IP Routing: ISIS Configuration Guide, Cisco IOS XE Release 3S (Cisco ASR 1000)
Reducing Failure Detection Times in IS-IS Networks
Downloads: This chapterpdf (PDF - 163.0KB) The complete bookPDF (PDF - 1.63MB) | Feedback

Reducing Failure Detection Times in IS-IS Networks

Reducing Failure Detection Times in IS-IS Networks

Last Updated: December 4, 2012

This module describes how to customize IS-IS configuration to help you achieve fast convergence in your network. This module describes how to configure Bidirectional Failure Detection (BFD) and how to perform other tasks to optimize how a router that runs IS-IS detects link failures and topology changes, sends important topology change updates to its neighbors, and reacts to the topology change updates that it receives from its neighbors, in order to increase network performance.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for Reducing Failure Detection Times in IS-IS Networks

Before performing the tasks in this module, you should be familiar with the concepts described in the "Overview of IS-IS Fast Convergence" module.

Information About Reducing Failure Detection Times in IS-IS Networks

You can customize your IS-IS network to reduce the amount of time it takes for network failures to be discovered. When failures are detected more quickly, networks can react to them sooner and alternate paths can be selected more quickly, speeding up network convergence.

You can enable BFD support for routing protocols at the router level to enable BFD support globally for all interfaces or you can configure BFD on a per-interface basis at the interface level.

For Cisco IOS XE Release 2.1 and later releases, you must configure BFD support for one or more of the following routing protocols: BGP, IS-IS, and OSPF.

IS-IS is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD. There are two methods for enabling BFD support for IS-IS:

  • You can enable BFD for all of the interfaces for which IS-IS is routing by using the bfd all-interfaces command in router configuration mode. You can then disable BFD for one or more of those interfaces using the isis bfd disable command in interface configuration mode.
  • You can enable BFD for a subset of the interfaces for which IS-IS is routing by using the isis bfd command in interface configuration mode.

IP event dampening introduces a configurable exponential delay mechanism to suppress the effects of excessive interface flapping events on routing protocols and routing tables in the network. This feature allows the network operator to configure a router to automatically identify and selectively dampen a local interface that is flapping, removing it from the network until it becomes stable again. Thus, the network becomes more stable, with a faster convergence time.

BFD is a detection protocol designed to provide fast forwarding path failure detection times for all media types, encapsulations, topologies, and routing protocols. In addition to fast forwarding path failure detection, BFD provides a consistent failure detection method for network administrators. Because the network administrator can use BFD to detect forwarding path failures at a uniform rate, rather than the variable rates for different routing protocol hello mechanisms, network profiling and planning will be easier, and reconvergence time will be consistent and predictable.

For complete information about the BFD feature, see the following documentation:

  • "Bidirectional Forwarding Detection"

Tuning hello parameters should be considered only when the link type does not offer fast enough link failure detection. The standard default values for the hello interval and hello multiplier are 10 seconds and 3 seconds. Therefore, the multiplier times the interval will give a default hold-time of 30 seconds.

Configuring a point-to-point adjacency over a broadcast media can improve convergence times of a customer's network because it prevents the system from electing a designated router (DR), prevents flooding from using CSNPs for database synchronization, and simplifies shortest path first (SPF) computations.

How to Reduce Failure Detection Times in IS-IS Networks

Using Bidirectional Forwarding Failure Detection to Decrease Failure Detection Times

Configuring BFD Session Parameters on the Interface

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number

4.    bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier

5.    end


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
interface type number


Example:

Router(config)# interface GigabitEthernet 6/0/0

 

Enters interface configuration mode.

 
Step 4
bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier


Example:

Router(config-if)# bfd interval 50 min_rx 50 multiplier 5

 

Enables BFD on the interface.

 
Step 5
end


Example:

Router(config-if)# end

 

Exits interface configuration mode.

 

Configuring BFD Support for IS-IS

Prerequisites
  • IS-IS must be running on all participating routers.
  • The baseline parameters for BFD sessions on the interfaces that you want to run BFD sessions to BFD neighbors over must be configured. See the Configuring BFD Session Parameters on the Interface for more information.
Configuring BFD Support for IS-IS for All Interfaces
SUMMARY STEPS

1.    enable

2.    configure terminal

3.    router isis area-tag

4.    bfd all-interfaces

5.    exit

6.    interface type number

7.    isis bfd [disable]

8.    end

9.    show bfd neighbors [details]


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
router isis area-tag


Example:

Router(config)# router isis tag1

 

Specifies an IS-IS process and enters router configuration mode.

 
Step 4
bfd all-interfaces


Example:

Router(config-router)# bfd all-interfaces

 

Enables BFD globally on all interfaces associated with the IS-IS routing process.

 
Step 5
exit


Example:

Router(config-router)# exit

 

(Optional) Returns the router to global configuration mode. Enter this command only if you want to follow Step 6 and Step 7 to disable BFD for one or more interfaces.

 
Step 6
interface type number


Example:

Router(config)# interface gigabitethernet 6/0/0

 

(Optional) Enters interface configuration mode.

 
Step 7
isis bfd [disable]


Example:

Router(config-if)# isis bfd

 

Enables or disables BFD on a per-interface basis for one or more interfaces associated with the IS-IS routing process.

Note    You should use the disable keyword only if you enabled BFD on all of the interfaces that IS-IS is associated with using the bfd all-interfaces command in router configuration mode.
 
Step 8
end


Example:

Router(config-if)# end

 

Returns the router to privileged EXEC mode.

 
Step 9
show bfd neighbors [details]


Example:

Router# show bfd neighbors details

 

Displays information that can be used to verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

 
Configuring BFD Support for IS-IS for One or More Interfaces
SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number

4.    isis bfd [disable]

5.    end

6.    show bfd neighbors [details]


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
interface type number


Example:

Router(config)# interface gigabitethernet 6/0/0

 

Enters interface configuration mode.

 
Step 4
isis bfd [disable]


Example:

Router(config-if)# isis bfd

 

Enables or disables BFD on a per-interface basis for one or more interfaces associated with the IS-IS routing process.

Note    You should use the disable keyword only if you enabled BFD on all of the interfaces that IS-IS is associated with using the bfd all-interfaces command in router configuration mode.
 
Step 5
end


Example:

Router(config-if)# end

 

Returns the router to privileged EXEC mode.

 
Step 6
show bfd neighbors [details]


Example:

Router# show bfd neighbors details

 

Displays information that can help verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

 

Using IP Event Dampening to Decrease Failure Detection Times

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number

4.    dampening [half-life-period reuse-threshold] [suppress-threshold max-suppress-time [restart-penalty]]

5.    end

6.    show dampening interface

7.    show interface dampening


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
interface type number


Example:

Router(config)# interface GigabitEthernet 0/1/0

 

Enters interface configuration mode.

 
Step 4
dampening [half-life-period reuse-threshold] [suppress-threshold max-suppress-time [restart-penalty]]


Example:

Router(config-if)# dampening

 

Enables interface dampening.

  • Entering the dampening command without any keywords or arguments enables interface dampening with the default configuration parameters.
Note    The default values for the half-life-period, reuse-threshold, suppress-threshold, max-suppress-time, and restart-penalty arguments are 5, 1000, 2000, 20, and 2000, respectively.
  • When the timer for the restart-penalty argument is manually configured, the values must be manually entered for all arguments.
 
Step 5
end


Example:

Router(config-if)# end

 

Exits interface configuration mode and returns to privileged EXEC mode.

 
Step 6
show dampening interface


Example:

Router# show dampening interface

 

Displays a summary of dampened interfaces.

 
Step 7
show interface dampening


Example:

Router# show interface dampening

 

Displays dampened interfaces on the local router.

 

Tuning IS-IS Hello Parameters to Decrease Link Failure Detection Times

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number

4.    isis hello-interval {seconds | minimal} [level-1 | level-2]

5.    isis hello-multiplier multiplier [level-1 | level-2]

6.    end


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables higher privilege levels, such as privileged EXEC mode.

Enter your password if prompted.

 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
interface type number


Example:

Router(config)# interface GigabitEthernet 0/1/0

 

Configures an interface type and enters interface configuration mode.

 
Step 4
isis hello-interval {seconds | minimal} [level-1 | level-2]


Example:

Router(config-if)# isis hello-interval 5 level-1

 

Specifies the length of time between the sending of IS-IS hello PDUs.

  • The default value is 10. The hello interval multiplied by the hello multiplier equals the hold time. If the minimal keyword is specified, the hold time is 1 second and the system computes the hello interval based on the hello multiplier.
  • The hello interval can be configured independently for Level 1 and Level 2, except on serial point-to-point interfaces. (Because only a single type of hello PDU is sent on serial links, it is independent of Level 1 or Level 2.) The level-1 and level-2 keywords are used on SMDS and Frame Relay multiaccess networks or LAN interfaces.
Note    A faster hello interval gives faster convergence, but increases bandwidth and CPU usage. It might also add to instability in the network, due to false failure detection events. A slower hello interval saves bandwidth and CPU. Especially when used in combination with a higher hello multiplier, this configuration may increase overall network stability, but has typical slower network convergence as a consequence.
 
Step 5
isis hello-multiplier multiplier [level-1 | level-2]


Example:

Router(config-if)# isis hello-multiplier 6 level-1

 

Specifies the number of IS-IS hello PDUs a neighbor must miss before the router should declare the adjacency as down.

  • The default value is 3. A multiplier value of 1 is very aggressive--we recommend a value of at least 2.
 
Step 6
end


Example:

Router(config-if)# end

 

Returns to privileged EXEC mode.

 

Configuring an IS-IS Point-to-Point Adjacency over Broadcast Media to Reduce Link Failure Detection Times


Note


We recommend that you perform this task only for IS-IS networks that consist of only two networking devices connected to broadcast media. Such networks are usually configured as a point-to-point link rather than a broadcast link. In this case, it is recommended to follow this task to decrease the link failure detection time.

Having a multipoint interface instead of the point-to-point interfaces will cause the creation of a pseudonode on the network. The addition of the pseudonode means that the router must retain information about it. To decrease the size of the topology database of the router, thereby reducing the memory requirement of the router and increasing the efficiency of the SPF calculation since there is one less node involved, configure point-to-point interfaces when possible.

>
SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface interface-type interface-number

4.    isis network point-to-point

5.    end


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables higher privilege levels, such as privileged EXEC mode.

Enter your password if prompted.

 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
interface interface-type interface-number


Example:

Router(config)# interface gigabitethernet 4/0/0

 

Configures an interface type and enters interface configuration mode.

 
Step 4
isis network point-to-point


Example:

Router(config-if)# isis network point-to-point

 

Configures a network of only two networking devices that use broadcast media and the integrated IS-IS routing protocol to function as a point-to-point link instead of a broadcast link.

 
Step 5
end


Example:

Router(config-if)# end

 

Returns to privileged EXEC mode.

 

Monitoring IS-IS Network Convergence Time

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    isis display delimiter [return count | character count]

4.    exit

5.    show isis database [level-1] [level-2] [l1] [l2] [detail] [lspid]

6.    show isis [area-tag] routes

7.    show isis spf-log

8.    show isis [process-tag] topology


DETAILED STEPS
  Command or Action Purpose
Step 1
enable


Example:

Router> enable

 

Enables privileged EXEC mode.

  • Enter your password if prompted.
 
Step 2
configure terminal


Example:

Router# configure terminal

 

Enters global configuration mode.

 
Step 3
isis display delimiter [return count | character count]


Example:

Router(config)# isis display delimiter return 2

 

Makes output from multiarea displays easier to read by specifying the delimiter to use to separate displays of information.

 
Step 4
exit


Example:

Router(config)# exit

 

Returns to privileged EXEC mode.

 
Step 5
show isis database [level-1] [level-2] [l1] [l2] [detail] [lspid]


Example:

Router# show isis database detail

 

Displays the IS-IS link-state database.

 
Step 6
show isis [area-tag] routes


Example:

Router# show isis financetag routes

 

Displays the IS-IS Level 1 forwarding table for IS-IS learned routes.

 
Step 7
show isis spf-log


Example:

Router# show isis spf-log

 

Displays how often and why the router has run a full SPF calculation.

 
Step 8
show isis [process-tag] topology


Example:

Router# show isis financetag topology

 

Displays a list of all connected routers in all areas.

  • If a process tag is specified, output is limited to the specified routing process. When "null" is specified for the process tag, output is displayed only for the router process that has no tag specified. If a process tag is not specified, output is displayed for all processes.
 

Configuration Examples for Reducing Failure Detection Times in IS-IS Networks

Example Configuring IS-IS to Achieve Fast Convergence by Reducing Failure Detection Times

The following example configures Gigabit Ethernet interface 0/0/0 to use IP event dampening, setting the half life to 30 seconds, the reuse threshold to 1500, the suppress threshold to 10,000, and the maximum suppress time to 120 seconds. The IS-IS hello parameters have also been tuned for more rapid failure detection

enable
configure terminal
interface GigabitEthernet 0/0/0
 dampening 30 1500 10000 120
 isis hello-interval minimal
 isis hello-multiplier 2

Where to Go Next

To configure additional features to improve IS-IS network convergence times, complete the optional tasks in one or more of the following modules:

  • "Setting Best Practice Parameters for IS-IS Fast Convergence"
  • "Reducing Alternate-Path Calculation Times in IS-IS Networks"

Additional References

The following sections provide references related to reducing failure detection times in IS-IS networks.

Related Documents

Related Topic

Document Title

IS-IS commands: complete command syntax, command mode, defaults, command history, usage guidelines, and examples

Cisco IOS IP Routing: ISIS Command Reference

Overview of Cisco IS-IS conceptual information with links to all the individual IS-IS modules

"Overview of IS-IS Fast Convergence"

Cisco IOS master command list, all releases

Cisco IOS Master Command List, All Releases

Standards

Standard

Title

No new or modified standards are supported, and support for existing standards has not been modified.

--

MIBs

MIB

MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFC

Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

--

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport

Feature Information for Reducing Failure Detection Times in IS-IS Networks

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Table 1 Feature Information for Reducing Failure Detection Times in IS-IS Networks

Feature Name

Software Releases

Feature Information

Integrated IS-IS Point-to-Point Adjacency over Broadcast Media

Cisco IOS XE Release 2.1

When a network consists of only two networking devices connected to broadcast media and uses the integrated IS-IS protocol, it is better for the system to handle the link as a point-to-point link instead of as a broadcast link. This feature introduces a new command to make IS-IS behave as a point-to-point link between the networking devices.

In Cisco IOS XE Release 2.1 this feature was introduced on the Cisco ASR 1000 Series Routers.

The following commands were modified by this feature: isis network point-to-point.

IS-IS Support for BFD over IPv4

Cisco IOS XE Release 2.1

BFD is a detection protocol designed to provide fast forwarding path failure detection times for all media types, encapsulations, topologies, and routing protocols. In addition to fast forwarding path failure detection, BFD provides a consistent failure detection method for network administrators. Because the network administrator can use BFD to detect forwarding path failures at a uniform rate, rather than the variable rates for different routing protocol hello mechanisms, network profiling and planning will be easier, and reconvergence time will be consistent and predictable.

This feature was introduced on the Cisco ASR 1000 Series Aggregation Services Routers.

The following commands were modified by this feature: bfd all-interfaces, bfd interval, isis bfd, router isis, show bfd neighbors.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.