Catalyst 6500 Series Switch ISSU Upgrade Procedure with 6800IA (FEX) Connected
Available Languages
Contents
Introduction
This document describes a step-by-step In-Service Software Upgrade (ISSU) procedure on Cisco Catalyst 6500 Series Switches in Virtual Switching System (VSS) mode with the use of the Supervisor 2T with dual-homed Cisco Catalyst 6800 Instant Access Switches (FEX) attached.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on Cisco Catalyst 6500 Series Switches in VSS mode that run Supervisor Engine 2T with a dual-homed 6800IA attached on WS-X6904-40G linecards.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Upgrade Procedure
Initial Setup
The upgrade procedure is performed for Cisco IOS® Software Release 15.1(2)SY to Release 15.1(2)SY1.
Here are the statistics before the ISSU process:
- The Catalyst 6500 chassis with Switch ID 1 is Active and the Switch with ID 2 is Standby (Hot).
- Both of the chassis are up on Cisco IOS Software Release 15.1(2)SY.
- A single 6800IA that runs Cisco IOS software Release 15.0(2)EX2 is connected to VSS on WS-X6904-40G linecards with a dual-home connection. The FEX port-channel number is 99 and the FEX ID is 110.
6K1#show mod sw all
Switch Number: 1 Role: Virtual Switch Active
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1632K9P2
3 20 DCEF2T 4 port 40GE / 16 port 10GE WS-X6904-40G SAL1741E4ZA
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 c471.fe7c.de96 to c471.fe7c.de9d 1.3 12.2(50r)SYS 15.1(2)SY Ok
3 e02f.6d6a.698c to e02f.6d6a.699f 1.0 12.2(50r)SYL 15.1(2)SY Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Policy Feature Card 4 VS-F6K-PFC4 SAL1637MCQQ 1.2 Ok
2 CPU Daughterboard VS-F6K-MSFC5 SAL1637MKX8 1.4 Ok
3 Distributed Forwarding Card WS-F6K-DFC4-E SAL1745FSD6 1.0 Ok
Mod Online Diag Status
---- -------------------
2 Pass
3 Pass
Switch Number: 2 Role: Virtual Switch Standby
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 5 Supervisor Engine 2T 10GE w/ CTS (Hot) VS-SUP2T-10G SAL1650UC8L
3 20 DCEF2T 4 port 40GE / 16 port 10GE WS-X6904-40G SAL17173QD3
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 2c54.2dc4.2f3a to 2c54.2dc4.2f41 1.4 12.2(50r)SYS 15.1(2)SY Ok
3 70ca.9b8f.510c to 70ca.9b8f.511f 1.0 12.2(50r)SYL 15.1(2)SY Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Policy Feature Card 4 VS-F6K-PFC4 SAL1651UG8P 1.2 Ok
2 CPU Daughterboard VS-F6K-MSFC5 SAL1651UEBY 1.5 Ok
3 Distributed Forwarding Card WS-F6K-DFC4-E SAL17173QHY 1.2 Ok
Mod Online Diag Status
---- -------------------
2 Pass
3 Pass
Switch Number: 110 Role: FEX
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 C6800IA 48GE C6800IA-48TD FOC1736W1A6
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 c025.5cc2.2d00 to c025.5cc2.2d33 0.0 Unknown 15.0(2)EX2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
6K1#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 1
Local switch operational role: Virtual Switch Active
Peer switch number : 2
Peer switch operational role : Virtual Switch Standby
Upgrade Steps
- Make sure that the new Cisco IOS image (Cisco IOS software Release 15.1(2)SY1) is present in the bootdisk and the slavebootdisk.
6K1#dir bootdisk: | in s2t54
5 -rw- 120035816 Jan 23 2014 22:35:12 +00:00
s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
8 -rw- 119792104 Feb 10 2014 19:42:12 +00:00
s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
6K1#dir slavebootdisk: | in s2t54
5 -rw- 120035816 Jan 23 2014 22:26:14 +00:00
s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
8 -rw- 119792104 Feb 10 2014 19:46:14 +00:00
s2t54-adventerprisek9-mz.SPA.151-2.SY.bin - (Optional) Use these commands in order to verify that the VSS is ready to run the upgrade procedure:
- show issu state detail
- show redundancy
- show module switch all
- 6K1#show issu state detail
The system is configured to be upgraded in staggered mode.
Two supervisor nodes are found to be online.
Summary: the system will be upgraded in in-tandem mode.Slot = 1/2
RP State = Active
ISSU State = Init
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
Operating Mode = sso
ISSU Sub-State = No Upgrade Operation in Progress
Starting Image = N/A
Target Image = N/A
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Slot = 2/2
RP State = Standby
ISSU State = Init
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
Operating Mode = sso
ISSU Sub-State = No Upgrade Operation in Progress
Starting Image = N/A
Target Image = N/A
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_INIT
6K1#
6K1#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 36 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 1/2
Current Software state = ACTIVE
Uptime in current state = 36 minutes
Image Version = Cisco IOS Software, s2t54 Software
(s2t54-ADVENTERPRISEK9-M),
Version 15.1(2)SY, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 04-Sep-13 12:37 by prod_rel_team
BOOT = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer Processor Information :
----------------------------
Standby Location = slot 2/2
Current Software state = STANDBY HOT
Uptime in current state = 34 minutes
Image Version = Cisco IOS Software, s2t54 Software
(s2t54-ADVENTERPRISEK9-M),
Version 15.1(2)SY, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 04-Sep-13 12:37 by prod_rel_team
BOOT = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
- Use the issu loadversion command in order to start the upgrade process.
In this step, the VSS standby chassis reboots, reloads with the new image, and initializes as the VSS standby chassis in SSO redundancy mode, running the new image. This step is complete when the chassis configuration is synchronized, as indicated by the Bulk sync succeeded message. It might take several seconds to a few minutes for the new image to load and for the VSS standby chassis to transition to SSO mode.6K1#issu loadversion 1/2 bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
2/2 slavebootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
System configuration has been modified. Save? [yes/no]: yes
Building configuration...
[OK]
%issu loadversion initiated successfully, upgrade sequence will begin shortly
6K1#
*Feb 11 05:24:40.091: %ISSU_PROCESS-SW1-3-LOADVERSION: Loadversion sequence
will begin in 60 seconds. Enter 'issu abortversion' to cancel.
*Feb 11 05:25:10.091: %ISSU_PROCESS-SW1-6-LOADVERSION_INFO: Resetting Standby shortly
<..output truncated..>
*Feb 11 05:29:46.075: %VS_GENERIC-SW1-6-VS_HA_HOT_STANDBY_NOTIFY: Standby switch
is in Hot Standby mode
*Feb 11 05:29:46.079: %HA_CONFIG_SYNC-SW1-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded
*Feb 11 05:29:46.079: %RF-SW1-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
*Feb 11 05:30:25.091: %ISSU_PROCESS-SW1-3-LOADVERSION: Loadversion has completed.
Please issue the 'issu runversion' command after all modules come online.
!
! Boot variable for standby should point to new Image in "show issu state detail" output.
6K1#show issu state det
The system is configured to be upgraded in staggered mode.
2 supervisor nodes are found to be online.
Summary: an in-tandem upgrade is in progress.
Slot = 1/2
RP State = Active
ISSU State = Load Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
Operating Mode = sso
ISSU Sub-State = Load Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Slot = 2/2
RP State = Standby
ISSU State = Load Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Operating Mode = sso
ISSU Sub-State = Load Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_UPGRADE_INIT
6K1#show redundancy states
my state = 13 -ACTIVE
peer state = 8 -STANDBY HOT
Mode = Duplex
Unit = Secondary
Unit ID = 18
Redundancy Mode (Operational) = sso
Redundancy Mode (Configured) = sso
Redundancy State = sso
Maintenance Mode = Disabled
Manual Swact = enabled
Communications = Up
client count = 144
client_notification_TMR = 30000 milliseconds
keep_alive TMR = 9000 milliseconds
keep_alive count = 1
keep_alive threshold = 19
RF debug mask = 0x0 - When the VSS standby chassis successfully runs the new image in the SSO redundancy state and all of the linecards on the VSS standby chassis are up and online, enter the issu runversion command in order to force a switchover. The upgraded VSS standby chassis takes over as the new active chassis, running the new image. The formerly active chassis reloads and initializes as the new VSS standby chassis in SSO mode, running the old image (in case the software upgrade needs to be aborted and the old image restored). This step is complete when the chassis configuration is synchronized, as indicated by the Bulk sync succeeded message.
6K1#issu runversion
This command will reload the Active unit.Proceed ? [confirm]
%issu runversion initiated successfully
*Feb 11 05:35:19.035: %RF-SW1-5-RF_RELOAD: Self reload. Reason: Admin ISSU
runversion CLI
<..output truncated..>
Feb 11 05:35:21.411: %SYS-SW1-5-SWITCHOVER: Switchover requested by Exec.
Reload Reason: Admin ISSU runversion CLI.
Resetting .......
!
!Standby chassis now becomes active. Below logs are from new active switch.
!
Initializing as Virtual Switch ACTIVE processor
.
.
*Feb 11 05:37:36.107: %PFREDUN-SW2-6-ACTIVE: Standby initializing for SSO mode
*Feb 11 05:39:56.563: %HA_CONFIG_SYNC-SW2-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded
*Feb 11 05:39:56.563: %RF-SW2-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
*Feb 11 05:39:56.555: %PFREDUN-SW1_STBY-6-STANDBY: Ready for SSO mode in Default Domain
! Wait till all the modules and Fex Port-channel 99 links come up
!
*Feb 11 05:41:28.467: %ISSU_PROCESS-SW2-6-RUNVERSION_INFO: Runversion has completed.
Please issue the 'issu acceptversion' command
Feb 11 05:43:13.034: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/0/2, changed
state to up (FEX-110)
Feb 11 05:43:14.033: %LINEPROTO-5-UPDOWN: Line protocol on Interface
TenGigabitEthernet1/0/2, changed state to up (FEX-110)
*Feb 11 05:43:14.491: %SATMGR-SW2-5-FABRIC_PORT_UP: SDP up on interface Te1/3/5,
connected to FEX 110, uplink 52
*Feb 11 05:43:14.491: %SATMGR-SW2-5-DUAL_ACTIVE_DETECT_CAPABLE: channel group 99
is now dual-active detection capable
6K1#show issu state
The system is configured to be upgraded in staggered mode.
2 supervisor nodes are found to be online.
Summary: an in-tandem upgrade is in progress.
Slot = 2/2
RP State = Active
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Slot = 1/2
RP State = Standby
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_UPGRADE_INIT
6K1#show fex 110 detail
FEX: 110 Description: FEX0110 state: online
FEX version: 15.0(2)EX2
Extender Model: C6800IA-48TD, Extender Serial: FOC1736W1A6
FCP ready: yes
Image Version Check: enforced
Fabric Portchannel Ports: 2
Fabric port for control traffic: Te2/3/5
Fabric interface state:
Po99 - Interface Up.
Te1/3/5 - Interface Up. state: bound
Te2/3/5 - Interface Up. state: bound - Use the issu acceptversion command in order to stop the Rollback Timer. This is necessary because if the timer expires, the upgraded chassis reloads and reverts to the previous software version.
6K1#issu acceptversion
% Rollback timer stopped. Please issue the 'issu commitversion' command. - Use the issu runversion fex all command in order to start the image download and upgrade procedure on the FEX (6800IA). The FEX triggers the image download from the new software bundle of the Supervisor2T (here Cisco IOS software Release 15.2(2)SY1). If you use FEX stacks, the master is responsible to extract the image to its members. A TFTP server runs at 192.1.1.1.
6K1#issu runversion fex all
% Successfully initiated 'runversion fex' for Fex IDs: 110.
Use 'show issu state' for more information.
6K1#show issu state det
The system is configured to be upgraded in staggered mode.
2 supervisor nodes are found to be online.
Summary: an in-tandem upgrade is in progress.
Slot = 2/2
RP State = Active
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;bootdisk:
s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Operating Mode = sso
ISSU Sub-State = Run Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Slot = 1/2
RP State = Standby
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
Operating Mode = sso
ISSU Sub-State = Run Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_UPGRADE_IN_PROGRESS
Following are the logs on from FEX 6800IA console:
!
!192.1.1.1 is the tftp running on FEX controller i.e. VSS active and vlan 1012 is the
control vlan associated with fex.
!
FEX-110#
Loading c6800ia-universalk9-mz.150-2.EX4.bin from 192.1.1.1
(via Vlan1012): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 15493122 bytes]
examining image...
extracting info (112 bytes)
extracting c6800ia-universalk9-mz.150-2.EX4/info (792 bytes)
extracting info (112 bytes)
Stacking Version Number: 1.55
System Type: 0x00000000
Ios Image File Size: 0x00EB5200
Total Image File Size: 0x00EC6A00
Minimum Dram required: 0x08000000
Image Suffix: universalk9-150-2.EX4
Image Directory: c6800ia-universalk9-mz.150-2.EX4
Image Name: c6800ia-universalk9-mz.150-2.EX4.bin
Image Feature: IP|LAYER_2|SSH|3DES|MIN_DRAM_MEG=128
FRU Module Version: No FRU Version Specified
Old image for switch 1: flash:/c6800ia-universalk9-mz.150-2.EX2
Old image will be left alone
Extracting images from archive into flash...
! The console will be waiting for about 5-10 minutes after the above line.
<output truncated>
New software image installed in flash:/c6800ia-universalk9-mz.150-2.EX4
Following are the logs from the 6500 Active supervisor:
*Feb 11 06:00:30.387: %SATMGR-SW2-5-ONLINE: FEX 110 online
*Feb 11 06:00:30.391: %SATMGR-SW2-5-FEX_MODULE_ONLINE: FEX 110, module 1 online
*Feb 11 06:00:30.395: %OIR-SW2-6-INSREM: Switch 110 Physical Slot 1 - Module
Type LINE_CARD inserted
*Feb 11 06:00:30.951: %SATMGR-SW2-5-FABRIC_PORT_UP: SDP up on interface Te2/3/5,
connected to FEX 110, uplink 51
*Feb 11 06:00:30.951: %SATMGR-SW2-5-DUAL_ACTIVE_DETECT_CAPABLE: channel group
99 is now dual-active detection capable
*Feb 11 06:01:00.983: %OIR-SW2-6-SP_INSCARD: Card inserted in Switch_number =
110, physical slot 1, interfaces are now online
FEX-110#show ver | in image
System image file is "flash:/c6800ia-universalk9-mz.150-2.EX4/
c6800ia-universalk9-mz.150-2.EX4.bin"
6K1#show issu state det
The system is configured to be upgraded in staggered mode.
2 supervisor nodes are found to be online.
Summary: an in-tandem upgrade is in progress.
Slot = 2/2
RP State = Active
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Operating Mode = sso
ISSU Sub-State = Run Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Slot = 1/2
RP State = Standby
ISSU State = Run Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12;
Operating Mode = sso
ISSU Sub-State = Run Version Completed
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_UPGRADE_COMPLETE - In order to continue, enter the issu commitversion command to upgrade the VSS standby chassis and complete the ISSU sequence. The VSS standby chassis reboots, reloads with the new image, and initializes as the VSS standby chassis in the SSO redundancy state, running the new image. This step is complete when the chassis configuration is synchronized, as indicated by the Bulk sync succeeded message, and all of the linecards on the new VSS-Standby are up and online.
6K1#issu commitversion
%issu commitversion initiated successfully, upgrade sequence will continue shortly
6K1#
*Feb 11 06:05:30.839: %ISSU_PROCESS-SW2-3-COMMITVERSION: issu commitversion;
Commitversion sequence will begin in 60 seconds. Enter 'issu abortversion'
to cancel.
*Feb 11 06:06:00.839: %ISSU_PROCESS-SW2-6-COMMITVERSION_INFO:
Resetting Standby shortly
*Feb 11 06:08:48.571: %PFREDUN-SW2-6-ACTIVE: Standby initializing for SSO mode
*Feb 11 06:09:01.163: %ISSU_PROCESS-SW2-6-COMMITVERSION_INFO: Standby has
come online, wait for terminal state
.
.
*Feb 11 06:10:41.267: %VS_GENERIC-SW2-6-VS_HA_HOT_STANDBY_NOTIFY: Standby switch
is in Hot Standby mode
*Feb 11 06:10:41.271: %HA_CONFIG_SYNC-SW2-6-BULK_CFGSYNC_SUCCEED:
Bulk Sync succeeded
*Feb 11 06:10:41.271: %RF-SW2-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
*Feb 11 06:10:46.403: %ISSU_PROCESS-SW2-6-COMMITVERSION_INFO: Upgrade has completed,
updating boot configuration
!
!Boot variable now displays both new and old image in ?show issu state detail? output.
!
6K1#show issu state detail
The system is configured to be upgraded in staggered mode.
2 supervisor nodes are found to be online.
Summary: an in-tandem upgrade is in progress.
Slot = 2/2
RP State = Active
ISSU State = Commit Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Operating Mode = sso
ISSU Sub-State = Commit Version completed, waiting for system to settle
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Slot = 1/2
RP State = Standby
ISSU State = Commit Version
Boot Variable = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
Operating Mode = sso
ISSU Sub-State = Commit Version completed, waiting for system to settle
Starting Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
Target Image = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
Current Version = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin
This system is Fex-capable
Fex-ID ISSU Status
110 FEX_UPGRADE_COMPLETE
6K1#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 1 hour, 28 minutes
Switchovers system experienced = 1
Standby failures = 1
Last switchover reason = user forced
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 2/2
Current Software state = ACTIVE
Uptime in current state = 36 minutes
Image Version = Cisco IOS Software, s2t54 Software
(s2t54-ADVENTERPRISEK9-M), Version 15.1(2)SY1, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 28-Nov-13 12:58 by prod_rel_team
BOOT = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer Processor Information :
----------------------------
Standby Location = slot 1/2
Current Software state = STANDBY HOT
Uptime in current state = 1 minute
Image Version = Cisco IOS Software, s2t54 Software (s2t54-ADVENTERPRISEK9-M),
Version 15.1(2)SY1, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 28-Nov-13 12:58 by prod_rel_team
BOOT = bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY1.bin,12;
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin,12
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Verify
In order to verify that the upgrade was successful, use these commands:
- show issu state detail
- show redundancy
- show module switch all
Here is the current state after the ISSU process:
- 6500 chassis with Switch ID 2 is Active and the Switch with ID 1 is Standby (Hot). They are now on Cisco IOS Software Version 15.1(2)SY1.
- The Instant Access client (6800IA) now runs Cisco IOS Software Release 15.0(2)EX4.
6K1#show mod swi all
Switch Number: 1 Role: Virtual Switch Standby
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 5 Supervisor Engine 2T 10GE w/ CTS (Hot) VS-SUP2T-10G SAL1632K9P2
3 20 DCEF2T 4 port 40GE / 16 port 10GE WS-X6904-40G SAL1741E4ZA
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 c471.fe7c.de96 to c471.fe7c.de9d 1.3 12.2(50r)SYS 15.1(2)SY1 Ok
3 e02f.6d6a.698c to e02f.6d6a.699f 1.0 12.2(50r)SYL 15.1(2)SY1 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Policy Feature Card 4 VS-F6K-PFC4 SAL1637MCQQ 1.2 Ok
2 CPU Daughterboard VS-F6K-MSFC5 SAL1637MKX8 1.4 Ok
3 Distributed Forwarding Card WS-F6K-DFC4-E SAL1745FSD6 1.0 Ok
Mod Online Diag Status
---- -------------------
2 Pass
3 Pass
Switch Number: 2 Role: Virtual Switch Active
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1650UC8L
3 20 DCEF2T 4 port 40GE / 16 port 10GE WS-X6904-40G SAL17173QD3
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 2c54.2dc4.2f3a to 2c54.2dc4.2f41 1.4 12.2(50r)SYS 15.1(2)SY1 Ok
3 70ca.9b8f.510c to 70ca.9b8f.511f 1.0 12.2(50r)SYL 15.1(2)SY1 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Policy Feature Card 4 VS-F6K-PFC4 SAL1651UG8P 1.2 Ok
2 CPU Daughterboard VS-F6K-MSFC5 SAL1651UEBY 1.5 Ok
3 Distributed Forwarding Card WS-F6K-DFC4-E SAL17173QHY 1.2 Ok
Mod Online Diag Status
---- -------------------
2 Pass
3 Pass
Switch Number: 110 Role: FEX
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 C6800IA 48GE C6800IA-48TD FOC1736W1A6
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 c025.5cc2.2d00 to c025.5cc2.2d33 0.0 Unknown 15.0(2)EX4 Ok
Mod Online Diag Status
---- -------------------
1 Pass
6K1#
6K1#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 2
Local switch operational role: Virtual Switch Active
Peer switch number : 1
Peer switch operational role : Virtual Switch Standby
FeedbackContact Cisco
- Open a Support Case
- (Requires a Cisco Service Contract)