Step 1 |
enable
Example:
|
Enables privileged EXEC mode. Enter your password when prompted.
|
Step 2 |
configure
terminal
Example:
Router# configure terminal
|
Enters global configuration mode.
|
Step 3 |
network-clock-participate
slot
number
Example:
Router(config)# network-clock-participate slot 1
|
Enables the network module in the specified slot to use the network clock for its timing.
|
Step 4 |
network-clock-participate
slot
number
Example:
Router(config)# network-clock-participate slot 4
|
Enables the network module in the specified slot to use the network clock for its timing.
|
Step 5 |
network-clock-participate
aim
number
Example:
Router(config)# network-clock-participate aim 0
|
Specifies that the AIM in Slot 0 will derive clocking from the network source.
|
Step 6 |
voice
service
{pots
|
voatm
|
vofr
|
voip}
Example:
Router(config)# voice service voatm
|
Enters voice service configuration mode and specifies VoATM as the encapsulation type.
|
Step 7 |
session
protocol
aal2
Example:
Router(config-voi-serv)# session protocol aal2
|
Enters voice-service-session configuration mode and specifies ATM adaptation layer 2 (AAL2) trunking.
|
Step 8 |
subcell-mux
Example:
Router(conf-voi-serv-sess)# subcell-mux
|
Enables AAL2 common part sublayer (CPS) subcell multiplexing.
|
Step 9 |
codec
aal2-profile
custom
profile-number
codec
Example:
Router# codec aal2-profile custom 51 0 0 llcc 40 0 15
|
Sets the codec profile for the DSP on a per-call basis and specifies the lossless compression codec.
|
Step 10 |
controller
t1
|
e1
slot/port
Example:
Router(config)# controller e1 1/0
|
Enters controller configuration mode for the selected T1 or E1.
|
Step 11 |
mode
atm
aim
aim-slot
Example:
Router(config-controller)# mode atm aim 0
|
Sets the mode of the T1 or E1 controller in AIM Slot 0.
|
Step 12 |
controller
t1
|
e1
slot/port
Example:
Router(config)# controller e1 4/0
|
Enters controller configuration mode for the selected T1 or E1.
|
Step 13 |
ds0-group
ds0-group-number
timeslots
timeslot-list
type
signaling
method
Example:
Router(config-controller)# ds0-group 0 timeslots 1 type ext-sig
|
Specifies the DS0 time slots that make up a logical voice port on a T1 or E1 controller and specifies the signaling type used by the router.
|
Step 14 |
interface
atm
interface-number
/subinterface-number
Example:
Router(config) # interface atm 1/0
|
Enters configuration mode for the selected ATM interface.
|
Step 15 |
pvc
vpi
/vci
Example:
Router(config-if-atm)# pvc 10/110
|
Enters configuration mode for the selected PVC.
|
Step 16 |
vbr-rt
peak-rate
average-rate
burst
Example:
Router(config-if-atm-pvc)# vbr-rt 1920 1920 255
|
Configures real-time variable bit rate (VBR) for VoATM voice connections.
|
Step 17 |
encapsulation
aal2
Example:
Router(config-if-atm-pvc)# encapsulation aal2
|
Configures the encapsulation type for the ATM virtual circuit.
|
Step 18 |
dial-peer
voice
tag
voatm
Example:
Router(config)# dial-peer voice 1001 voatm
|
Defines a dial-peer and specifies the method of voice encapsulation as VoATM.
|
Step 19 |
destination-pattern
string
Example:
Router(config-dial-peer)# destination-pattern 1001
|
Specifies the prefix to be used by the dial peer.
|
Step 20 |
session
protocol
aal2-trunk
Example:
Router(config-dial-peer)# session protocol aal2-trunk
|
Specifies the dial peer uses AAL2 nonswitched trunk session protocol.
|
Step 21 |
session
target
interface
pvc
vpi/vci
Example:
Router(config-dial-peer)# session target atm 1/0 pvc 10/100 9
|
Specifies the network-specific address for the VoATM dial peer.
|
Step 22 |
signal-type
cas
|
cept
|
ext-signal
|
transparent
Example:
Router(config-dial-peer)# signal-type ext-signal
|
Specifies that external signaling is used when connecting to the dial peer. The DSP does not generate any signaling frames.
|
Step 23 |
codec
aal2-profile
custom
profile-number
codec
Example:
Router(config-dial-peer)# codec aal2-profile custom 51 llcc
|
Sets the codec profile for the DSP on a per-call basis and specifies the lossless compression codec.
|
Step 24 |
voice-port
{slot-number/subunit-number/port | slot/port:ds0-group-no}
Example:
Router(config)# voice-port 2/0:0
|
Enters voice-port configuration mode.
|
Step 25 |
playout-delay
{fax
|
maximum
|
nominal}
milliseconds
Example:
Router(config-voice-port)# playout-delay nominal 25
|
Tunes the playout buffer to accommodate packet jitter caused by switches in the WAN. The nominal keyword specifies the initial (and minimum allowed) delay time that the DSP inserts before playing out voice packets, in milliseconds.
|
Step 26 |
connection
{plar
|
tie-line
|
plar-opx}
digits
|
{trunk
digits
[answer-mode]}
Example:
Router(config-voice-port)# connection trunk 1001
|
Associates this voice-port to destination-pattern 1001.
|