Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
Overview: Cisco ASR 1000 Series Aggregation Services Routers SIPs
Downloads: This chapterpdf (PDF - 948.0KB) The complete bookPDF (PDF - 4.25MB) | Feedback

Table of Contents

Overview: Cisco ASR 1000 Series Aggregation Services Routers SIPs

SIP Summary

Checking Hardware and Software Compatibility

SPA Interface Addresses on SIPs

Identifying Slots and Subslots for SIPs and SPAs

Specifying the Slot Location for a SIP

Specifying the SIP Subslot Location for a SPA

Cisco ASR 1000 Series SPA Interface Processor Overview

Cisco ASR1000-SIP10 Overview

Cisco ASR1000-SIP10 LEDs

Cisco ASR1000-SIP10 Physical Specifications

Cisco ASR1000-SIP40 Overview

Cisco ASR1000-SIP40 LEDs

Cisco ASR1000-SIP40 Physical Specifications

Cisco ASR 1013 Router and Slot Numbering for SIP

Overview: Cisco ASR 1000 Series Aggregation Services Routers SIPs

This chapter describes the SPA interface processors (SIPs) that are supported on the Cisco ASR 1000 Series Aggregation Services Routers and contains the following sections:

SIP Summary

Summary descriptions of the SIPs that are supported on the Cisco ASR 1000 Series Routers are shown in Table 1-1 .


NoteThe Description column indicates the aggregate bandwidth supported by the SIP across all subslots, and not per SPA subslot. The Description column indicates the aggregate bandwidth supported by the SIP across all subslots, and not per SPA subslot.


 

Table 1-1 SIP Summary

SIP
Product Number
Description
Maximum Number of SPAs
Minimum Cisco IOS Release

Cisco ASR 1000 Series SIP10G

ASR-1000-SIP10

10 Gbps SPA interface processor

4

Cisco IOS XE Release 2.2

Cisco ASR 1000 Series SIP40G

ASR-1000-SIP40

40 Gbps SPA interface processor

41

Cisco IOS XE Release 3.1S

1.The Cisco ASR1000-SIP40 carrier card supports four half-height SPAs, two full-height SPAs, or a combination of two half-height and one full-height SPAs. Double-wide SPAs are not supported.

Checking Hardware and Software Compatibility

To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for individual hardware modules or components.


NoteAccess to this tool is limited to users with Cisco.com login accounts. Access to this tool is limited to users with Cisco.com login accounts.


To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box, and click GO. Click the link for the Software Advisor tool.

Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware. For details regarding the hardware and software supported for ASR1000 SIPs, refer Table 1-2 .


NoteThe Cisco ASR 1002-X Router has an integrated route processor, embedded services processor, and SIP. The Cisco ASR 1002-X Router has an integrated route processor, embedded services processor, and SIP.


Table 1-2 Hardware and Software Support Matrix for ASR1000 SIPs

SIP Type
Cisco IOS XE Software Release
Supported Route Processor
Supported ESP
Supported Cisco ASR 1000 Router Chassis

ASR1000-SIP10

Cisco IOS XE Release 2

ASR1000-RP1 and ASR1000-RP2

ASR1000-ESP10, ASR1000-ESP10-N, ASR1000-ESP20, ASR1000-ESP40, and ASR1000-ESP100

Note ASR1000-ESP100 is supported only on routers on which ASR1000-RP2 is installed.

Cisco ASR1002, Cisco ASR 1002-F, Cisco ASR 1004, Cisco ASR 1006, and Cisco ASR 1013 Routers

ASR1000-SIP40

Cisco IOS XE Release 3.1S

ASR1000-RP2 and later RPs

ASR1000-ESP10, ASR1000-ESP10-N, ASR1000-ESP20, ASR1000-ESP40, and ASR1000-ESP100

ASR1000-ESP100 is supported only on routers on which ASR1000-RP2 is installed.

Cisco ASR 1002-X, Cisco ASR 1004, Cisco ASR 1006, and Cisco ASR 1013 Routers2

ASR1000-SIP40

Cisco IOS XE Release 3.2S3

ASR1000-RP2 and later RPs

Primarily supported only on ASR1000-ESP40

Cisco ASR 1004 Routers

2.The Cisco ASR 1013 Router has limitation to support ASR1000-SIP40 at slots 4 and 5 at 40G mode. If a ASR1000-SIP40 is installed at slots 4 or 5, it will work as a SIP10 at 10G mode.

3.Support for SIP-40 and ESP-40 added on Cisco ASR 1004 Router Chassis from Cisco IOS XE Release 3.2S and future releases.

SPA Interface Addresses on SIPs

Interface addresses specify the physical location of each interface on a router or switch. Table 1-3 describes how to identify the interface addresses for SPAs supported on the SIPs.

 

Table 1-3 SPA Interface Addresses

SIP
Address Format
Description

Cisco ASR 1000 Series SIP

router-module-slot/SIP-subslot/SPA-port-number

Router module slot—0 through 2

SIP subslot—0 through 3

SPA port number—0 through x

Note The maximum number of SPA ports depends on the type of SPA.

Identifying Slots and Subslots for SIPs and SPAs

This section describes how to specify the physical locations of a SIP and SPA on the Cisco ASR 1000 Series Routers within the command-line interface (CLI) to configure or monitor the devices.

Specifying the Slot Location for a SIP

The Cisco ASR 1000 Series Routers support different chassis models, each of which supports a certain number of chassis slots.

  • The Cisco ASR 1013 Router supports six chassis slots for SIPs.
  • The Cisco ASR 1006 Router supports three chassis slots for SIPs.
  • The Cisco ASR 1004 Router supports two chassis slots for SIPs.
  • The Cisco ASR 1002 Router and Cisco ASR 1002-X Router support one chassis slot for a SIP that is permanently installed, and the integrated Route Processor and Gigabit Ethernet ports reside in SPA subslot 0.

Figure 1-1 shows an example of a SIP installed on a Cisco ASR 1006 Router. The router has three chassis slots for SIPs, and can accommodate a total of twelve SPAs.

Figure 1-1 SIP and SPAs Installed in a Cisco ASR 1006 Router

 

Some commands allow you to display information about the SIP itself, such as show platform , show diag , and show diag subslot . These commands require you to specify the chassis slot location where the SIP that you want information about is installed.

For example, to display status and slot-related information about the SIP installed in any of the chassis slots, enter the following command:

Router# show platform
Chassis type: ASR1006
 
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 2d21h
0/0 SPA-2X1GE-V2 ok 2d21h
0/1 SPA-2X1GE-V2 ok 2d21h
0/2 SPA-2X1GE-V2 ok 2d21h
0/3 SPA-1XOC12-POS ok 2d21h
1 ASR1000-SIP10 ok 22:46:22
1/0 SPA-1X10GE-L-V2 ok 22:45:29
1/1 SPA-1XOC12-POS ok 22:45:26
1/2 SPA-1X10GE-L-V2 ok 22:45:22
1/3 SPA-1XOC12-POS ok 22:45:18
2 ASR1000-SIP10 ok 1d20h
2/0 SPA-5X1GE-V2 ok 1d20h
2/1 SPA-5X1GE-V2 ok 1d20h
2/2 SPA-5X1GE-V2 ok 1d20h
2/3 SPA-5X1GE-V2 ok 1d20h
R0 ASR1000-RP1 ok, active 3d20h
F0 ASR1000-ESP10 ok, active 3d20h
P0 ASR1006-PWR-AC ok 3d20h
P1 ASR1006-FAN ok 3d20h
 
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 07091401 12.2(33r)XN2
1 07091401 12.2(33r)XN2
2 07091401 12.2(33r)XN2
R0 07082312 12.2(33r)XN2
 

The following example shows the show platform command output for the ASR 1013 chassis with Cisco ASR1000-SIP10 and Cisco ASR1000-SIP40 installed:

Router# show platform
Chassis type: ASR1013
 
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 1w0d
1 ASR1000-SIP40 ok 1w0d
1/1 SPA-5X1GE-V2 ok 1w0d
2 ASR1000-SIP40 ok 1w0d
2/1 SPA-1X10GE-L-V2 ok 1w0d
2/3 SPA-1X10GE-L-V2 ok 1w0d
3 ASR1000-SIP40 ok 1w0d
3/3 SPA-4XT3/E3 ok 1w0d
4 ASR1000-SIP40 ok 1w0d
4/2 SPA-5X1GE-V2 ok 1w0d
4/3 SPA-4XCT3/DS0 ok 1w0d
5 ASR1000-SIP40 ok 1w0d
R0 ASR1000-RP2 ok, active 1w0d
R1 ASR1000-RP2 ok, standby 1w0d
F0 ASR1000-ESP40 ok, active 1w0d
P0 ASR1013-PWR-AC ok 1w0d
P1 ASR1013-PWR-AC ps, fail 1w0d
P2 ASR1013-PWR-AC ok 1w0d
P3 ASR1013-PWR-AC ps, fail 1w0d
 
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 00200800 15.0(1r)S
1 00200800 15.0(1r)S
2 00200800 15.0(1r)S
3 00200800 15.0(1r)S
4 00200800 15.0(1r)S
5 00200800 15.0(1r)S
R0 10021901 15.0(1r)S
R1 10021901 15.0(1r)S
F0 1001270D 15.0(1r)S

Specifying the SIP Subslot Location for a SPA

SIP subslots begin their numbering with “0” and have a horizontal orientation, as shown in the “SIP and SPA Product Overview” chapter of the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide .

The Cisco ASR 1000 series SIP supports four subslots for the installation of SPAs. As shown in Figure 1-2, the subslot locations are oriented as follows:

  • SIP subslot 0—Top-left subslot
  • SIP subslot 1—Top-right subslot
  • SIP subslot 2—Bottom-left subslot
  • SIP subslot 3—Bottom-right subslot

NoteOn the Cisco ASR 1002 Router and Cisco ASR 1002-X Router, SIP subslot 0 is not available for SPA insertion. It is the slot that is used for the integrated Route Processor and Gigabit Ethernet ports. On the Cisco ASR 1002 Router and Cisco ASR 1002-X Router, SIP subslot 0 is not available for SPA insertion. It is the slot that is used for the integrated Route Processor and Gigabit Ethernet ports.


Figure 1-2 shows the SPA numbering sequence on a Cisco ASR 1000 Series Routers SIP.

Figure 1-2 Cisco ASR 1000 Series SIP SPA Numbering

 

The SIP subslot numbering is indicated by a small numeric label beside the subslot on the faceplate.

Just as with the SIPs, some commands allow you to display information about the SPA itself, such as show diag subslot. These commands require you to specify both the physical location of the SIP and SPA in the format, slot / subslot , where:

  • slot —Specifies the chassis slot number in the Cisco ASR 1000 Series Routers where the SIP is installed.
  • subslot —Specifies the slot of the SIP where the SPA is installed.

To display the operational status for a SPA installed in the SIP, enter the show platform command.

Router# show platform
Chassis type: ASR1006
 
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 2d21h
0/0 SPA-2X1GE-V2 ok 2d21h
0/1 SPA-2X1GE-V2 ok 2d21h
0/2 SPA-2X1GE-V2 ok 2d21h
0/3 SPA-1XOC12-POS ok 2d21h
1 ASR1000-SIP10 ok 22:46:22
1/0 SPA-1X10GE-L-V2 ok 22:45:29
1/1 SPA-1XOC12-POS ok 22:45:26
1/2 SPA-1X10GE-L-V2 ok 22:45:22
1/3 SPA-1XOC12-POS ok 22:45:18
2 ASR1000-SIP10 ok 1d20h
2/0 SPA-5X1GE-V2 ok 1d20h
2/1 SPA-5X1GE-V2 ok 1d20h
2/2 SPA-5X1GE-V2 ok 1d20h
2/3 SPA-5X1GE-V2 ok 1d20h
R0 ASR1000-RP1 ok, active 3d20h
F0 ASR1000-ESP10 ok, active 3d20h
P0 ASR1006-PWR-AC ok 3d20h
P1 ASR1006-FAN ok 3d20h
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 07091401 12.2(33r)XN2
1 07091401 12.2(33r)XN2
2 07091401 12.2(33r)XN2
R0 07082312 12.2(33r)XN2
 

The following is a show platform command output example displaying the status of the DSP SPA installed on a Cisco ASR 1000 Series Routers:

Router# show platform
Chassis type: ASR1004
 
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 ASR1000-SIP10 ok 00:14:53
1/0 SPA-10X1GE-V2 ok 00:12:51
1/3 SPA-DSP ok 00:12:47
R0 ASR1000-RP1 ok, active 00:14:53
F0 ASR1000-ESP10 ok, active 00:14:53
P0 ASR1004-PWR-AC ps, fail 00:14:04
P1 ASR1004-PWR-AC ok 00:14:03
 
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 07091401 12.2(33r)XN2
R0 07062111 12.2(33r)XN2
F0 07051650 12.2(33r)XN2
 

Cisco ASR 1000 Series SPA Interface Processor Overview

This section provides an overview of the SPA Interface Processor (SIP) supported on the Cisco ASR 1000 Series Routers. This section contains the following topics:

Cisco ASR1000-SIP10 Overview

The following sections describe the Cisco ASR1000-SIP10:

Cisco ASR1000-SIP10 LEDs

The Cisco ASR1000-SIP10 has two LEDs, as shown in Figure 1-3.

Figure 1-3 Cisco ASR1000-SIP10 Faceplate

 

1

SPA, subslot 0

4

PWR LED

2

SPA, subslot 1

5

STATUS LED

3

SPA, subslot 2

6

SPA, subslot 3

The Cisco ASR1000-SIP10 LEDs are described in Table 1-4 .

 

Table 1-4 Cisco ASR1000-SIP10 LEDs

LED Label
Color
State
Meaning

STATUS

Red

On

The Cisco ASR1000-SIP10 has encountered an error.

 

Yellow

On

The Cisco ASR1000-SIP10 is loading.

 

Green

On

The Cisco ASR1000-SIP10 is online.

 

Off

Off

The Cisco ASR1000-SIP10 is powered off.

PWR

Green

On

The Cisco ASR1000-SIP10 is powered on.

 

Off

Off

The Cisco ASR1000-SIP10 is powered off.

Cisco ASR1000-SIP10 Physical Specifications

The Cisco ASR1000-SIP10 physical specifications are described in Table 1-5 .

 

Table 1-5 Cisco ASR1000-SIP10 Physical Specifications

Description
Specifications

Physical dimension (HxWxD)

1.630 inches (41.4 mm) x 16.725 inches (424.8 mm) x 14.187 inches (360.3 mm)

Shipping weight

8.5 lb (3.9 kg)

Operating temperature

Nominal—40.9°F to 104°F (5 to 40°C)
Short Term—40.9°F to 131°F (5 to 55°C)

Relative humidity

Operating Humidity Nominal—5% to 85% noncondensing
Operating Humidity Short Term—5% to 90% noncondensing

Storage temperature

–40°F to 158°F (–40°C to 70°C)

Cisco ASR1000-SIP40 Overview

The Cisco ASR1000-SIP40 supports up to 40 Gbps total bandwidth for the four SPA bays and 46 Gbps sustained through carrier card when utilizing two four-link 6.25GHz ESIs. Following are the features of the Cisco ASR1000-SIP40:

  • Supports 40 Gbps of non oversubscribed throughput.
  • Compatible with existing and future SPAs, ESPs, and RPs.
  • Supports online-insertion-and-removal (OIR) of all SIP-10 SPAs and Cisco ASR1000-SIP40.
  • Provides higher port density support of 48 point dual priority, and 96 point single priority.
  • Enables enhanced QoS and timestamp support.
  • Performs ingress packet prioritization based on Layer 2 or Layer 3 headers.
  • Enables the flow-control of the SPAs.
  • Distributes line clocking reference from a single SPA to the RPs.
  • From Release 3.7.0S onward, the Cisco ASR1000-SIP40 is supported on all the routers that support the Cisco ASR1000-SIP10.

NoteThe Cisco ASR1000-SIP40 supports four half-height SPAs, two full-height SPAs, and a combination of two half-height and one full-height SPAs. The Cisco ASR1000-SIP40 does not support double-wide SPAs, and double-high SPAs having two connectors. The Cisco ASR1000-SIP40 supports four half-height SPAs, two full-height SPAs, and a combination of two half-height and one full-height SPAs. The Cisco ASR1000-SIP40 does not support double-wide SPAs, and double-high SPAs having two connectors.


The LEDs on the modules are the same for both the Cisco ASR1000-SIP10 and Cisco ASR1000-SIP40.

The following sections describe the Cisco ASR1000-SIP40:

Cisco ASR1000-SIP40 LEDs

The Cisco ASR1000-SIP40 has two LEDs, as shown in Figure 1-4.

Figure 1-4 Cisco ASR1000-SIP40 Faceplate

 


The Cisco ASR1000-SIP40 LEDs are described in Table 1-6 .

1

SPA, subslot 0

4

PWR LED

2

SPA, subslot 1

5

STATUS LED

3

SPA, subslot 2

6

SPA, subslot 3

 

Table 1-6 Cisco ASR1000-SIP40 LEDs

LED Label
Color
State
Meaning

STATUS

Red

On

The Cisco ASR1000-SIP40 has encountered an error.

 

Yellow

On

The Cisco ASR1000-SIP40 is loading.

 

Green

On

The Cisco ASR1000-SIP40 is online.

 

Off

Off

The Cisco ASR1000-SIP40 is powered off.

PWR

Green

On

The Cisco ASR1000-SIP40 is powered on.

 

Off

Off

The Cisco ASR1000-SIP40 is powered off.

Cisco ASR1000-SIP40 Physical Specifications

The Cisco ASR1000-SIP40 physical specifications are shown in Table 1-7 .

 

Table 1-7 Cisco ASR1000-SIP40 Physical Specifications

Description
Specifications

Physical dimension (HxWxD)

1.630 inches (41.4 mm) x 16.725 inches (424.8 mm) x 14.187 inches (360.3 mm)

Shipping weight

8.5 lb (3.9 kg)

Operating temperature

Nominal—40.9 to 104°F (5 to 40°C)
Short Term—40.9 to 131°F (5 to 55°C)

Relative humidity

Operating Humidity Nominal—5% to 85% noncondensing
Operating Humidity Short Term—5% to 90% noncondensing

Storage temperature

–40F to 158F (–40°C to 70°C)

Cisco ASR 1013 Router and Slot Numbering for SIP

The Cisco ASR 1013 Router supports the Cisco ASR1000-SIP40 and Cisco ASR1000-SIP10. In the Cisco ASR 1013 Router, the Cisco ASR 1000 Series SIP supports:

  • Four half-height SPAs with up to 24 ports per SPA
  • Two full-height SPAs with up to 48 ports per SPA
  • Two half-height and one full-height SPA combination that does not exceed 96 ports

The Cisco ASR 1013 Router uses the same SPA subslot numbering as the Cisco ASR 1006 Router and Cisco ASR 1004 Router.

Figure 1-5 Cisco ASR 1013 Router SPA Interface Slot Numbering

 

Figure 1-6 shows the slot numbering for the shared port adapters on the Cisco ASR 1013 Routers.


NoteThe Cisco ASR1000-ESP10 and Cisco ASR1000-ESP20 will not plug into the Cisco ASR 1013 Router ESP slots. The Cisco ASR 1013 Router supports six SIP slots only with the combination of Cisco ASR1000-ESP40 and RP2. The Cisco ASR1000-ESP10 and Cisco ASR1000-ESP20 will not plug into the Cisco ASR 1013 Router ESP slots. The Cisco ASR 1013 Router supports six SIP slots only with the combination of Cisco ASR1000-ESP40 and RP2.


Figure 1-6 Cisco ASR 1013 Router SPA Interface Slot Numbering

 

1

SPA—Slot 0

6

SPA—Slot 5

2

SPA—Slot 1

7

RP-2—R1

3

SPA—Slot 2

8

ESP-40/ESP-100—F1

4

SPA—Slot 3

9

RP-Filler—F0

5

SPA—Slot 4

10

RP-2—R0