Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide
Using the Configuration/Setup Utility Program
Downloads: This chapterpdf (PDF - 86.0KB) The complete bookPDF (PDF - 5.74MB) | Feedback

Using the Configuration/Setup Utility Program

Table Of Contents

Using the Configuration/Setup Utility Program

About the Configuration/Setup Utility Program

Starting the Configuration/Setup Utility Program

Configuration/Setup Utility Menu Options


Using the Configuration/Setup Utility Program


This appendix describes the Configuration/Setup Utility program and contains the following sections:

About the Configuration/Setup Utility Program

Starting the Configuration/Setup Utility Program

Configuration/Setup Utility Menu Options

About the Configuration/Setup Utility Program

The Configuration/Setup Utility program is part of the basic input/output system (BIOS) code in your WAE device. Use the Configuration/Setup Utility program to accomplish the following tasks:

View configuration information

View and change assignments for devices and I/O ports

Set the date and time

Set and change passwords

Set and change the startup characteristics of the device and the order of startup devices (startup-drive sequence)

Set and change settings for advanced hardware features

View, set, and change settings for power-management features

View and clear the error log

Enable USB keyboard and mouse support

Starting the Configuration/Setup Utility Program

To start the Configuration/Setup Utility program, follow these steps:


Step 1 Turn on the device.

Step 2 When the prompt Press F1 for Configuration/Setup appears, press F1.

If you have set both a user (power-on) password and a supervisor (administrator) password, you must type the supervisor password to access the full Configuration/Setup Utility menu. If you do not type the supervisor password, a limited Configuration/Setup Utility menu is available.

Step 3 Follow the instructions in the window.

Step 4 Choose the settings to view or change.


Configuration/Setup Utility Menu Options

The following choices are on the Configuration/Setup Utility main menu. Depending on the version of your BIOS code, some menu choices might differ slightly from these descriptions.

System Summary

Choose this option to view configuration information, including the type, speed, and cache sizes of the microprocessors and the amount of installed memory. When you make configuration changes through other options in the Configuration/Setup Utility program, the changes are reflected in the system summary; you cannot change settings directly in the system summary.

This option is on the full and limited Configuration/Setup Utility menu.

System Information

Choose this option to view information about your device. When you make changes through other options in the Configuration/Setup Utility program, some of those changes are reflected in the system information; you cannot change settings directly in the system information.

This option is on the full Configuration/Setup Utility menu only.

Product Data

Choose this option to view the machine type and model of your device, the serial number, and the revision level or issue date of the BIOS code stored in electrically erasable programmable ROM (EEPROM).

System Card Data

Choose this option to view the identity of the system board, power supplies, DASD backplane, and power backplane.

Devices and I/O Ports

Choose this option to view or change assignments for devices and input/output (I/O) ports.

Choose this option to enable or disable integrated SAS and Ethernet controllers and all standard ports (such as serial and parallel). If you disable a device, it cannot be configured, and the operating system will not be able to detect it (this is equivalent to disconnecting the device).

This option is on the full Configuration/Setup Utility menu only.

Date and Time

Choose this option to set the date and time in the device in 24-hour format (hour:minute:second). This option is on the full Configuration/Setup Utility menu only.

System Security

Choose this option to set passwords. This option is on the full Configuration/Setup Utility menu only.

Start Options

Choose this option to view or change the start options. Startup sequences take effect when you start the device. The startup sequence specifies the order in which the device checks devices to find a boot record. The device starts from the first boot record that it finds.

This option is on the full Configuration/Setup Utility menu only.

Advanced Setup

Choose this option to change settings for advanced hardware features.


Caution The device might malfunction if these options are incorrectly configured. Follow the instructions in the window carefully.

This option is on the full Configuration/Setup Utility menu only.

Event/Error Logs

Choose this option to view the three most recent error codes and messages that the system generated during POST. You can use the arrow keys to move between pages in the error log. Choose Clear POST Error Log to clear the POST error log.

Save Settings

Choose this option to save the changes you have made in the settings.

Restore Settings

Choose this option to cancel the changes you have made in the settings and restore the previous settings.

Load Default Settings

Choose this option to cancel the changes you have made in the settings and restore the factory settings.

Exit Setup

Choose this option to exit from the Configuration/Setup Utility program. If you have not saved the changes you have made in the settings, you are asked whether you want to save the changes or exit without saving them.