Guest

Cisco BPX/IGX/IPX WAN Software

IPX Frame Relay PAD Card (FRP) Hardware Error Decoding

Cisco - IPX Frame Relay PAD Card (FRP) Hardware Error Decoding

Document ID: 10815

Updated: Jun 07, 2006

   Print

Introduction

Cisco WAN Switching cards and modules log error codes when an anomaly occurs. Switch card errors are indicated to the user by a CD symbol at the bottom of the switch command line interface (CLI) screen. You can use the dspcderrs command to display a list of errors. The errors are presented based on access level.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

This document is not restricted to specific software and hardware versions.

Conventions

Refer to the Cisco Technical Tips Conventions for more information on document conventions.

IPX FRP Hardware Errors

This list in this section is a reference for IPX Frame Relay PAD Card (FRP) hardware errors presented up to the StrataCom-level. StrataCom-level errors are service-significant only. You might not see all errors listed.

=============================================================================

  ==== HARDWARE AND SOFTWARE error lists (hw_code.h)     BY MGC (09-30-92)

  ====

  ==== Present Revision: 2.0                                              

  ====

  ==== Revision History: FDE/FEE + FTC                   BY CvH (05-25-94)

  ====

  ====                   Added Self-Test Failures        BY CvH (06-22-94)

  ====

  ====                   Corrections                     BY CvH (08-18-94)

  ====

  ====                   Add non-ACP errors              BY CvH (08-18-94)

  ====

  =============================================================================

  

  *** GENERIC FATAL ERRORS **** 

  Hardware Error Message Format

   |Fcn Code (if due to a command, else 0)

   | |Error: 1 - download failure

   | | |     2 - power-up failure   

   | | |     3 - selftest failure   

   | | |     4 - memory test failure

   | | |     5 - internal boot failure   

   | | |     6 - internal ACP failure   

   | | |     7 - watchdog failure   

   | | |Slot/Type (Type if MSB set): 99 (19) if FRP, A3 (23) if FTC

   | | | |Processor Number

   | | | | |

  0B01029901 000000ii xxxxxxxx yyyyyyyy : Power-up Failure 

              i  = failure state

             05h - novram checksum failed           

             06h - fifo loopback failed

             07h - no state 0 msg from supv. (SRAM problem)

             10h - fifo test failed

             11h - no state 1 msg from supv.

          >= 12h - passed boot prom (missed handshake)

          x = failure address, y = data expected

  0B01049901 xxxxxxxx yyyyyyyy zzzzzzzz: Memory Test Failure 

          x = failure address, y = data expected, z = data received

  0B01059901 000000ii : Internal Boot Failure 

             i = failure mode

             0 - waiting for HF flag change from DSP

             1 - waiting for TXDE flag to go true from DSP

             2 - waiting for RXDF flag to go true from DSP

             3 - unable to initialize DSP

             4 - unable to internal load DSP

             5 - unable to program EEPROM

             6 - bad message from CBUS controller

             7 - 9th bit/msg format error from supv.

             8 - no NMICLR in response to NMI to supv.

             9 - timeout waiting for space in Admin fifo

  0B00079901 : 8751 Watchdog Timeout

  

  *** FATAL HARDWARE ERRORS **** (The byte count will be 17)

  

  0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16] : acp_stop Error     (@pc addr)

  0B00069901 FF 01 00 01 [ pc addr ] [err addr ] : pSOS K_FATAL Error (@pc addr)

      error usually a pSOS code: 4B = max. num. cnfg. timers exceeded

  

  *** FATAL ADDRESS/BUS EXCEPTION ERRORS **** (The byte count will be 23)

  

  0B00069901 FF 01 00 00 [sr:16][pc addr][vo:16][ssw:16][fault addr] 

  

  *** NON-FATAL HARDWARE ERRORS **** (The byte count will be 13)

  

  0B00069901 01 00 00 C0 [lcn      ] : Expect psos message (test frame)

  0B00069901 01 00 ii C1 00 00 00 00 : DIAGS test aborted in tm on; i = port

  0B00069901 01 00 ii C3 [message  ] : Loopback frm not received; i = port

  0B00069901 01 00 ii C4 [hchannel ] : Loopback frm bad hch number; i = port

  0B00069901 01 00 ii C5 [length   ] : Loopback frm bad frame length; i = port

  0B00069901 01 00 ii C6 [address  ] : Loopback frm incorrect data; i = port

  0B00069901 01 00 ii C7 [address  ] : Loopback frm zero segment; i = port

  0B00069901 01 00 ii C8 [testnum  ] : Invalid test number (diags); i = port

  0B00069901 01 00 00 C9 [bc type  ] : Bad internal card type

  0B00069901 01 00 ii C9 00 00 00 00 : DIAGS test aborted in tm off; i = port

  0B00069901 01 01 00 80 [response ] : Bad SLOT ID response (startup)

  0B00069901 01 01 00 90 00 00 00 00 : Bad watch dog timer event rcvd (cmd_task)

  0B00069901 01 01 D0 00 [status   ] : FPTX HP failure status during dnld

  0B00069901 01 01 D0 01 [status   ] : FPTX watchdog HP failure status

  0B00069901 01 01 D0 02 [status   ] : FPTX activate HP error status

  0B00069901 01 01 D0 03 [status   ] : FPTX deactivate HP error status

  0B00069901 01 01 D0 04 [status   ] : FPTX write command HP error status

  0B00069901 01 01 D0 05 [status   ] : FPTX read command HP error status

  0B00069901 01 01 D0 06 [status   ] : FPTX self test HP error status

  0B00069901 01 01 D0 07 [status   ] : FPTX activate: HP status bad

  0B00069901 01 01 D0 08 [status   ] : FPTX purge: HP status bad

  0B00069901 01 01 D0 09 [status   ] : FPTX purge all: HP status bad

  0B00069901 01 01 D0 0A [status   ] : FPTX suspend: HP status bad

  0B00069901 01 01 D0 0B [status   ] : FPTX resume: HP status bad

  0B00069901 01 01 D1 00 [status   ] : FPRX HP failure status during dnld

  0B00069901 01 01 D1 01 [status   ] : FPRX watchdog HP failure status

  0B00069901 01 01 D1 02 [status   ] : FPRX activate HP error status

  0B00069901 01 01 D1 03 [status   ] : FPRX deactivate HP error status

  0B00069901 01 01 D1 04 [status   ] : FPRX write command HP error status

  0B00069901 01 01 D1 05 [status   ] : FPRX read command HP error status

  0B00069901 01 01 D1 06 [status   ] : FPRX self test HP error status

  0B00069901 01 01 D1 07 [status   ] : FPRX cnfig MC HP status

  0B00069901 01 01 D1 08 [status   ] : FPRX stats bad HP status

                         [index    ] : STATS invalid stats buffer index

  0B00069901 01 01 D1 09 [status   ] : FPRX LCA boot response bad HP status

  0B00069901 01 01 D1 0A [status   ] : FPRX suspend cnfig MC HP status

  0B00069901 01 01 D1 0B [status   ] : FPRX resume cnfig MC HP status

  0B00069901 01 01 D2 00 [status   ] : DMA HP failure status during dnld

  0B00069901 01 01 D2 01 [status   ] : DMA watchdog HP failure status

  0B00069901 01 01 D2 02 [status   ] : DMA activate HP error status

  0B00069901 01 01 D2 03 [status   ] : DMA deactivate HP error status

  0B00069901 01 01 D2 04 [status   ] : DMA write command HP error status

  0B00069901 01 01 D2 05 [status   ] : DMA read command HP error status

  0B00069901 01 01 D2 06 [status   ] : DMA self test HP error status

  0B00069901 01 01 D2 07 [hch/stat ] : DMA HP msg failed @ enable channel

  0B00069901 01 01 D2 08 [hch/stat ] : DMA HP msg failed @ disable channel

  0B00069901 01 01 D2 0A [status   ] : DMA HP msg failed @ inc hp counter

  0B00069901 01 01 D2 0B [status   ] : DMA HP msg failed @ reset hp counter

  0B00069901 01 01 D2 0C [status   ] : DMA HP msg failed @ resume receive

  0B00069901 01 01 D2 0D [status   ] : DMA HP msg failed @ halt receive

  0B00069901 01 01 D2 0E [ts/stat  ] : DMA HP msg failed @ idle code

  0B00069901 01 01 D2 17 [code     ] : DMA enable channel msg code incorrect

  0B00069901 01 01 D2 18 [code     ] : DMA disable channel msg code incorrect

  0B00069901 01 01 D2 28 [length   ] : DMA disable channel msg len. incorrect

  0B00069901 01 02 00 8A [buf index] : FIFO cmd read too long/not end bit set

  0B00069901 01 02 00 8C [msg index] : FIFO cmd too long to write out

  0B00069901 01 02 00 8D 00 00 00 00 : Exceeded FIFO test wait time

  0B00069901 01 02 00 8E 00 00 00 00 : VC Table corrupted (    256 lcns)

  0B00069901 01 02 00 8F 00 00 00 00 : Complex GW con received OAM packet

  0B00069901 01 02 00 91 [Tmr 1 Cnt] : CIO Timer 1 Errors

  0B00069901 01 02 00 92 [Tmr 2 Cnt] : CIO Timer 2 Errors

  0B00069901 01 02 00 93 [Tmr 3 Cnt] : CIO Timer 3 Errors

  0B00069901 01 02 00 94 [Prt A Cnt] : CIO Port A Errors 

  0B00069901 01 02 00 95 [Prt B Cnt] : CIO Port B Errors 

  0B00069901 01 02 ii B0 00 00 00 00 : PRT_CTRL DxE setup failure;   i = port

  0B00069901 01 02 ii B1 [baudindex] : PRT_CTRL invalid baud rate;   i = port

  0B00069901 01 02 ii B2 [clkselect] : PRT_CTRL invalid clk select;  i = port

  0B00069901 01 02 ii B3 [timer cnt] : PRT_CTRL invalid pit count;   i = port

  0B00069901 01 02 ii B4 00 00 00 00 : BRSAMPLE invalid cntr value;  i = port

  0B00069901 01 02 ii B5 00 00 00 00 : BRSAMPLE invalid timer value; i = port

  0B00069901 01 02 ii B6 00 00 00 00 : BRSAMPLE zero elapsed time;   i = port

  0B00069901 01 02 ii B8 [eia lead ] : EIA_MON lead failure; i = port

  0B00069901 01 02 00 F2 [checksum ] : Bad novram checksum

  0B00069901 01 02 00 CA 00 00 00 ii : CAM_CTRL update_lcn_cam, inv. port = i

  0B00069901 01 02 01 CA 00 00 00 ii : CAM_CTRL clear_lcn_cam,  inv. port = i

  0B00069901 01 02 02 CA 00 00 00 ii : CAM_CTRL cam_lcn_lookup, inv. port = i

  

  0B00069901 D0 00 03 01 [data     ] : FPTX watchdog failure data

  0B00069901 D0 01 01 00 [length   ] : FPTX bad rsp length after dnld (dsp_ctrl)

  0B00069901 D0 01 01 01 [length   ] : FPTX watchdog response incorrect length

  0B00069901 D0 01 01 05 [length   ] : FPTX read command incorrect length

  0B00069901 D0 01 01 06 [length   ] : FPTX self test incorrect length  

  0B00069901 D0 01 01 09 [length   ] : FPTX purge all: incorrect length rtned

  0B00069901 D0 01 01 DB 00 00 00 00 : FPTX bootstrap failed

  0B00069901 D0 01 02 00 [code     ] : FPTX bad code rsp after dnld (dsp_ctrl)

  0B00069901 D0 01 02 01 [code     ] : FPTX watchdog incorrect fcn. code rtned

  0B00069901 D0 01 02 05 [code     ] : FPTX read command incorrect msg code

  0B00069901 D0 01 02 06 [code     ] : FPTX self test incorrect msg code

  0B00069901 D0 01 02 09 [code     ] : FPTX purge all: incorrect code returned

  0B00069901 D0 01 02 DB 00 00 00 00 : FPTX boot failed

  0B00069901 D0 01 03 00 [data     ] : FPTX bad data rsp after dnld (dsp_ctrl)

  0B00069901 D0 01 03 01 [data     ] : FPTX watchdog failure data

  0B00069901 D0 01 03 06 [status   ] : FPTX STSTS self-test error

  

  0B00069901 D1 00 03 01 [data     ] : FPRX watchdog failure data

  0B00069901 D1 01 01 01 [length   ] : FPRX watchdog response incorrect length

  0B00069901 D1 01 01 00 [length   ] : FPRX bad rsp length after dnld (dsp_ctrl)

  0B00069901 D1 01 01 05 [length   ] : FPRX read command incorrect length

  0B00069901 D1 01 01 06 [length   ] : FPRX self test incorrect length  

  0B00069901 D1 01 01 08 [length   ] : FPRX stats response bad length

  0B00069901 D1 01 01 09 [length   ] : FPRX LCA boot response bad length

  0B00069901 D1 01 01 DB 00 00 00 00 : FPRX bootstrap failed

  0B00069901 D1 01 02 00 [code     ] : FPRX bad code rsp after dnld (dsp_ctrl)

  0B00069901 D1 01 02 01 [code     ] : FPRX watchdog incorrect fcn code rtned

  0B00069901 D1 01 02 05 [code     ] : FPRX read command incorrect msg code

  0B00069901 D1 01 02 06 [code     ] : FPRX self test incorrect msg code

  0B00069901 D1 01 02 08 [code     ] : FPRX stats response bad code

  0B00069901 D1 01 02 09 [code     ] : FPRX LCA boot response bad code

  0B00069901 D1 01 02 DB 00 00 00 00 : FPRX boot failed

  0B00069901 D1 01 03 00 [data     ] : FPRX bad data rsp after dnld (dsp_ctrl)

  0B00069901 D1 01 03 01 [data     ] : FPRX watchdog failure data

  0B00069901 D1 01 03 06 [status   ] : FPRX STSTS self-test error

  0B00069901 D1 01 03 09 [data     ] : FPRX LCA boot error response data <> 0

  

  0B00069901 D2 00 03 01 [data     ] : DMA watchdog failure data

  0B00069901 D2 01 01 00 [length   ] : DMA bad rsp length after dnld (dsp_ctrl)

  0B00069901 D2 01 01 01 [length   ] : DMA watchdog response incorrect length

  0B00069901 D2 01 01 05 [length   ] : DMA read command incorrect length

  0B00069901 D2 01 01 06 [length   ] : DMA self test incorrect length  

  0B00069901 D2 01 01 09 [msg len  ] : DMA incorrect msg length  

  0B00069901 D2 01 01 DB 00 00 00 00 : DMA bootstrap failed

  0B00069901 D2 01 02 00 [code     ] : DMA bad code rsp after dnld (dsp_ctrl)

  0B00069901 D2 01 02 01 [code     ] : DMA watchdog incorrect fcn code rtned

  0B00069901 D2 01 02 05 [code     ] : DMA read command incorrect msg code

  0B00069901 D2 01 02 06 [code     ] : DMA self test incorrect msg code

  0B00069901 D2 01 02 09 [msg code ] : DMA incorrect msg code

  0B00069901 D2 01 02 DB 00 00 00 00 : DMA boot failed

  0B00069901 D2 01 03 00 [data     ] : DMA bad data rsp after dnld (dsp_ctrl)

  0B00069901 D2 01 03 01 [data     ] : DMA watchdog failure data

  0B00069901 D2 01 03 06 [status   ] : DMA STSTS self-test error

  0B00069901 D2 01 03 09 [msg data ] : DMA incorrect msg

  

  0B00069901 DB 02 01 00 [ISR ptr  ] : DSP not ready with TRDY

  0B00069901 DB 02 02 00 [ISR ptr  ] : DSP not ready with TXDE for bootstrap

  0B00069901 DB 02 03 00 [ISR ptr  ] : DSP not ready with TRDY for bootstrap

  0B00069901 DB 02 11 00 [ISR ptr  ] : DSP not ready with TXDE for boot

  0B00069901 DB 02 12 00 [ISR ptr  ] : DSP not ready for boot dnld

  0B00069901 DB 02 13 00 [ISR ptr  ] : DSP not ready with TRDY for boot

  0B00069901 DB 02 14 00 [ISR ptr  ] : DSP not ready with TXDE for boot

  0B00069901 DB 02 15 00 [ISR ptr  ] : DSP not ready with TRDY for boot

  

  0B00069901 DD 02 02 00 [ISR ptr  ] : DSP has not completed previous command

  0B00069901 DD 02 03 00 [CVR ptr  ] : DSP did not respond to sent command          

  0B00069901 DD 02 04 00 [ISR ptr  ] : DSP did not receive HP bytes

  0B00069901 DD 02 05 ii [ISR ptr  ] : DSP not ready to receive

  0B00069901 DD 02 06 00 [ISR ptr  ] : DSP did not ack command reception

  0B00069901 DD 02 07 00 [CVR ptr  ] : DSP not ready for "execute host" cmd

  0B00069901 DD 02 08 00 [ISR ptr  ] : DSP did not ack command completion

  0B00069901 DD 02 09 00 [ISR ptr  ] : DSP did not return HP command response

  0B00069901 DD 02 0A 00 [CVR ptr  ] : DSP not ready for slave read response

  0B00069901 DD 02 0B ii [ISR ptr  ] : DSP failed to return RXDF

  0B00069901 DD 02 0C 00 [CVR ptr  ] : DSP not ready for close output

  

  0B00069901 F0 01 00 03 [llcb_ptr ] : FREE_FRM: Frame Buffer Overflow (> Max FB/Frm)

  

  0B00069901 F1 01 00 03 [frm_ptr  ] : FTX_RECY: Frame Buffer Overflow (> Max FB/Frm)

  0B00069901 F1 01 00 05 00 00 00 00 : FTX_RECY: Spyder overrun

  0B00069901 F1 01 00 06 00 00 00 00 : FTX_RECY: Spyder underrun

  0B00069901 F1 01 00 07 [hpr_q_ptr] : FTX_PURG: Bad Hi-priority Q pointer

  0B00069901 F1 01 00 08 [lpr_q_ptr] : FTX_PURG: Bad Lo-priority Q pointer

  0B00069901 F1 01 00 09 [fim_q_ptr] : FIM_PURG: Bad Fim Q pointer

  0B00069901 F1 01 00 0D [dma error] : FTX_RECY: Undefined TX DMA Error

  

  0B00069901 F2 01 00 01 [fcb_tail ] : FRX_RECY: FCB Q overflow [Port only]

  0B00069901 F2 01 00 03 [frm_ptr  ] : FRX_RECY: Recycled too many frame bufs

  0B00069901 F2 01 00 04 [prev_fptr] : FRX_RXFR: SOF rcvd B4 last frame's EOF

                         [curr_fptr] : FRX_RXFR: (always comes in pairs)

  0B00069901 F2 01 00 05 [error    ] : FRX_RXFR: Unexpected DMA error code

  0B00069901 F2 01 00 06 00 00 00 00 : FRX_RXFR: SPYDER UNDERRUN

  0B00069901 F2 01 00 0A [pointer  ] : FRX_RXFR: DMA interrupt Q Overrun

  0B00069901 F2 01 00 0B [error    ] : FRX_RXFR: Undefined RX DMA error

  0B00069901 F2 01 00 0C [hyperch  ] : FRX_RECY: FB in use underrun (count)

  0B00069901 F2 01 00 0E [frm_ptr  ] : FRX_IDLE: Zero FB Reported (FRX_DLOK/DLC0/PTLB)

  0B00069901 F2 01 00 0F [hyperch  ] : FRX_RXFR: Invalid DMA hyperchannel

  0B00069901 F2 01 00 10 [pt_rx_ptr] : FRX_RXFR: Invalid DMA offset

  0B00069901 F2 01 00 11 [frm_ptr  ] : FRX_RXFR: Firmware Frame in Progress Error

  0B00069901 F2 01 00 12 [frm_ptr  ] : FRX_RXFR: Missing EOF Status

  0B00069901 F2 01 00 13 [frm_ptr  ] : FRX_RXFR: Sequence Error Status

  

  *** SOFTWARE ERRORS **** (The byte count will be 3)

  Guidelines for Error Codes:  0 - unknown function code

                               1 - illegal length

                               2 - illegal parameter

                               3 - unused

                               4 - illegal for card state

                               5 - illegal for channel state

                               6 - configuration error

                               7 - illegal for backcard state

  

  Error Code  Module     Error Reason

  ----------  --------   ---------------------------------------

  02 xx 00  : COMMAND  : Invalid command         *** SPECIAL ***

  02 xx 01  : COMMAND  : Invalid message length  *** SPECIAL ***

  02 03 03  : CMD_STST : Bad self test number ( != 0 or 1)

  02 03 04  : CMD_STST : FRIC not active

  02 18 02  : CMD_MEM  : Bad parameter (write_memory_cmd)

  02 19 02  : CMD_MEM  : Bad parameter ( read_memory_cmd)

  02 1A 04  : CMD_MEM  : Command not supported (memory_test_cmd)

  02 1B 02  : CMD_MEM  : Bad parameter (write_NOVRAM_cmd)

  02 1C 02  : CMD_MEM  : Bad parameter ( read_NOVRAM_cmd)

  02 1D 02  : CMD_LED  : Bad LED bitmap

  02 1E 02  : CMD_DBUG : Command not supported (scope_loop_cmd)

  02 1F 02  : CMD_DBUG : Invalid processor type (ascii_event_cmd)

  02 20 04  : CMD_DNLD : Command not supported (transfer_begin_cmd) [PORT]

  02 21 04  : CMD_DNLD : Command not supported (transfer_cmd)       [PORT]

  02 22 04  : CMD_DNLD : Command not supported (transfer_end_cmd)   [PORT]

  02 A0 02  : CMD_CFBC : Back card type mismatch

  02 A0 03  : CMD_CFBC : Bad BC state parameter (BC_RESET)

  02 A0 04  : CMD_CFBC : Bad BC state parameter (UNKNOWN)

  02 A1 02  : CMD_BCST : Port not configured yet

  02 A2 02  : CMD_ALM  : Port not configured yet

  02 A2 03  : CMD_ALM  : Back card type mismatch

  02 AB 04  : CMD_DCC  : Bad time slot number ( >= MAX_E1_TIMESLOTS)

  02 B0 02  : CMD_HCH  : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)

  02 B0 04  : CMD_HCH  : FRIC not active

  02 B0 05  : CMD_HCH  : Unallowd port reconfig (eg Bundled <=   Unbundled) 

  02 B0 06  : CMD_HCH  : Bad timeslot configuration

  02 B0 07  : CMD_HCH  : Timeslot number out of range

  02 B0 08  : CMD_HCH  : Timeslot already activated/deactivated

  02 B0 xx  : CMD_HCH  : Bad back card type (xx = rcvd back card type)

  02 B1 02  : CMD_PORT : Bad port ( >= Bd_Table.back_card_ports)

  02 B2 02  : CMD_HCST : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTST : Bad port ( >= Bd_Table.back_card_ports)

  02 B3 02  : EIA_EVT  : Bad port ( >= Bd_Table.back_card_ports) [PORT]

                         (get_port_eia_status_cmd)

  02 B4 02  : CARD_EVT : local bus param non-zero

  02 B7 04  : CMD_ICA  : FRIC not active

  02 B8 02  : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)

  02 B8 04  : CMD_HCCG : FRIC not active

  02 B9 02  : CMD_HCCG : Bad hyperchannel number ( >= MAX_HCHANNELS)

            : CMD_PTCG : Bad port ( >= Bd_Table.back_card_ports)

  02 BF 02  : CMD_DIAG : Bad port ( >= Bd_Table.back_card_ports) [PORT]

                         Bad test number ( != 1,2,3) [PORT]

                         Bad test number to terminate

  02 BF 03  : CMD_DIAG : Bad hyperchannel number ( >= MAX_HCHANNELS)

  02 BF 04  : CMD_DIAG : Hyperchannel/FRIC not active

  02 BF 05  : CMD_DIAG : Bad test number ( != 1, 2, or FF) [LINE]

            : CMD_DIAG : Port not active [PORT]

  02 BF 06  : CMD_DIAG : Bad test number to terminate

  02 BF 07  : CMD_DIAG : FRIC not active

  02 C0 02  : CMD_VC   : Bad hyperchannel number, DLCI, LCN

            : CMD_VC   : Bad DLCI, port ( >= Bd_Table.back_card_ports)

  02 C0 03  : CMD_VC   : Hch/port number doesn't match database for active LC

  02 C0 04  : CMD_VC   : FRIC not active

  02 C0 05  : CMD_VC   : VC already active (used by multicast) [REMOVE]

  02 C0 07  : CMD_VC   : VC already active

  02 C0 08  : CMD_VC   : FastPAD not active

  02 C1 02  : CMD_VC   : Bad LCN [REMOVE]

  02 C1 05  : CMD_VC   : VC already active (used by multicast) [REMOVE]

  02 C2 02  : CMD_VCST : Bad LCN [REMOVE]

  02 C5 02  : CMD_MC   : Command not supported

  02 C6 02  : CMD_MC   : Command not supported

  02 C7 02  : CMD_RTD  : Bad LCN [REMOVE]

  02 C7 04  : CMD_RTD  : FRIC not active

  02 C8 02  : CMD_VCCG : Bad LCN [REMOVE], LCN not active 

  02 C8 03  : CMD_VCCG : LCN not active

  02 C8 04  : CMD_VCCG : FRIC not active

  02 C9 02  : CMD_VCCG : Bad LCN [REMOVE]

  02 CC 02  : CMD_FPID : FRIC not active [PORT-FTC]

  02 CC 03  : CMD_FPID : Bad port ( >= MAX_PORT) [PORT-FTC]

  02 CC 04  : CMD_FPID : No match & no space found in Fp_Table [PORT-FTC]

  02 CC 05  : CMD_FPID : Bundling on Fp inconsistent with Port [PORT-FTC]

  

  

  *** SELF-TEST RESPONSES **** (from STSTS)

  Code                            Meaning

  ----------                      ---------------------------------------

  03 00                         : Done  (Success)

  03 80                         : Abort

  03 01 01 02 00 F0 00 00 00 00 : Fail - invalid FPTX self-test

  03 01 01 02 00 F0 00 00 00 01 : Fail - invalid FPRX self-test

  03 01 01 02 00 F0 00 00 00 02 : Fail - invalid DMA  self-test

  03 01 01 02 00 F2 xx xx yy yy : Fail - self_test_eeprom: x = calc.

  checksum,

                                         y = stored checksum @ 83FFFC

  03 01 01 02 xx F3 yy yy yy yy : Fail - self_test_routing_table: x =

  test,

                                         y = routing table address

  03 01 01 02 xx F4 yy yy yy yy : Fail - self_test_gram: x = test,

                                         y = GRAM address

  03 01 01 02 00 F5 [data & 30] : Fail - self_test_power_monitor

  03 01 D0 01 01 06 [  status ] : Fail - self_test_fptx

  03 01 D1 01 01 06 [  status ] : Fail - self_test_fprx

  03 01 D2 01 01 06 [  status ] : Fail - self_test_dma

  03 01 D2 CA CA ii xx xx yy yy : Fail - self_test_cam [LINE]

                                  i = data pattern, x = lcn, y = CAM lcn

Related Information

Updated: Jun 07, 2006
Document ID: 10815