Guest

Cisco MDS 9000 Series Multilayer Switches

Windows Server 2003 iSCSI Host to MDS/IPS-8 Configuration Example

Cisco - Windows Server 2003 iSCSI Host to MDS/IPS-8 Configuration Example

Document ID: 46060

Updated: Nov 29, 2005

   Print


Contents


Introduction

Cisco's iSCSI drivers, which reside on the server, are a key component of an iSCSI solution. These iSCSI drivers intercept SCSI commands, encapsulate them into IP packets, and redirect them to the Cisco SN 5420, Cisco SN 5428, Cisco SN5428-2, or Cisco MDS/IPS-8. This document provides sample configurations for Solaris iSCSI host to MDS/IPS-8.

Before You Begin

Conventions

Cisco MDS 9000 that is used in this document refers to any Fibre Channel (FC) switch product in the MDS 9000 family (MDS 9506, MDS 9509, MDS 9216).
IPS blade refers to IP Storage Services Module. For more information on document conventions, see the Cisco Technical Tips Conventions.

Prerequisites

  • Install the iSCSI driver that is compatible to your Windows Server 2003 version. The most current version of the driver can be found at the Cisco iSCSI Driver for Windows Server 2003 (registered customers only) page on Cisco.com. The README.txt file is included in the driver zip(tar) file. The README contains information about the license agreement, driver installation and configuration instructions, and a technical overview of the driver architecture.
  • The Cisco iSCSI Driver for Microsoft Windows 2003 requires Windows Server 2003 Enterprise Edition or Standard Edition or Web Edition.
  • Components Used

    The information in this document is based on the software and hardware versions below.

    • Host with Windows Server 2003 Standard Edition
    • Cisco iSCSI Driver 3.1.2 for Windows Server 2003. iSCSI driver version can be seen at the bottom left of the iSCSI Config window.
    • Cisco MDS 9216 with Software Version 1.2(1a)
    canterbury# show module 
    Mod  Ports  Module-Type                     Model              Status 
    ---  -----  ------------------------------- ------------------ ------------ 
    1    16     1/2 Gbps FC/Supervisor          DS-X9216-K9-SUP    active * 
    2    8      IP Storage Services Module      DS-X9308-SMIP      ok 
    
    Mod  Sw           Hw      World-Wide-Name(s) (WWN) 
    ---  -----------  ------  -------------------------------------------------- 
    1    1.2(1a)      1.0     20:01:00:0c:30:6c:24:40 to 20:10:00:0c:30:6c:24:40 
    2    1.2(1a)      0.3     20:41:00:0c:30:6c:24:40 to 20:48:00:0c:30:6c:24:40 
    
    Mod  MAC-Address(es)                         Serial-Num 
    ---  --------------------------------------  ---------- 
    1    00-0b-be-f8-7f-08 to 00-0b-be-f8-7f-0c  JAB070804QK 
    2    00-05-30-00-ad-e2 to 00-05-30-00-ad-ee  JAB070806SB 
    
    * this terminal session 
    Canterbury#show ver 
    Cisco Storage Area Networking Operating System (SAN-OS) Software 
    TAC support: http://www.cisco.com/tac 
    Copyright (c) 2002-2003 by Cisco Systems, Inc. All rights reserved. 
    The copyright for certain works contained herein are owned by 
    Andiamo Systems, Inc. and/or other third parties and are used and 
    distributed under license. 
    
    Software 
      BIOS:      version 1.0.8 
      loader:    version 1.1(2) 
      kickstart: version 1.2(1a) 
      system:    version 1.2(1a) 
    
      BIOS compile time:       08/07/03 
      kickstart image file is: bootflash:/k121a 
      kickstart compile time:  9/1/2003 17:00:00 
      system image file is:    bootflash:/s121a 
      system compile time:     9/1/2003 17:00:00 
    
    Hardware 
      RAM 960080 kB 
    
      bootflash: 500736 blocks (block size 512b) 
      slot0:          0 blocks (block size 512b) 
    
      Canterbury uptime is 1 days 12 hours 3 minute(s) 29 second(s) 
    
      Last reset at 39578 usecs after Mon Oct 13 07:32:38 2003 
        Reason: Reset Requested by CLI command reload 
        System version: 1.2(1a)
    

    The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.

    Background Theory

    The IP Storage module provides IP hosts access to FC storage devices. The IPS module is DS-X9308-SMIP. It provides transparent SCSI routing. IP hosts using iSCSI protocol can transparently access SCSI (FCP) targets on the FC network The IP host sends SCSI commands encapsulated in iSCSI protocol data units (PDUs) to a MDS 9000 IPS port over a TCP/IP connection. On the IPS module, connectivity is provided in the form of Gigabit Ethernet (GE) interfaces that are appropriately configured. The IPS module enables you to create virtual iSCSI targets and maps them to physical FC targets available in the FC SAN. It presents the FC targets to IP hosts as if the physical targets were locally attached to the IP network.

    Each iSCSI host that requires access to storage via the IPS module needs to have a compatible iSCSI driver installed. Using the iSCSI protocol, the iSCSI driver allows an iSCSI host to transport SCSI requests and responses over an IP network. From the perspective of a host operating system, the iSCSI driver appears to be a SCSI transport driver similar to a FC driver for a peripheral channel in the host. From the perspective of the storage device, each IP host appears as a FC host.

    Routing SCSI from the IP host to the FC storage device consists of the following main actions:

    • Transporting iSCSI requests and responses over an IP network between hosts and the IPS module.
    • Routing SCSI requests and responses between hosts on an IP network and the FC storage device (converting iSCSI to FCP and vice versa). This routing is performed by the IPS module.
    • Transporting FCP requests or responses between the IPS module and FC storage devices.
    The IP Storage module does not import FC targets to iSCSI by default. Either dynamic or static mapping must be configured before the IPS module makes FC targets available to iSCSI initiators. When both are configured, statically mapped FC targets have a configured name. In this configuration you will see an example of static mapping. With dynamic mapping, each time the iSCSI host connects to the IPS module a new FC N port is created and the nWWNs and pWWNs allocated for this N port may be different. Use the static mapping method if you need to obtain the same nWWNs and pWWNs for the iSCSI host each time it connects to the IPS module. Static mapping can be used on the IPS module to access intelligent FC storage arrays that have access control and LUN mapping/masking configuration based on the initiator's pWWNs and/or nWWNs.

    You can control access to each statically-mapped iSCSI target by specifying a list of IPS ports on which it will be advertised and specifying a list of iSCSI initiator node names allowed to access it. FC zoning-based access control and iSCSI-based access control are the two mechanisms by which access control can be provided for iSCSI. Both methods can be used simultaneously. In this configuration default zoning has been permitted for specific VSAN. IPS modules use both iSCSI node name-based and FC zoning-based access control lists to enforce access control during iSCSI discovery and iSCSI session creation.

    • iSCSI discovery: When an iSCSI host creates an iSCSI discovery session and queries for all iSCSI targets, the IPS module returns only the list of iSCSI targets this iSCSI host is allowed to access based on the access control policies.
    • iSCSI session creation: When an IP host initiates an iSCSI session, the IPS module verifies if the specified iSCSI target (in the session login request) is a static mapped target, and if true, verifies if the IP host's iSCSI node name is allowed to access the target. If the IP host does not have access, its login is rejected.
    The IP Storage module creates a FC virtual N port (the N port may already exist) for this IP host and does a FC name server query for the FCID of the FC target pWWN that is being accessed by the IP host. It uses the IP host virtual N port's pWWN as the requester of the name server query. Thus, the name server does a zone-enforced query for the pWWN and responds to the query. If the FCID is returned by the name server, then the iSCSI session is accepted. Otherwise, the login request is rejected.

    Configure

    In this section, you are presented with the information to configure the MDS 9216 and Cisco iSCSI Driver for Solaris.

    Note: To find additional information on the commands used in this document, use the Cisco MDS 9000 Family Command Reference and Cisco MDS 9000 Family Software Configuration Guide.

    Network Diagram

    This document uses the network setup shown in the diagram below.

    Configurations

    This document uses the configurations shown below.

    • Vuk (Windows Server 2003)

    • Canterbury (MDS 9216)

    Vuk (Windows Server 2003)
    The initial configuration tasks consist of the following actions:

    • Setting the iSCS Itarget IP addresses of MDS 9000 series systems that the driver will access.
    • Setting the iSCSI target authentication user name and passwords.
    • Saving the iSCSI target configuration, and setting the driver's boot type.
    To configure the driver, perform the following steps:

    1. Log on to the computer as a user with administrator privileges.

    2. Click Start, point to Settings, click Control Panel and then double click iSCSI Config.

      The Iscsi Config program causes the Cisco iSCSI config for Win 2000/XP/2003 dialog box to be displayed.

    3. At the Cisco iSCSI config for Win 2000 dialog box, configure the IP address of a SCSI routing instance in an MDS 9000 series system as follows:

      • At the Target Host Names/IP Addresses text box, type the IP address of a SCSI routing instance in an MDS 9000 Series system. In this configuration example, the IP address is 10.48.69.222.

      • Click Add. The IP address is displayed in the display area below the Target Host Names/IP Addresses text box.

    4. Click Save and Exit.

    5. Restart the computer.

    Canterbury (Cisco MDS 9216)
    vsan database
    vsan 222 name ozden
    !---  VSAN 222 has been used for iSCSI targets.
    
    vsan database
    vsan 222 interface fc1/5 
    !--- Seagate is connected to fc1/5.
    vsan 222 interface fc1/6
    vsan 222 interface fc1/7 
    !--- IBM Shark is connected to fc1/7.
    vsan 222 interface fc1/8
    
    !--- System boot variables.
    boot system bootflash:/s121a
    boot kickstart bootflash:/k121a
    
    !--- IP configurations.
    ip domain-name cisco.com
    ip name-server 144.254.10.123
    ip default-gateway 10.48.69.129
    ip routing
    iscsi authentication none
    !--- Identify the iSCSI initiator based on the IP address of your host.
    !--- A static virtual N port is defined for each NIC or network interface.
    !--- LUN-mapping and LUN-masking on the storage device has to be done with the static pWWN
    !--- that you have defined for the initiator. Refer to the Enterprise Storage Server Specialist  
    !--- (ESSS) screen capture in the Fabric Manager and Device Manager Displays section
    !--- for more information.
    iscsi initiator ip-address 10.48.69.241
     static nWWN 22:01:00:0c:30:6c:24:42
     static pWWN 21:03:00:0c:30:6c:24:42
    !--- Targets via Vsan 222 are accesible by iSCSI initiators.
     vsan 222
    
    !--- A virtual target has been defined for the JBOD. The target has 
    !--- been identified by it's pWWN. The target has been advertised via
    !---  GE interface 2/5. Host 10.48.69.241 is the only initiator.
    iscsi virtual-target name seagate
     pWWN 21:00:00:04:cf:db:3e:a7 fc-lun 0x0000 iscsi-lun 0x0000
    advertise interface GigabitEthernet2/5
    initiator ip address 10.48.69.241 permit
    
    !--- A virtual target has been defined for the IBM Shark. The target has been identified by the pWWN.
    !--- Do not specify the LUN if you wish to map the entire FC target to an iSCSI target.
    !--- In the virtual-target shark-lun, LUN-mapping options have been used. FC-LUN 0x0000 has been
    !--- mapped to iSCSI-LUN 0x0000. It is also possible to map FC-LUN 0x0000 to a different iSCSI-LUN number.
    iscsi virtual-target name shark-lun
     pWWN 50:05:07:63:00:c4:94:4c fc-lun 0x0000 iscsi-lun 0x0000
     pWWN 50:05:07:63:00:c4:94:4c fc-lun 0x0001 iscsi-lun 0x0001
    advertise interface GigabitEthernet2/5
    initiator ip address 10.48.69.241 permit
    
    line console
     exec-timeout 0
    line vty
     exec-timeout 0
    ntp server 10.48.64.100
    
    switchname canterbury
    ..
    zone default-zone permit vsan 1
    !--- Default zone policy is set to permit for VSAN 222.
    zone default-zone permit vsan 222
    
    interface GigabitEthernet2/5
    ip address 10.48.69.222 255.255.255.192
    no shutdown
    ...
    interface fc1/5
    no shutdown
    
    interface fc1/6
    
    interface fc1/7
    no shutdown
    
    ...
    
    interface mgmt0
    ip address 10.48.69.156 255.255.255.192
    
    !---The iSCSI interface has to be set no shut.
    interface iscsi2/5
    no shutdown

    Verify

    This section provides information you can use to confirm your configuration is working properly.

    • show zone status - displays Zone information.

    • show fcns database vsan 222 - displays Name Server information for a specific VSAN.

    • show flogi database vsan 222 - displays FLOGI Server information for a specific VSAN.

    • show vsan membership - displays interface information for different VSANs.

    • show iscsi initiator detail - displays iSCSI initiator information.

    • show iscsi initiator iscsi-session detail - displays detailed information for iSCSI initiator session.

    • show iscsi initiator fcp-session detail - displays detailed information for iSCSI initiator FCP session.

    • show ips stats tcp interface gigabitethernet 2/5 detail - displays TCP statistics for specific GE interface.

    • show iscsi virtual-target configured - displays iSCSI virtual targets that has been configured on the MDS 9000.

    • show iscsi initiator configured - displays iSCSI initiators that have been configured on the MDS 9000.

    • show ips arp interface gigabitethernet 2/5 - displays IPS arp information for specific GE interface.

    • show scsi-target lun vsan 222 - displays SCSI devices for specific VSAN(for mapping FC-LUNs to iSCSI-LUNs).

    • show int iscsi 2/5 - displays iSCSI interfaces.

    • show iscsi stats iscsi 2/5 - displays iSCSI statistics.

    • show int gigabitethernet 2/5 - displays GE interface.

    • show ip route - displays IP route information.

    Troubleshoot

    This section provides information you can use to troubleshoot your configuration.

    Note: To find additional information on Troubleshooting IP Storage Issues, use the Cisco MDS 9000 Family Troubleshooting Guide.

    Troubleshooting Procedure

    Below is troubleshooting information relevant to this configuration.

    • Displays from Vuk (Windows Server 2003)

    • Displays from Canterbury Cisco MDS 9216


    Displays from Vuk (Windows Server 2003)

    On the Cisco iSCSI config window, click on Status to check if the host has successfully logged into the iSCSI targets. On the command line, issue netstat -an | find/i "established" to see ESTABLISHED TCP sesions between 10.48.69.222.

    To see the new disks, right click My Computer on the desktop. Double click on Computer Manager.

    In the console tree under System Tool, click Device Manager

    For the proper functioning of the driver under Windows 2003 Server, the driver needs to create a pseudo disk drive. This will show up as an unknown disk under the Disk Management MMC application. The user can ignore this, as it does not affect the performance or functioning of the system in any way. It must not be deleted.

    To manage the storage, right click My Computer on the desktop. Double click on Computer Manager.

    In the console tree under Storage, click Disk Management.


    Displays from Canterbury (Cisco MDS 9216)
    canterbury#show vsan membership
    vsan 1 interfaces:
     fc1/3 fc1/10 fc1/12 fc1/13 fc1/14 fc1/16
    
    vsan 222 interfaces:
     fc1/5 fc1/6 fc1/7 fc1/8
    
    vsan 4094(isolated_vsan) interfaces:
    
    canterbury#show zone status
    VSAN: 1 default-zone: permit distribute: active only Interop: 100
    Full Zoning Database :
     Zonesets:0 Zones:0 Aliases: 0
    Active Zoning Database :
     Database Not Available
    Status:
    
    VSAN: 222 default-zone: permit distribute: active only Interop: 100
    Full Zoning Database :
     Zonesets:0 Zones:0 Aliases: 0
    Active Zoning Database :
     Database Not Available
    Status:
    !--- VSAN 222 has been used for this configuration, default-zone behavior has been set to permit.
    canterbury#show flogi database vsan 222
    ---------------------------------------------------------------------------
    INTERFACE VSAN FCID PORT NAME NODE NAME
    ---------------------------------------------------------------------------
    fc1/5 222 0x62011e 21:00:00:04:cf:db:3e:a7 20:00:00:04:cf:db:3e:a7
    fc1/7 222 0x620003 50:05:07:63:00:c4:94:4c 50:05:07:63:00:c0:94:4c
    iscsi2/5 222 0x620001 21:03:00:0c:30:6c:24:42 22:01:00:0c:30:6c:24:42
    
    Total number of flogi = 3.
    !--- FCID 0X620001 is the virtual N port(HBA) for the iSCSI host Vuk.
    canterbury#show fcns database vsan 222
    
    VSAN 222:
    --------------------------------------------------------------------------
    FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
    --------------------------------------------------------------------------
    0x620001 N 21:03:00:0c:30:6c:24:42 (Cisco) scsi-fcp:init isc..w
    0x620003 N 50:05:07:63:00:c4:94:4c (IBM) scsi-fcp:target fc..
    0x62011e NL 21:00:00:04:cf:db:3e:a7 (Seagate) scsi-fcp:target
    
    Total number of entries = 3
    canterbury#show fcns database detail vsan 222
    ------------------------
    VSAN:222 FCID:0x620001
    ------------------------
    port-wwn (vendor) :21:03:00:0c:30:6c:24:42 (Cisco)
    node-wwn :22:01:00:0c:30:6c:24:42
    class :2,3
    node-ip-addr :10.48.69.241
    ipa :ff ff ff ff ff ff ff ff
    fc4-types:fc4_features:scsi-fcp:init iscsi-gw 
    !--- Virtual N port for host.
    symbolic-port-name :
    symbolic-node-name :10.48.69.241
    port-type :N
    port-ip-addr :0.0.0.0
    fabric-port-wwn :20:51:00:0c:30:6c:24:40
    hard-addr :0x000000
    ------------------------
    VSAN:222 FCID:0x620003
    ------------------------
    port-wwn (vendor) :50:05:07:63:00:c4:94:4c (IBM)
    node-wwn :50:05:07:63:00:c0:94:4c
    class :2,3
    node-ip-addr :0.0.0.0
    ipa :ff ff ff ff ff ff ff ff
    fc4-types:fc4_features:scsi-fcp:target fcsb2-ch-cu fcsb2-cu-ch
    symbolic-port-name :
    symbolic-node-name :
    port-type :N
    port-ip-addr :0.0.0.0
    fabric-port-wwn :20:07:00:0c:30:6c:24:40
    hard-addr :0x000000
    ------------------------
    VSAN:222 FCID:0x62011e
    ------------------------
    port-wwn (vendor) :21:00:00:04:cf:db:3e:a7 (Seagate)
    node-wwn :20:00:00:04:cf:db:3e:a7
    class :3
    node-ip-addr :0.0.0.0
    ipa :ff ff ff ff ff ff ff ff
    fc4-types:fc4_features:scsi-fcp:target
    symbolic-port-name :
    symbolic-node-name :
    port-type :NL
    port-ip-addr :0.0.0.0
    fabric-port-wwn :20:05:00:0c:30:6c:24:40
    hard-addr :0x000000
    
    Total number of entries = 3
    canterbury#show iscsi session
    Initiator 10.48.69.241
     Initiator name iqn.1987-05.com.cisco:02.9a74eb40e94d.vuk-win2003
     Session #1
     Discovery session, ISID 00023d000023, Status active
    
     Session #2
     Target shark-lun
     VSAN 222, ISID 00023d000024, Status active, no reservation
    
     Session #3
     Target seagate
     VSAN 222, ISID 00023d000025, Status active, no reservation
    
    canterbury#show iscsi initiator
    iSCSI Node name is 10.48.69.241
     iSCSI Initiator name: iqn.1987-05.com.cisco:02.9a74eb40e94d.vuk-win2003
     iSCSI alias name: VUK-WIN2003
     Node WWN is 22:01:00:0c:30:6c:24:42 (dynamic)
     Member of vsans: 222
     Number of Virtual n_ports: 1
     Virtual Port WWN is 21:03:00:0c:30:6c:24:42 (configured)
     Interface iSCSI 2/5, Portal group tag: 0x84
     VSAN ID 222, FCID 0x620001
    
    canterbury#show iscsi initiator detail
    iSCSI Node name is 10.48.69.241
     iSCSI Initiator name: iqn.1987-05.com.cisco:02.9a74eb40e94d.vuk-win2003
     iSCSI alias name: VUK-WIN2003
     Node WWN is 22:01:00:0c:30:6c:24:42 (dynamic)
     Member of vsans: 222
     Number of Virtual n_ports: 1
    
     Virtual Port WWN is 21:03:00:0c:30:6c:24:42 (configured)
     Interface iSCSI 2/5, Portal group tag is 0x84
     VSAN ID 222, FCID 0x620001
     2 FC sessions, 2 iSCSI sessions
     iSCSI session details
     Target: seagate
     Statistics:
     PDU: Command: 16, Response: 16
     Bytes: TX: 188, RX: 0
     Number of connection: 1
     TCP parameters
     Local 10.48.69.222:3260, Remote 10.48.69.241:1035
     Path MTU: 1500 bytes
     Retransmission timeout: 350 ms
     Round trip time: Smoothed 165 ms, Variance: 46
     Advertized window: Current: 125 KB, Maximum: 125 KB, Scale: 1
     Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
     Congestion window: Current: 9 KB
     Target: shark-lun
     Statistics:
     PDU: Command: 2343, Response: 2343
     Bytes: TX: 46363700, RX: 45494272
     Number of connection: 1
     TCP parameters
     Local 10.48.69.222:3260, Remote 10.48.69.241:1034
     Path MTU: 1500 bytes
     Retransmission timeout: 390 ms
     Round trip time: Smoothed 136 ms, Variance: 65
     Advertized window: Current: 125 KB, Maximum: 125 KB, Scale: 1
     Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
     Congestion window: Current: 11 KB
    
     FCP Session details
     Target FCID: 0x62011e (S_ID of this session: 0x620001)
     pWWN: 21:00:00:04:cf:db:3e:a7, nWWN: 20:00:00:04:cf:db:3e:a7
     Session state: LOGGED_IN
     1 iSCSI sessions share this FC session
     Target: seagate
     Negotiated parameters
     RcvDataFieldSize 1404 our_RcvDataFieldSize 1404
     MaxBurstSize 0, EMPD: FALSE
     Random Relative Offset: FALSE, Sequence-in-order: Yes
     Statistics:
     PDU: Command: 0, Response: 16
     Target FCID: 0x620003 (S_ID of this session: 0x620001)
     pWWN: 50:05:07:63:00:c4:94:4c, nWWN: 50:05:07:63:00:c0:94:4c
     Session state: LOGGED_IN
     1 iSCSI sessions share this FC session
     Target: shark-lun
     Negotiated parameters
     RcvDataFieldSize 2048 our_RcvDataFieldSize 1404
     MaxBurstSize 0, EMPD: FALSE
     Random Relative Offset: FALSE, Sequence-in-order: Yes
     Statistics:
     PDU: Command: 0, Response: 2343
    
    canterbury#show iscsi initiator iscsi-session detail
    iSCSI Node name is 10.48.69.241
     iSCSI Initiator name: iqn.1987-05.com.cisco:02.9a74eb40e94d.vuk-win2003
     iSCSI alias name: VUK-WIN2003
     Node WWN is 22:01:00:0c:30:6c:24:42 (dynamic)
     Member of vsans: 222
     Number of Virtual n_ports: 1
    
     Virtual Port WWN is 21:03:00:0c:30:6c:24:42 (configured)
     Interface iSCSI 2/5, Portal group tag is 0x84
     VSAN ID 222, FCID 0x620001
     2 FC sessions, 2 iSCSI sessions
     iSCSI session details
     Target: seagate
     Statistics:
     PDU: Command: 16, Response: 16
    
     Bytes: TX: 188, RX: 0
     Number of connection: 1
     TCP parameters
     Local 10.48.69.222:3260, Remote 10.48.69.241:1035
     Path MTU: 1500 bytes
     Retransmission timeout: 350 ms
     Round trip time: Smoothed 165 ms, Variance: 46
     Advertized window: Current: 125 KB, Maximum: 125 KB, Scale: 1
     Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
     Congestion window: Current: 9 KB
     Target: shark-lun
     Statistics:
     PDU: Command: 2343, Response: 2343
     Bytes: TX: 46363700, RX: 45494272
     Number of connection: 1
     TCP parameters
     Local 10.48.69.222:3260, Remote 10.48.69.241:1034
     Path MTU: 1500 bytes
     Retransmission timeout: 390 ms
     Round trip time: Smoothed 136 ms, Variance: 65
     Advertized window: Current: 125 KB, Maximum: 125 KB, Scale: 1
     Peer receive window: Current: 118 KB, Maximum: 118 KB, Scale: 1
     Congestion window: Current: 11 KB
    
    canterbury#show iscsi initiator fcp-session detail
    iSCSI Node name is 10.48.69.241
     iSCSI Initiator name: iqn.1987-05.com.cisco:02.9a74eb40e94d.vuk-win2003
     iSCSI alias name: VUK-WIN2003
     Node WWN is 22:01:00:0c:30:6c:24:42 (dynamic)
     Member of vsans: 222
     Number of Virtual n_ports: 1
    
     Virtual Port WWN is 21:03:00:0c:30:6c:24:42 (configured)
     Interface iSCSI 2/5, Portal group tag is 0x84
     VSAN ID 222, FCID 0x620001
     2 FC sessions, 2 iSCSI sessions
    
     FCP Session details
     Target FCID: 0x62011e (S_ID of this session: 0x620001)
     pWWN: 21:00:00:04:cf:db:3e:a7, nWWN: 20:00:00:04:cf:db:3e:a7
     Session state: LOGGED_IN
     1 iSCSI sessions share this FC session
     Target: seagate
     Negotiated parameters
     RcvDataFieldSize 1404 our_RcvDataFieldSize 1404
     MaxBurstSize 0, EMPD: FALSE
     Random Relative Offset: FALSE, Sequence-in-order: Yes
     Statistics:
     PDU: Command: 0, Response: 16
     Target FCID: 0x620003 (S_ID of this session: 0x620001)
     pWWN: 50:05:07:63:00:c4:94:4c, nWWN: 50:05:07:63:00:c0:94:4c
     Session state: LOGGED_IN
     1 iSCSI sessions share this FC session
     Target: shark-lun
     Negotiated parameters
     RcvDataFieldSize 2048 our_RcvDataFieldSize 1404
     MaxBurstSize 0, EMPD: FALSE
     Random Relative Offset: FALSE, Sequence-in-order: Yes
     Statistics:
     PDU: Command: 0, Response: 2343
    
    canterbury#show ips stats tcp interface gigabitethernet 2/5
    TCP Statistics for port GigabitEthernet2/5
     Connection Stats
     0 active openings, 345 accepts
     0 failed attempts, 0 reset received, 345 established
     Segment stats
     160524 received, 158647 sent, 1 retransmitted
     0 bad segments received, 1 reset sent
    
     TCP Active Connections
     Local Address Remote Address State Send-Q Recv-Q
     10.48.69.222:3260 10.48.69.241:1026 ESTABLISH 0 0
     10.48.69.222:3260 10.48.69.241:1034 ESTABLISH 0 0
     10.48.69.222:3260 10.48.69.241:1035 ESTABLISH 0 0
     0.0.0.0:3260 0.0.0.0:0 LISTEN 0 0
    canterbury#show ips stats tcp interface gigabitethernet 2/5 detail
    TCP Statistics for port GigabitEthernet2/5
     TCP send stats
     158647 segments, 132538432 bytes
     113573 data, 44411 ack only packets
     318 control (SYN/FIN/RST), 0 probes, 344 window updates
     1 segments retransmitted, 48 bytes
     1 retransmitted while on ethernet send queue, 0 packets split
     29286 delayed acks sent
     TCP receive stats
     160524 segments, 102518 data packets in sequence, 125344708 bytes in sequence
     0 predicted ack, 94889 predicted data
     0 bad checksum, 0 multi/broadcast, 0 bad offset
     0 no memory drops, 0 short segments
     0 duplicate bytes, 0 duplicate packets
     0 partial duplicate bytes, 0 partial duplicate packets
     0 out-of-order bytes, 0 out-of-order packets
     0 packet after window, 0 bytes after window
     0 packets after close
     58221 acks, 132539086 ack bytes, 0 ack toomuch, 6563 duplicate acks
     0 ack packets left of snd_una, 0 non-4 byte aligned packets
     37322 window updates, 0 window probe
     865 pcb hash miss, 171 no port, 1 bad SYN, 0 paws drops
     TCP Connection Stats
     0 attempts, 345 accepts, 345 established
     342 closed, 341 drops, 0 conn drops
     0 drop in retransmit timeout, 10 drop in keepalive timeout
     0 drop in persist drops, 0 connections drained
     TCP Miscellaneous Stats
     26399 segments timed, 26398 rtt updated
     1 retransmit timeout, 0 persist timeout
     6702 keepalive timeout, 6692 keepalive probes
     TCP SACK Stats
     0 recovery episodes, 0 data packets, 0 data bytes
     0 data packets retransmitted, 0 data bytes retransmitted
     0 connections closed, 0 retransmit timeouts
     TCP SYN Cache Stats
     345 entries, 345 connections completed, 0 entries timed out
     0 dropped due to overflow, 0 dropped due to RST
     0 dropped due to ICMP unreach, 0 dropped due to bucket overflow
     0 abort due to no memory, 0 duplicate SYN, 2 no-route SYN drop
     0 hash collisions, 0 retransmitted
    
     TCP Active Connections
     Local Address Remote Address State Send-Q Recv-Q
     10.48.69.222:3260 10.48.69.241:1026 ESTABLISH 0 0
     10.48.69.222:3260 10.48.69.241:1034 ESTABLISH 0 0
     10.48.69.222:3260 10.48.69.241:1035 ESTABLISH 0 0
     0.0.0.0:3260 0.0.0.0:0 LISTEN 0 0
    
    canterbury#show iscsi virtual-target configured
    target: seagate
     * Port WWN 21:00:00:04:cf:db:3e:a7 
    !--- The "*" means you have both discovery and target session. If there is no "*" in
    !--- front of the pWWN, it means either you only have discovery session or 
    !--- you have no active session.
     Configured node
     No. of LU mapping: 1
     iSCSI LUN: 0x0000, FC LUN: 0x0000
     No. of advertised interface: 1
     GigabitEthernet 2/5
     No. of initiators permitted: 1
     initiator 10.48.69.241/32 is permitted
     all initiator permit is disabled
    
    target: shark-lun
     * Port WWN 50:05:07:63:00:c4:94:4c
     Configured node
     No. of LU mapping: 2
     iSCSI LUN: 0x0000, FC LUN: 0x0000
     iSCSI LUN: 0x0001, FC LUN: 0x0001
     No. of advertised interface: 1
     GigabitEthernet 2/5
     No. of initiators permitted: 1
     initiator 10.48.69.241/32 is permitted
     all initiator permit is disabled
    
    canterbury#show iscsi initiator configured
    iSCSI Node name is 10.48.69.241
     Member of vsans: 222
     No. of PWWN: 1
     Port WWN is 21:03:00:0c:30:6c:24:42
    
    canterbury#show ips arp interface gigabitethernet 2/5
    Protocol Address Age (min) Hardware Addr Type Interface
    Internet 10.48.69.200 0 0008.e21e.c7bc ARPA GigabitEthernet2/5
    Internet 10.48.69.202 4 0202.3d30.45ca ARPA GigabitEthernet2/5
    Internet 10.48.69.206 4 0202.3d30.45ce ARPA GigabitEthernet2/5
    Internet 10.48.69.226 10 0060.08f6.bc1a ARPA GigabitEthernet2/5
    Internet 10.48.69.229 10 0800.209e.edab ARPA GigabitEthernet2/5
    Internet 10.48.69.232 5 0003.4796.34c3 ARPA GigabitEthernet2/5
    Internet 10.48.69.238 5 0030.6e1b.6f51 ARPA GigabitEthernet2/5
    Internet 10.48.69.239 11 0030.6e1c.a00b ARPA GigabitEthernet2/5
    Internet 10.48.69.241 4 000b.cdaf.b4c3 ARPA GigabitEthernet2/5
    Internet 10.48.69.248 2 0202.3d30.45f8 ARPA GigabitEthernet2/5
    Internet 10.10.2.28 5 0202.3d0a.021c ARPA GigabitEthernet2/5
    canterbury#show scsi-target devices vsan 222
    --------------------------------------------------------------------------------
    VSAN FCID PWWN VENDOR MODEL REV
    --------------------------------------------------------------------------------
    222 0x62011e 21:00:00:04:cf:db:3e:a7 SEAGATE ST336753FC 0003
    222 0x620003 50:05:07:63:00:c4:94:4c IBM 2105F20 .114
    
    !--- All LUNs that have been exported by the IBM Shark are not shown in the display output.
    canterbury#show scsi-target lun vsan 222
    
    - ST336753FC from SEAGATE (Rev 0003)
     FCID is 0x62011e in VSAN 222, PWWN is 21:00:00:04:cf:db:3e:a7
     ------------------------------------------------------------------------------
     LUN Capacity Status Serial Number Device-Id
     (MB)
     ------------------------------------------------------------------------------
    0x0 36704 Online 3HX00Q2600007326 C:1 A:0 T:3 20:00:00:04:cf:db:3e:a7
    
    - 2105F20 from IBM (Rev .114)
     FCID is 0x620003 in VSAN 222, PWWN is 50:05:07:63:00:c4:94:4c
     ------------------------------------------------------------------------------
     LUN Capacity Status Serial Number Device-Id
     (MB)
     ------------------------------------------------------------------------------
     0x5100 4000 Online 10022196 C:2 A:0 T:1 IBM 2105
    
     0x5101 4000 Online 10122196 C:2 A:0 T:1 IBM 2105
    
     ....
    
     0x5011 5000 Online 01122196 C:2 A:0 T:1 IBM 2105
    
    0x5012 5000 Online 01222196 C:2 A:0 T:1 IBM 2105
    
     0x5013 5000 Online 01322196 C:2 A:0 T:1 IBM 2105
    
     0x5014 5000 Online 01422196 C:2 A:0 T:1 IBM 2105
    
     0x5400 3000 Online 40022196 C:2 A:0 T:1 IBM 2105
    
     0x5401 5000 Online 40122196 C:2 A:0 T:1 IBM 2105
    
     0x5200 3000 Online 20022196 C:2 A:0 T:1 IBM 2105
    
     0x5201 3000 Online 20122196 C:2 A:0 T:1 IBM 2105
    
     0x5202 3000 Online 20222196 C:2 A:0 T:1 IBM 2105
    
     0x5203 3000 Online 20322196 C:2 A:0 T:1 IBM 2105
    
     0x5204 3000 Online 20422196 C:2 A:0 T:1 IBM 2105
    
     0x5205 3000 Online 20522196 C:2 A:0 T:1 IBM 2105
    
     0x5206 3000 Online 20622196 C:2 A:0 T:1 IBM 2105
    
     0x5207 3000 Online 20722196 C:2 A:0 T:1 IBM 2105
    
     0x5208 3000 Online 20822196 C:2 A:0 T:1 IBM 2105
    
    0x5209 3000 Online 20922196 C:2 A:0 T:1 IBM 2105
    
     .....
    
    canterbury#show int iscsi 2/5
    iscsi2/5 is up
     Hardware is GigabitEthernet
     Port WWN is 20:51:00:0c:30:6c:24:40
     Admin port mode is ISCSI
     Port mode is ISCSI
     Speed is 1 Gbps
     iSCSI initiator is identified by name
     Number of iSCSI session: 3, Number of TCP connection: 3
     Configured TCP parameters
     Local Port is 3260
     PMTU discover is enabled, reset timeout is 3600 sec
     Keepalive-timeout is 60 sec
     Minimum-retransmit-time is 300 ms
     Max-retransmissions 4
     Sack is disabled
     QOS code point is 0
     Forwarding mode: pass-thru
     TMF Queueing Mode : disabled
     5 minutes input rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
     5 minutes output rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
     iSCSI statistics
     Input 132567 packets, 125344708 bytes
     Command 8637 pdus, Data-out 117005 pdus, 118916096 bytes
     Output 113573 packets, 132538432 bytes
     Response 8439 pdus (with sense 10), R2T 3913 pdus
     Data-in 93902 pdus, 127070632 bytes
    
    
    canterbury#show iscsi stats iscsi 2/5
    iscsi2/5
     5 minutes input rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
     5 minutes output rate 16 bits/sec, 2 bytes/sec, 0 frames/sec
     iSCSI statistics
     132567 packets input, 125344708 bytes
     Command 8637 pdus, Data-out 117005 pdus, 118916096 bytes, 0 fragments
     output 113573 packets, 132538432 bytes
     Response 8439 pdus (with sense 10), R2T 3913 pdus
     Data-in 93902 pdus, 127070632 bytes
    
    canterbury#show int gigabitethernet 2/5
    GigabitEthernet2/5 is up
     Hardware is GigabitEthernet, address is 0005.3000.adea
     Internet address is 10.48.69.222/26
     MTU 1500 bytes
     Port mode is IPS
     Speed is 1 Gbps
     Beacon is turned off
     Auto-Negotiation is turned on
     5 minutes input rate 224 bits/sec, 28 bytes/sec, 0 frames/sec
     5 minutes output rate 80 bits/sec, 10 bytes/sec, 0 frames/sec
     205453 packets input, 138346789 bytes
     0 multicast frames, 0 compressed
     0 input errors, 0 frame, 0 overrun 0 fifo
     165673 packets output, 141485482 bytes, 0 underruns
     0 output errors, 0 collisions, 0 fifo
     0 carrier errors
    
    canterbury#show ip route
    
    Codes: C - connected, S - static
    
    Gateway of last resort is 10.48.69.129
    
    C 10.48.69.192/26 is directly connected, GigabitEthernet2/5
    C 10.48.69.128/26 is directly connected, mgmt0
    canterbury#

    Fabric Manager and Device Manager Displays

    This section provides screen captures from MDS Fabric Manager 1.2(2) and Device Manager 1.2(2).

    Topology diagram from the Fabric Manager

    Select FC-LUNs to display the pWWNs, LUN IDs, and the capacity of your LUNs from the Device Manager.

    Select FC-LUNs to display the Targets from the Device Manager.

    Select IP-iSCSI to display the iSCSI sessions from Device Manager.

    IBM Shark Definitions

    This section provides screen capture from Enterprise Storage Server Specialist (ESSS).

    One host has been defined on the ESS with static WWPN 21:03:00:0c:30:6c:24:42 that has been defined for initiator. Two volumes have been assigned to this host.


    Related Information


    Updated: Nov 29, 2005
    Document ID: 46060