface-access-type l2-addr mac-address


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# int att Gigabitethernet l2-addr 02c7.f800.0422
         

        Configures the access technology type, interface, and MAC address of the MN interface within the PMIPv6 domain.

         
        Step 19 gre-encap-key [down | up] key-value


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# gre-encap-key down 45
         

        Configures a generic routing encapsulation (GRE) key for the MN within the PMIPv6 domain.

         
        Step 20 service {dual | ipv4 | ipv6}

        Example:
        Device(config-ipv6-pmipv6-domain-mn)# service ipv4
         

        Configures the service provided to the MN within the PMIPv6 domain.

        The type of services provided to the MN are as follows:

        • dual—Specifies both IPv4 and IPv6 services for an MN.
        • IPv4—Specifies an IPv4 service for an MN.
        • IPv6—Specifies an IPv6 service for an MN.
         
        Step 21 apn apn-name


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# apn apn1
         

        Specifies an access point name (APN) to the MN subscriber within the PMIPv6 domain.

         
        Step 22 exit


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# exit
         

        Exits PMIP domain MN configuration mode and returns to PMIPv6 domain configuration mode.

         
        Step 23 Repeat Steps 20 to 24 to configure each MN.  

         
        Step 24 end


        Example:
        Device(config-ipv6-pmipv6-domain)# end
         

        Exits PMIPv6 domain configuration mode and returns to privileged EXEC mode.

         

        Configuring a Minimum Configuration for a MAG

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    ipv6 mobile pmipv6-mag mag-id domain domain-name

          4.    address ipv6 ipv6-address

          5.    sessionmgr

          6.    generate grekey

          7.    interface type number

          8.    role {3gpp | lte | wimax | wlan}

          9.    apn apn-name

          10.    end


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.
           
          Step 2 configure terminal


          Example:
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 ipv6 mobile pmipv6-mag mag-id domain domain-name


          Example:
          Device(config)# ipv6 mobile pmipv6-mag mag1 domain dn1
           

          Enables the MAG service on a device, configures the PMIPv6 domain for the MAG, and enters MAG configuration mode.

           
          Step 4 address ipv6 ipv6-address


          Example:
          Device(config-ipv6-pmipv6-mag)# address ipv6 2001:0DB8:2:4::1
           

          Configures an IPv6 address for the MAG.

           
          Step 5 sessionmgr


          Example:
          Device(config-ipv6-pmipv6-mag)# sessionmgr
           

          Enables the MAG to process the the notification it receives through the mobile client service abstraction (MCSA) from the Intelligent Services Gateway (ISG).

           
          Step 6 generate grekey


          Example:
          Device(config-ipv6-pmipv6-mag)# generate grekey
           

          Enables dynamic generation of upstream generic routing encapsulation keys for mobile nodes in an LMA.

           
          Step 7 interface type number


          Example:
          Device(config-ipv6-pmipv6-mag)# interface gigabitethernet 0/0/0
           

          Enables an interface for the MAG.

           
          Step 8 role {3gpp | lte | wimax | wlan}


          Example:
          Device(config-ipv6-pmipv6-mag)# role lte
           

          Configures a role for the MAG.

          The keywords are as follows:

          • 3gpp—Specifies the role as the 3rd Generation Partnership Project (3GPP).
          • lte—Specifies the role as Long Term Evaluation (LTE).
          • wimax—Specifies the role as wimax.
          • wlan—Specifies the role as wireless LAN (WLAN).
           
          Step 9 apn apn-name


          Example:
          Device(config-ipv6-pmipv6-mag)# apn apn2
           

          Specifies an access point name (APN) to the subscriber of the MAG.

          Note   

          Specifying an APN is mandatory if the role of the MAG is 3GPP.

           
          Step 10 end


          Example:
          Device(config-ipv6-pmipv6-mag)# end
           

          Exits MAG configuration mode and returns to privileged EXEC mode.

           

          Configuring a Detailed Configuration for a MAG

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    vrf definition vrf-name

            4.    exit

            5.    ipv6 mobile pmipv6-mag mag-id domain domain-name

            6.    role {3gpp | wlan}

            7.    apn apn-name

            8.    local-routing-mag

            9.    discover-mn-detach poll interval seconds timeout seconds retries retry-count

            10.    address ipv4 ipv4-address

            11.    address ipv6 ipv6-address

            12.    sessionmgr

            13.    interface type number

            14.    binding maximum number

            15.    binding lifetime seconds

            16.    binding refresh-time seconds

            17.    binding init-retx-time milliseconds

            18.    binding max-retx-time milliseconds

            19.    replay-protection timestamp [window seconds]

            20.    bri delay min milliseconds

            21.    bri delay max milliseconds

            22.    bri retry number

            23.    lma lma-id domain-name

            24.    auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii | hex} hex-string

            25.    ipv4-address ipv4-address

            26.    vrfid vrf-name

            27.    encap {gre-ipv4 | ipv6-in-ipv6}

            28.    end

            29.    show ipv6 mobile pmipv6 mag mag-id globals


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.
             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 vrf definition vrf-name


            Example:
            Device(config)# vrf definition vrf1
             

            Configures a virtual routing and forwarding (VRF) routing table instance and enters VRF configuration mode.

             
            Step 4 exit


            Example:
            Device(config-vrf) exit
             

            Exits VRF configuration mode and returns to global configuration mode.

             
            Step 5 ipv6 mobile pmipv6-mag mag-id domain domain-name


            Example:
            Device(config)# ipv6 mobile pmipv6-mag mag1 domain dn1
             

            Enables the MAG service on a device, configures the PMIPv6 domain for the MAG, and enters MAG configuration mode.

             
            Step 6 role {3gpp | wlan}


            Example:
            Device(config-ipv6-pmipv6-mag)# role 3gpp
             

            Configures a role for the MAG.

            The keywords are as follows:

            • 3gpp—Specifies the role as 3GPP.
            • lte—Specifies the role as LTE.
            • wimax—Specifies the role as wimax.
            • wlan—Specifies the role as wireless LAN (WLAN).
             
            Step 7 apn apn-name


            Example:
            Device(config-ipv6-pmipv6-mag)# apn apn2
             

            Specifies an access point name (APN) to the subscriber of the MAG.

             
            Step 8 local-routing-mag


            Example:
            Device(config-ipv6-pmipv6-mag)# local-routing-mag
             

            Enables local routing for the MAG.

             
            Step 9 discover-mn-detach poll interval seconds timeout seconds retries retry-count


            Example:
            Device(config-ipv6-pmipv6-mag)# discover-mn-detach poll interval 11 timeout 3 retries 4
             

            Enables periodic verification of the MN attachment with the MAG-enabled interface.

             
            Step 10 address ipv4 ipv4-address


            Example:
            Device(config-ipv6-pmipv6-mag)# address ipv4 10.1.3.1
             

            Configures an IPv4 address for the MAG.

             
            Step 11 address ipv6 ipv6-address


            Example:
            Device(config-ipv6-pmipv6-mag)# address ipv6 2001:0DB8:2:4::1
             

            Configures an IPv6 address for the MAG.

             
            Step 12 sessionmgr


            Example:
            Device(config-ipv6-pmipv6-mag)# sessionmgr
             

            Configures an IPv6 address for the MAG.

             
            Step 13 interface type number


            Example:
            Device(config-ipv6-pmipv6-mag)# interface gigabitethernet 0/0/0
             

            Enables an interface for the MAG.

             
            Step 14 binding maximum number


            Example:
            Device(config-ipv6-pmipv6-mag)# binding maximum 200
             

            Specifies the maximum number of Proxy Binding Update (PBU) entries allowed for the MAG.

             
            Step 15 binding lifetime seconds


            Example:
            Device(config-ipv6-pmipv6-mag)# binding lifetime 5000
             

            Specifies the maximum lifetime permitted for the PBU entry.

             
            Step 16 binding refresh-time seconds


            Example:
            Device(config-ipv6-pmipv6-mag)# binding refresh-time 2000
             

            Specifies the PBU entry refresh time.

             
            Step 17 binding init-retx-time milliseconds


            Example:
            Device(config-ipv6-pmipv6-mag)# binding init-retx-time 110
             

            Specifies the initial timeout interval between the PBU and Proxy Binding Acknowledgment (PBA) until a PBA is received.

             
            Step 18 binding max-retx-time milliseconds


            Example:
            Device(config-ipv6-pmipv6-mag)# binding max-retx-time 4000
             

            Specifies the maximum timeout interval between the PBU and the PBA until a PBA is received.

             
            Step 19 replay-protection timestamp [window seconds]


            Example:
            Device(config-ipv6-pmipv6-mag)# replay-protection timestamp window 200
             

            Configures the replay protection mechanism within the PMIPv6 domain.

             
            Step 20 bri delay min milliseconds


            Example:
            Device(config-ipv6-pmipv6-mag)# bri delay min 500
             

            Specifies the minimum time for which an LMA should wait before transmitting the Binding Revocation Indication (BRI) message.

             
            Step 21 bri delay max milliseconds


            Example:
            Device(config-ipv6-pmipv6-mag)# bri delay max 4500
             

            Specifies the maximum time for which an LMA should wait for the Binding Revocation Acknowledgment (BRA) message before retransmitting the BRI message.

             
            Step 22 bri retry number


            Example:
            Device(config-ipv6-pmipv6-mag)# bri retry 6
             

            Specifies the maximum number of times an LMA should retransmit a BRI message, until a BRA is received.

             
            Step 23 lma lma-id domain-name


            Example:
            Device(config-ipv6-pmipv6-mag)# lma lma3 dn1
             

            Configures the LMA for the MAG and enters MAG-LMA configuration mode.

             
            Step 24 auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii | hex} hex-string


            Example:
            Device(config-ipv6-pmipv6mag-lma)# auth-option spi decimal 258 key hex BDF
             

            Configures authentication for the LMA within the MAG.

             
            Step 25 ipv4-address ipv4-address


            Example:
            Device(config-ipv6-pmipv6mag-lma)# ipv4-address 172.16.0.1
             

            Configures an IPv4 address for the LMA within the MAG.

             
            Step 26 vrfid vrf-name


            Example:
            Device(config-ipv6-pmipv6mag-lma)# vrfid vrf1
             

            Specifies a VRF for an LMA peer.

             
            Step 27 encap {gre-ipv4 | ipv6-in-ipv6}


            Example:
            Device(config-ipv6-pmipv6mag-lma)# encap gre-ipv4
             

            Configures a tunnel encapsulation mode type between the MAG and the LMA.

             
            Step 28 end


            Example:
            Device(config-ipv6-pmipv6mag-lma)# end
             

            Exits MAG-LMA configuration mode and returns to privileged EXEC mode.

             
            Step 29 show ipv6 mobile pmipv6 mag mag-id globals


            Example:
            Device# show ipv6 mobile pmipv6 mag mag1 globals
             

            (Optional) Displays MAG global configuration details.

             

            Example

            The following example shows the MAG global configuration:

            Router# show ipv6 mobile pmipv6 mag mag1 globals
             
            ---------------------------------------------------
            Domain  : D1
            Mag Identifier  : M1
                    MN's detach discover            : disabled
                    Local routing                   : disabled
                    Mag is enabled on interface     : GigabitEthernet0/0/0
                    Mag is enabled on interface     : GigabitEthernet0/1/0
                    Max Bindings                    : 3
                    AuthOption                      : disabled
                    RegistrationLifeTime            : 3600 (sec)
                    BRI InitDelayTime               : 1000 (msec)
                    BRI MaxDelayTime                : 40000 (msec)
                    BRI MaxRetries                  : 6
                    BRI EncapType                   : IPV6_IN_IPV6
                    Fixed Link address is           : enabled
                    Fixed Link address              : aaaa.aaaa.aaaa
                    Fixed Link Local address is     : enabled
                    Fixed Link local address        : 0xFE800000 0x0 0x0 0x2
                    RefreshTime                     : 300 (sec)
                    Refresh RetxInit time           : 20000 (msec)
                    Refresh RetxMax time            : 50000 (msec)
                    Timestamp option                : enabled
                    Validity Window                 : 7
                      
            Peer :  LMA1
                    Max Bindings                    : 3
                    AuthOption                      : disabled
                    RegistrationLifeTime            : 3600 (sec)
                    BRI InitDelayTime               : 1000 (msec)
                    BRI MaxDelayTime                : 40000 (msec)
                    BRI MaxRetries                  : 6
                    BRI EncapType                   : IPV6_IN_IPV6
                    Fixed Link address is           : enabled
                    Fixed Link address              : aaaa.aaaa.aaaa
                    Fixed Link Local address is     : enabled
                    Fixed Link local address        : 0xFE800000 0x0 0x0 0x2
                    RefreshTime                     : 300 (sec)
                    Refresh RetxInit time           : 20000 (msec)
                    Refresh RetxMax time            : 50000 (msec)
                    Timestamp option                : enabled
                    Validity Window                 : 7
            Peer :  LMA2
                    Max Bindings                    : 3
                    AuthOption                      : disabled

            Troubleshooting Tips

            You can use the following commands to troubleshoot the MAG configuration:

            • debug ipv6 mobile mag event
            • debug ipv6 mobile mag info
            • show ipv6 mobile pmipv6 mag bindings
            • show ipv6 mobile pmipv6 mag globals

            Configuration Examples for Proxy Mobile IPv6 Support for MAG Functionality

            Example: Configuring a Proxy Mobile IPv6 Domain by Using the Configuration from the AAA Server

            The following example shows how to configure the PMIPv6 domain by using the AAA server configuration:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D1 load-aaa
            

            The following example shows how to configure the PMIPv6 domain by using the configuration from the AAA server and how to override the configuration for specific PMIPv6 domain parameters:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D11 load-aaa
            Device(config)# ipv6 mobile pmipv6-domain D11
            Device(config-ipv6-pmipv6-domain)# gre-ipv4
            Device(config-ipv6-pmipv6-domain)# auth-option spi 67 key ascii key1
            

            Example: Configuring a Proxy Mobile IPv6 Domain When the Configuration from an AAA Server Is Not Available

            The following example shows how to configure the PMIPv6 domain when an AAA server configuration is not available:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D2
            Device(config-ipv6-pmipv6-domain)# replay-protection timestamp window 200
            Device(config-ipv6-pmipv6-domain)# auth-option spi 100 key ascii hi
            Device(config-ipv6-pmipv6-domain)# encap ipv6-in-ipv6
            !
            Device(config-ipv6-pmipv6-domain)# lma lma1
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.1.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:3::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            !
            Device(config-ipv6-pmipv6-domain)# mag mag1
            Device(config-ipv6-pmipv6-domain-mag)# ipv4-address 10.1.3.1
            Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:0DB8:2:5::1
            Device(config-ipv6-pmipv6-domain-mag)# exit
            !
            Device(config-ipv6-pmipv6-domain)# nai example1@example.com
            Device(config-ipv6-pmipv6-domain-mn)# lma lma1
            Device(config-ipv6-pmipv6-domain-mn)# int att gigabitethernet l2-addr 02c7.f800.0422
            Device(config-ipv6-pmipv6-domain-mn)# gre-encap-key up 1234
            Device(config-ipv6-pmipv6-domain-mn)# gre-encap-key down 5678
            Device(config-ipv6-pmipv6-domain-mn)# service ipv4
            Device(config-ipv6-pmipv6-domain-mn)# end
            

            Example: Configuring a Mobile Access Gateway

            The following example shows the minimum configuration required to enable MAG:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D2
            Device(config-ipv6-pmipv6-domain)# lma lma1
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.1.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:3::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            Device(config-ipv6-pmipv6-domain)# lma lma2
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.2.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:4::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            Device(config-ipv6-pmipv6-domain)# nai example1@example.com
            Device(config-ipv6-pmipv6-domain-mn)# lma lma1
            Device(config-ipv6-pmipv6-domain-mn)# exit
            Device(config-ipv6-pmipv6-domain)# nai example2@example.com
            Device(config-ipv6-pmipv6-domain-mn)# lma lma2
            Device(config-ipv6-pmipv6-domain-mn)# exit
            Device(config)# ipv6 mobile pmipv6-mag mag1 domain D2
            Device(config-ipv6-pmipv6-mag)# address ipv6 2001:DB8:0:0:E000::F
            Device(config-ipv6-pmipv6-mag)# address ipv4 10.2.1.1
            Device(ipv6-mag-config)# interface gigabitethernet 0/0/0
            Device(ipv6-mag-config)# role 3gpp
            Device(ipv6-mag-config)# apn a
            Device(ipv6-mag-config)# exit

            Where to Go Next

            The MAG entity works with the LMA provided by the ASR 5000 devices. To configure the LMA in the Cisco ASR 5000, see the “PDN Gateway Configuration” module in the Cisco ASR 5000 Series Packet Data Network Gateway Administration Guide.

            Additional References

            Related Documents

            Related Topic

            Document Title

            Cisco IOS commands

            Master Command List, All Releases

            IP mobility commands

            IP Mobility Command Reference

            Standards and RFCs

            Standard/RFC

            Title

            RFC 3775

            Mobility Support in IPv6

            RFC 5213

            Proxy Mobile IPv6

            RFC 5844

            IPv4 Support for Proxy Mobile IPv6

            RFC 5845

            Generic Routing Encapsulation (GRE) Key Option for Proxy Mobile IPv6

            RFC 5846

            Binding Revocation for IPv6 Mobility

            MIBs

            MIB

            MIBs Link

            None

            To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

            http:/​/​www.cisco.com/​go/​mibs

            Technical Assistance

            Description

            Link

            The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

            http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

            Feature Information for Proxy Mobile IPv6 Support for MAG Functionality

            The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

            Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

            Table 1 Feature Information for Proxy Mobile IPv6 MAG Functionality Support

            Feature Name

            Releases

            Feature Information

            Proxy Mobile IPv6 MAG Functionality Support

            Cisco IOS XE Release 3.4S

            The Proxy Mobile IPv6 Support for MAG Functionality feature provides network-based IP Mobility management to a mobile node without requiring the participation of the mobile node in any IP mobility-related signaling. The Mobile Access Gateway tracks the movements of the mobile node to and from the access link, and sends signals to the local mobility anchor of the mobile node.

            In Cisco IOS XE Release 3.4S, this feature was introduced on the Cisco ASR Series Aggregation Services 1000 routers.

            The following commands were introduced: address, apn, auth-option, binding, bri, clear ipv6 mobile pmipv6 mag, debug ipv6 mobile mag, debug ipv6 mobile packets, discover-mn-detach, encap, fixed-link-layer-address, fixed-link-local-address, gre-encap-key, int att, interface, ipv4-address, ipv6 mobile pmipv6-domain, ipv6 mobile pmipv6-mag, ipv6-address, lma, local-routing-mag, mag, mn-profile-load-aaa, multi-homed, nai, replay-protection, role, service, show ipv6 mobile pmipv6 mag binding, show ipv6 mobile pmipv6 mag globals, show ipv6 mobile pmipv6 mag stats.

            IPv6 Client Support on Proxy Mobile IPv6 Mobile Access Gateway

            Cisco IOS XE Release 3.5S

            Prior to the introduction of the IPv6 Client Support on Proxy Mobile IPv6 Mobile Access Gateway feature, only IPv4 service could be provided to an MN within the PMIP domain. The IPv6 client support on Proxy Mobile IPv6 MAG feature is an enhancement to provide IPv4, IPv6, and dual service to the MN within the PMIP domain.

            The following command was modified: service.