Cisco VPN Client to VPN 3000 Concentrator with IPSec SDI Authentication (Server Version 3.3)
Available Languages
Contents
Introduction
The Cisco VPN 3000 Concentrator can be configured to authenticate Cisco VPN Clients through a Security Dynamics International (SDI) server. The VPN 3000 Concentrator acts as an SDI client, communicating with the SDI server on User Datagram Protocol (UDP) port 5500. The following document shows how to ensure that the SDI server, VPN 3000 Concentrator, and Cisco VPN Client are working properly, and then how to combine the components. If your VPN 3000 Concentrator has not yet been configured, use the steps from Install and Configure VPN 3000 Concentrator Without SDI using the command line interface (CLI) for the initial installation and configuration. If your VPN 3000 Concentrator has previously been configured, follow the steps for Modify Existing Configuration (Without SDI).
Prerequisites
Requirements
There are no specific prerequisites for this document.
Components Used
This configuration was developed and tested using the software and hardware versions below.
-
SDI server 3.3 (UNIX and NT)
-
VPN 3000 Concentrator (2.5.2)
-
VPN Client 2.5.2.A
The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Background Information
This document applies to both the Cisco VPN 3000 Client (2.5.x) or the Cisco VPN Client (3.x). With the release of 3.0 and later, you can now configure individual SDI servers for individual groups as opposed to one SDI server defined globally and used by all groups. Those groups that do not have individual SDI servers configured will use the SDI server defined globally.
There are three types of new personal identification number (PIN) modes in SDI. The VPN 3000 Concentrator supports the first two options as shown below.
-
User picks new PIN.
-
Server picks new PIN and informs users.
-
Server picks new PIN and informs users; users can change PIN.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
Network Diagram
This document uses the network setup shown in the diagram below.
Configurations
Install and Configure VPN 3000 Concentrator Without SDI
We configured the VPN 3000 Concentrator to locally authenticate a user in a group; by doing this before adding SDI, we could determine that IPSec between the Cisco VPN Client and VPN 3000 Concentrator is working. We cleared the VPN 3000 Concentrator configuration on the console port by going to Administration > System Reboot > Schedule reboot > Reboot with Factory/Default Configuration.
After rebooting, the following initial configuration was done:
| VPN 3000 Concentrator Concentrator Configuration |
|---|
Login: admin
Password:
Welcome to
Cisco Systems
VPN 3000 Concentrator Series
Command Line Interface
Copyright (C) 1998-2000 Cisco Systems, Inc.
-- : Set the time on your device. The correct time is very important,
-- : so that logging and accounting entries are accurate.
-- : Enter the system time in the following format:
-- : HH:MM:SS. Example 21:30:00 for 9:30 PM
> Time
Quick -> [ 13:02:39 ]
-- : Enter the date in the following format.
-- : MM/DD/YYYY Example 06/12/1999 for June 12th 1999.
> Date
Quick -> [ 10/09/2000 ]
-- : Set the time zone on your device. The correct time zone is very
-- : important so that logging and accounting entries are accurate.
-- : Enter the time zone using the hour offset from GMT:
-- : -12 : Kwajalein -11 : Samoa -10 : Hawaii -9 : Alaska
-- : -8 : PST -7 : MST -6 : CST -5 : EST
-- : -4 : Atlantic -3 : Brasilia -2 : Mid-Atlantic -1 : Azores
-- : 0 : GMT +1 : Paris +2 : Cairo +3 : Kuwait
-- : +4 : Abu Dhabi +5 : Karachi +6 : Almaty +7 : Bangkok
-- : +8 : Singapore +9 : Tokyo +10 : Sydney +11 : Solomon Is.
-- : +12 : Marshall Is.
> Time Zone
Quick -> [ -5 ] -5
1) Enable DST Support
2) Disable DST Support
Quick -> [ 1 ]
This table shows current IP addresses.
Interface IP Address/Subnet Mask MAC Address
-------------------------------------------------------------------------------
| Ethernet 1 - Private | 0.0.0.0/0.0.0.0 |
| Ethernet 2 - Public | 0.0.0.0/0.0.0.0 |
| Ethernet 3 - External | 0.0.0.0/0.0.0.0 |
-------------------------------------------------------------------------------
** An address is required for the private interface. **
> Enter IP Address
Quick Ethernet 1 -> [ 0.0.0.0 ] 10.31.1.59
Waiting for Network Initialization...
> Enter Subnet Mask
Quick Ethernet 1 -> [ 255.0.0.0 ] 255.255.255.0
1) Ethernet Speed 10 Mbps
2) Ethernet Speed 100 Mbps
3) Ethernet Speed 10/100 Mbps Auto Detect
Quick Ethernet 1 -> [ 3 ]
1) Enter Duplex - Half/Full/Auto
2) Enter Duplex - Full Duplex
3) Enter Duplex - Half Duplex
Quick Ethernet 1 -> [ 1 ]
1) Modify Ethernet 1 IP Address (Private)
2) Modify Ethernet 2 IP Address (Public)
3) Modify Ethernet 3 IP Address (External)
4) Configure Expansion Cards
5) Save changes to Config file
6) Continue
7) Exit
Quick -> 2
This table shows current IP addresses.
Interface IP Address/Subnet Mask MAC Address
-------------------------------------------------------------------------------
| Ethernet 1 - Private | 10.31.1.59/255.255.255.0 | 00.90.A4.00.1C.B4
| Ethernet 2 - Public | 0.0.0.0/0.0.0.0 |
| Ethernet 3 - External | 0.0.0.0/0.0.0.0 |
-------------------------------------------------------------------------------
> Enter IP Address
Quick Ethernet 2 -> [ 0.0.0.0 ] 172.18.124.134
> Enter Subnet Mask
Quick Ethernet 2 -> [ 255.255.0.0 ] 255.255.255.0
1) Ethernet Speed 10 Mbps
2) Ethernet Speed 100 Mbps
3) Ethernet Speed 10/100 Mbps Auto Detect
Quick Ethernet 2 -> [ 3 ]
1) Enter Duplex - Half/Full/Auto
2) Enter Duplex - Full Duplex
3) Enter Duplex - Half Duplex
Quick Ethernet 2 -> [ 1 ]
1) Modify Ethernet 1 IP Address (Private)
2) Modify Ethernet 2 IP Address (Public)
3) Modify Ethernet 3 IP Address (External)
4) Configure Expansion Cards
5) Save changes to Config file
6) Continue
7) Exit
Quick -> 6
-- : Assign a system name to this device.
> System Name
Quick -> vpn3000
-- : Specify a local DNS server, which lets you enter hostnames
-- : rather than IP addresses while configuring.
> DNS Server
Quick -> [ 0.0.0.0 ]
-- : Enter your Internet domain name; e.g., yourcompany.com
> Domain
Quick ->
> Default Gateway
Quick -> 172.18.124.1
-- : Configure protocols and encryption options.
-- : This table shows current protocol settings
PPTP | L2TP |
---------------------------------------------
| Enabled | Enabled |
| No Encryption Req | No Encryption Req |
---------------------------------------------
1) Enable PPTP
2) Disable PPTP
Quick -> [ 1 ]
1) PPTP Encryption Required
2) No Encryption Required
Quick -> [ 2 ]
1) Enable L2TP
2) Disable L2TP
Quick -> [ 1 ]
1) L2TP Encryption Required
2) No Encryption Required
Quick -> [ 2 ]
1) Enable IPSec
2) Disable IPSec
Quick -> [ 1 ]
-- : Configure address assignment for PPTP, L2TP and IPSec.
1) Enable Client Specified Address Assignment
2) Disable Client Specified Address Assignment
Quick -> [ 2 ]
1) Enable Per User Address Assignment
2) Disable Per User Address Assignment
Quick -> [ 2 ]
1) Enable DHCP Address Assignment
2) Disable DHCP Address Assignment
Quick -> [ 2 ]
1) Enable Configured Pool Address Assignment
2) Disable Configured Pool Address Assignment
Quick -> [ 2 ] 1
> Configured Pool Range Start Address
Quick -> 192.168.1.1
> Configured Pool Range End Address
Quick -> [ 0.0.0.0 ] 192.168.1.100
-- : Specify how to authenticate users
1) Internal Authentication Server
2) RADIUS Authentication Server
3) NT Domain Authentication Server
4) SDI Authentication Server
5) Continue
Quick -> [ 1 ] 1
Current Users
-------------------------------------------------------------------------------
No Users
-------------------------------------------------------------------------------
1) Add a User
2) Delete a User
3) Continue
Quick -> 1
> User Name
Quick -> 37297304
> Password
Quick -> *********
Verify -> *********
Current Users
-------------------------------------------------------------------------------
| 1. 37297304 | |
-------------------------------------------------------------------------------
1) Add a User
2) Delete a User
3) Continue
Quick -> 3
> IPSec Group Name
Quick -> vpn3000
> IPSec Group Password
Quick -> ********
Verify -> ********
-- : We strongly recommend that you change the password for user admin.
> Reset Admin Password
Quick -> [ ***** ]
Verify ->
1) Goto Main Configuration Menu
2) Save changes to Config file
3) Exit
Quick -> 2
1) Goto Main Configuration Menu
2) Save changes to Config file
3) Exit
Quick -> 3
Done
|
Modify Existing Configuration (Without SDI)
If the VPN 3000 Concentrator has previously been configured, the following screens are used to verify group, user, and IPSec/IKE settings:
-
Use this screen to add a group with local authentication:
-
Use this screen to add a user to the group with local authentication:
-
Use the IPSec > IKE proposal screen to add IKE settings (the settings shown are the system defaults):
Test Cisco VPN Client and VPN 3000 Concentrator Without SDI
After modifying the existing configuration on the VPN 3000 Concentrator, we install the Cisco VPN Client and configured a new connection to terminate at 172.18.124.134 (the public interface of concentrator). Our group access information was "vpn3000" (the name of the group) and the group password was the password for the group. When we clicked Connect, the username was "37297304" (name of user) and the user password was the password for the user (stored locally on the VPN 3000 Concentrator; no SDI is involved yet). See Good IPSec Debug With Local Authentication for the IKE, IKEDBG, IKEDECODE, IPSEC, IPSECDBG, IPSECDECODE debug.
Test SDI Server Operation Without VPN 3000 Concentrator
UNIX (Solaris)
-
On the SDI server, create an sditest account using the Solaris admintool.
The /etc/passwd entry should look like:
sditest:x:76:10::/local/0/sditest:/local/0/opt/ace/prog/sdshell
Note: Values and the paths to the user's home directory and "sdshell" depend on the system.
-
Assign a token to sditest.
-
Try Telnetting into the UNIX host as sditest. The host prompts you for a UNIX password and the PASSCODE. After authenticating, it lets you in as sditest in that host.
Microsoft Windows NT
-
Install the SecurSight Agent.
-
Select Programs > SecurSight > Test Authentication.
Configure SDI/User to Talk to VPN 3000 Concentrator
Use the following steps to configure SDI/User to talk to VPN 3000 Concentrator:
-
On the SDI Server Edit Token screen, verify that the token is "Enabled" and not in New PIN mode.
-
Click Resynchronize Token and Set PIN to Next Tokencode.
-
On the Edit User screen, assign a token to the user, and verify that "Allowed to create a PIN" is not checked.
-
Click Client Activations and verify that the VPN 3000 Concentrator is included.
Note: The VPN 3000 Concentrator is considered a client of the SDI server; the screen below is the SDI server Add/Edit Client screen. Because this is a new client, the "Sent Node Secret" box is grayed out. The SDI server has not had the opportunity to send the "node secret" file to the concentrator (this file would be displayed in the concentrator in Administration > File Management > Files section as "SECURID"). After a successful authentication from the VPN 3000, the "node secret" file is displayed on the VPN 3000 Concentrator and the "Sent Node Secret" box is checked.
-
Click User Activations and verify that the user is included.
Configure and Test VPN 3000 Concentrator to SDI
Use the following steps to configure and test VPN 3000 Concentrator to SDI.
-
Use the following screen to configure the VPN 3000 Concentrator to authenticate to SDI:
-
From SDI, go to Report > Log Monitor > Activity Monitor and click OK to observe incoming requests.
-
On the VPN 3000 Concentrator, click Test to test the connection.
-
If authentication is good, the VPN 3000 Concentrator displays:
Authentication Successful
In the above example, we defined one global SDI server. We can also choose to define individual SDI servers for each group by going to Configuration > User Management > Groups, highlighting the respective group, and choosing Modify Auth Server.
For debug information, refer to the following sections of this document:
Verify
This section provides information you can use to confirm your configuration is working properly.
Test Cisco VPN Client to VPN 3000 Concentrator with SDI
If everything works up to this point, it is time to combine the Cisco VPN Client, VPN 3000 Concentrator, and SDI server. We need to make one change on the VPN 3000 Concentrator by modifying the working group we called "vpn3000" to send requests to the SDI server.
Troubleshoot
This section provides information you can use to troubleshoot your configuration.
Turning on Debugging on the VPN 3000 Concentrator
Class Name for authentication:
-
AUTH
-
AUTHDBG
-
AUTHDECODE
Class Name for IPSec:
-
IKE, IKEDBG, IKEDECODE
-
IPSEC, IPSECDBG, IPSECDECODE
-
Severity to Log = 1-9
-
Severity to Console = 1-3
Click Get Log to view the results of the debug operation.
Good IPSec Debug With Local Authentication
1 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=1 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): 00 00 00 00 00 00 00 00
Next Payload : SA (1)
Exchange Type : Oakley Aggressive Mode
Flags : 0
Message ID : 0
Length : 307
7 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=1 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + NONE (0)
... total length : 307
10 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=2 161.44.17.135
processing SA payload
11 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=2 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 120
14 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=3 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ISAKMP (1)
#of Transforms: 4
Spi : 00 00 00 00
Length : 108
18 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=4 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : IKE (1)
Length : 24
20 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=5 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 1:
Encryption Alg: DES-CBC (1)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
24 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=6 161.44.17.135
Transform # 2 Decode for Proposal # 1:
Transform # : 2
Transform ID : IKE (1)
Length : 24
26 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=7 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 2:
Encryption Alg: Triple-DES (5)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
30 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=8 161.44.17.135
Transform # 3 Decode for Proposal # 1:
Transform # : 3
Transform ID : IKE (1)
Length : 24
32 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=9 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 3:
Encryption Alg: Triple-DES (5)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
36 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=10 161.44.17.135
Transform # 4 Decode for Proposal # 1:
Transform # : 4
Transform ID : IKE (1)
Length : 24
38 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=11 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 4:
Encryption Alg: DES-CBC (1)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
42 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=3 161.44.17.135
Proposal # 1, Transform # 1, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
47 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=4 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
50 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=5 161.44.17.135
Proposal # 1, Transform # 2, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
55 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=6 161.44.17.135
Proposal # 1, Transform # 3, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
60 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=7 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
62 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=8 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Encryption Alg:
Rcv'd: Triple-DES
Cfg'd: DES-CBC
65 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=9 161.44.17.135
Proposal # 1, Transform # 4, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
70 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=10 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
73 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=11 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
75 10/10/2000 17:12:32.560 SEV=7 IKEDBG/0 RPT=12 161.44.17.135
Oakley proposal is acceptable
76 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=13 161.44.17.135
processing ke payload
77 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=14 161.44.17.135
processing ISA_KE
78 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=1 161.44.17.135
processing nonce payload
79 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=2 161.44.17.135
Processing ID
80 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=3 161.44.17.135
processing vid payload
81 10/10/2000 17:12:32.580 SEV=9 IKEDBG/23 RPT=1 161.44.17.135
Starting group lookup for peer 161.44.17.135
82 10/10/2000 17:12:32.680 SEV=7 IKEDBG/0 RPT=15 161.44.17.135
Found Phase 1 Group (vpn3000)
83 10/10/2000 17:12:32.680 SEV=7 IKEDBG/14 RPT=1 161.44.17.135
Authentication configured for Internal
84 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=16 161.44.17.135
constructing ISA_SA for isakmp
85 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=17 161.44.17.135
constructing ke payload
86 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=4 161.44.17.135
constructing nonce payload
87 10/10/2000 17:12:32.680 SEV=9 IKE/0 RPT=1 161.44.17.135
Generating keys for Responder...
88 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=5 161.44.17.135
constructing ID
89 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=18
construct hash payload
90 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=19 161.44.17.135
computing hash
91 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=6 161.44.17.135
constructing vid payload
92 10/10/2000 17:12:32.680 SEV=8 IKEDBG/0 RPT=20 161.44.17.135
SENDING Message (msgid=0) with payloads :
HDR + SA (1) ... total length : 248
93 10/10/2000 17:12:32.730 SEV=8 IKEDECODE/0 RPT=12 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Aggressive Mode
Flags : 1 (ENCRYPT )
Message ID : 0
Length : 52
99 10/10/2000 17:12:32.730 SEV=8 IKEDBG/0 RPT=21 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
101 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=22 161.44.17.135
processing hash
102 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=23 161.44.17.135
computing hash
103 10/10/2000 17:12:33.410 SEV=8 IKEDECODE/0 RPT=13 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 308
110 10/10/2000 17:12:33.410 SEV=9 IKEDBG/21 RPT=1 161.44.17.135
Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress
111 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=24 161.44.17.135
constructing blank hash
112 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=25 161.44.17.135
constructing qm hash
113 10/10/2000 17:12:33.410 SEV=8 IKEDBG/0 RPT=26 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 68
115 10/10/2000 17:12:44.680 SEV=8 IKEDECODE/0 RPT=14 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 92
122 10/10/2000 17:12:44.680 SEV=8 IKEDBG/0 RPT=27 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 85
124 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=7
process_attr(): Enter!
125 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=8
Processing cfg reply attributes.
126 10/10/2000 17:12:44.980 SEV=7 IKEDBG/14 RPT=2 161.44.17.135
User [ 37297304 ]
Authentication configured for Internal
127 10/10/2000 17:12:44.980 SEV=4 IKE/52 RPT=7 161.44.17.135
User [ 37297304 ]
User (37297304) authenticated.
128 10/10/2000 17:12:44.980 SEV=9 IKEDBG/31 RPT=1 161.44.17.135
User [ 37297304 ]
Obtained IP addr (192.168.1.1) prior to initiating Mode Cfg (XAuth enabled)
130 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=28 161.44.17.135
User [ 37297304 ]
constructing blank hash
131 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=29 161.44.17.135
0000: 00010004 C0A80101 F0010000 ............
132 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=30 161.44.17.135
User [ 37297304 ]
constructing QM hash
133 10/10/2000 17:12:44.980 SEV=8 IKEDBG/0 RPT=31 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 80
135 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=15 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 68
142 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=32 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 64
144 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=9
process_attr(): Enter!
145 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=10
Processing cfg ACK attributes
146 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=11
Received IPV4 address ack!
147 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=12
Received Save PW ack!
148 10/10/2000 17:12:44.990 SEV=4 AUTH/21 RPT=18
User 37297304 connected
149 10/10/2000 17:12:44.990 SEV=7 IKEDBG/22 RPT=1 161.44.17.135
User [ 37297304 ]
Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed
151 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=33 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0)
... total length : 304
154 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=34 161.44.17.135
User [ 37297304 ]
processing hash
155 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=35 161.44.17.135
User [ 37297304 ]
processing SA payload
156 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=16 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 180
159 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=17 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
163 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=18 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
165 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=19 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
167 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=20 161.44.17.135
Proposal Decode:
Proposal # : 2
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
171 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=21 161.44.17.135
Transform # 1 Decode for Proposal # 2:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
173 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=22 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
175 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=23 161.44.17.135
Proposal Decode:
Proposal # : 3
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
179 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=24 161.44.17.135
Transform # 1 Decode for Proposal # 3:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
181 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=25 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
183 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=26 161.44.17.135
Proposal Decode:
Proposal # : 4
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
187 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=27 161.44.17.135
Transform # 1 Decode for Proposal # 4:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
189 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=28 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
191 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=29 161.44.17.135
Proposal Decode:
Proposal # : 5
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
195 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=30 161.44.17.135
Transform # 1 Decode for Proposal # 5:
Transform # : 1
Transform ID : NULL (11)
Length : 16
197 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=31 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
199 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=32 161.44.17.135
Proposal Decode:
Proposal # : 6
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
203 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=33 161.44.17.135
Transform # 1 Decode for Proposal # 6:
Transform # : 1
Transform ID : NULL (11)
Length : 16
205 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=34 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
207 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=13 161.44.17.135
User [ 37297304 ]
processing nonce payload
208 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=14 161.44.17.135
User [ 37297304 ]
Processing ID
209 10/10/2000 17:12:44.990 SEV=5 IKE/25 RPT=13 161.44.17.135
User [ 37297304 ]
Received remote Proxy Host data in ID Payload:
Address 161.44.17.135, Protocol 0, Port 0
212 10/10/2000 17:12:44.990 SEV=7 IKEDBG/1 RPT=15 161.44.17.135
User [ 37297304 ]
Modifying client proxy src address!
213 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=16 161.44.17.135
User [ 37297304 ]
Processing ID
214 10/10/2000 17:12:44.990 SEV=5 IKE/24 RPT=7 161.44.17.135
User [ 37297304 ]
Received local Proxy Host data in ID Payload:
Address 172.18.124.134, Protocol 0, Port 0
217 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=36 161.44.17.135
User [ 37297304 ]
Processing Notify payload
218 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=35 161.44.17.135
Notify Payload Decode :
DOI : IPSEC (1)
Protocol : ISAKMP (1)
Message : Initial contact (24578)
Spi : 9D F3 34 FE 89 BF AA B2 B7 AD 34 D2 74 4D 05 DA
Length : 28
224 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=37
QM IsRekeyed old sa not found by addr
225 10/10/2000 17:12:44.990 SEV=5 IKE/66 RPT=13 161.44.17.135
User [ 37297304 ]
IKE Remote Peer configured for SA: ESP-3DES-MD5
226 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=38 161.44.17.135
User [ 37297304 ]
processing IPSEC SA
227 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=39
Proposal # 1, Transform # 1, Type ESP, Id DES-CBC
Parsing received transform:
Phase 2 failure:
Mismatched transform IDs for protocol ESP:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
232 10/10/2000 17:12:45.000 SEV=7 IKEDBG/27 RPT=1 161.44.17.135
User [ 37297304 ]
IPSec SA Proposal # 2, Transform # 1 acceptable
233 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=40 161.44.17.135
User [ 37297304 ]
IKE: requesting SPI!
234 10/10/2000 17:12:45.000 SEV=6 IKE/0 RPT=2
AM received unexpected event EV_ACTIVATE_NEW_SA in state AM_ACTIVE
235 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/6 RPT=1
IPSEC key message parse - msgtype 6, len 164, vers 1, pid 00000000, seq 13,
err 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0,
hashKeyLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 300,
lifetime2 2000000000, dsId 2
239 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/1 RPT=1
Processing KEY_GETSPI msg!
240 10/10/2000 17:12:45.000 SEV=7 IPSECDBG/13 RPT=1
Reserved SPI 1773955517
241 10/10/2000 17:12:45.000 SEV=8 IKEDBG/6 RPT=1
IKE got SPI from key engine: SPI = 0x69bc69bd
242 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=41 161.44.17.135
User [ 37297304 ]
oakley constructing quick mode
243 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=42 161.44.17.135
User [ 37297304 ]
constructing blank hash
244 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=43 161.44.17.135
User [ 37297304 ]
constructing ISA_SA for ipsec
245 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=17 161.44.17.135
User [ 37297304 ]
constructing ipsec nonce payload
246 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=18 161.44.17.135
User [ 37297304 ]
constructing proxy ID
247 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=44 161.44.17.135
User [ 37297304 ]
Transmitting Proxy Id:
Remote host: 192.168.1.1 Protocol 0 Port 0
Local host: 172.18.124.134 Protocol 0 Port 0
251 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=45 161.44.17.135
User [ 37297304 ]
constructing QM hash
252 10/10/2000 17:12:45.000 SEV=8 IKEDBG/0 RPT=46 161.44.17.135
SENDING Message (msgid=48687ca1) with payloads :
HDR + HASH (8) ... total length : 136
254 10/10/2000 17:12:45.010 SEV=8 IKEDECODE/0 RPT=36 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 52
261 10/10/2000 17:12:45.010 SEV=8 IKEDBG/0 RPT=47 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
263 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=48 161.44.17.135
User [ 37297304 ]
processing hash
264 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=49 161.44.17.135
User [ 37297304 ]
loading all IPSEC SAs
265 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=19 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
266 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=20 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
267 10/10/2000 17:12:45.020 SEV=7 IKEDBG/0 RPT=50 161.44.17.135
User [ 37297304 ]
Loading host:
Dst: 172.18.124.134
Src: 192.168.1.1
268 10/10/2000 17:12:45.020 SEV=4 IKE/49 RPT=13 161.44.17.135
User [ 37297304 ]
Security negotiation complete for User (37297304)
Responder, Inbound SPI = 0x69bc69bd, Outbound SPI = 0x991518b4
271 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=2
IPSEC key message parse - msgtype 1, Len 536, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 64, label 0, pad 0, spi 991518b4, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
274 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=2
Processing KEY_ADD MSG!
275 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=3
key_msghdr2secassoc(): Enter
276 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=4
No USER filter configured
277 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=5
KeyProcessAdd: Enter
278 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=6
KeyProcessAdd: Adding outbound SA
279 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=7
KeyProcessAdd: src 172.18.124.134 mask 0.0.0.0, dst 192.168.1.1 mask 0.0.0.0
280 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=8
KeyProcessAdd: FilterIpsecAddIkeSa success
281 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=3
IPSEC key message parse - msgtype 3, Len 292, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 32, label 0, pad 0, spi 69bc69bd, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
284 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=9
Processing KEY_UPDATE MSG!
285 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=10
Update inbound SA addresses
286 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=11
key_msghdr2secassoc(): Enter
287 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=12
No USER filter configured
288 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=13
KeyProcessUpdate: Enter
289 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=14
KeyProcessUpdate: success
290 10/10/2000 17:12:45.020 SEV=8 IKEDBG/7 RPT=1
IKE got a KEY_ADD MSG for SA: SPI = 0x991518b4
291 10/10/2000 17:12:45.020 SEV=8 IKEDBG/0 RPT=51
pitcher: rcv KEY_UPDATE, spi 0x69bc69bd
Good IPSec Debug With Local Authentication
1 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=1 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): 00 00 00 00 00 00 00 00
Next Payload : SA (1)
Exchange Type : Oakley Aggressive Mode
Flags : 0
Message ID : 0
Length : 307
7 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=1 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + NONE (0)
... total length : 307
10 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=2 161.44.17.135
processing SA payload
11 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=2 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 120
14 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=3 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ISAKMP (1)
#of Transforms: 4
Spi : 00 00 00 00
Length : 108
18 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=4 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : IKE (1)
Length : 24
20 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=5 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 1:
Encryption Alg: DES-CBC (1)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
24 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=6 161.44.17.135
Transform # 2 Decode for Proposal # 1:
Transform # : 2
Transform ID : IKE (1)
Length : 24
26 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=7 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 2:
Encryption Alg: Triple-DES (5)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
30 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=8 161.44.17.135
Transform # 3 Decode for Proposal # 1:
Transform # : 3
Transform ID : IKE (1)
Length : 24
32 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=9 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 3:
Encryption Alg: Triple-DES (5)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
36 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=10 161.44.17.135
Transform # 4 Decode for Proposal # 1:
Transform # : 4
Transform ID : IKE (1)
Length : 24
38 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=11 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 4:
Encryption Alg: DES-CBC (1)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
42 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=3 161.44.17.135
Proposal # 1, Transform # 1, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
47 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=4 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
50 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=5 161.44.17.135
Proposal # 1, Transform # 2, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
55 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=6 161.44.17.135
Proposal # 1, Transform # 3, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
60 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=7 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
62 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=8 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Encryption Alg:
Rcv'd: Triple-DES
Cfg'd: DES-CBC
65 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=9 161.44.17.135
Proposal # 1, Transform # 4, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
70 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=10 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
73 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=11 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
75 10/10/2000 17:12:32.560 SEV=7 IKEDBG/0 RPT=12 161.44.17.135
Oakley proposal is acceptable
76 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=13 161.44.17.135
processing ke payload
77 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=14 161.44.17.135
processing ISA_KE
78 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=1 161.44.17.135
processing nonce payload
79 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=2 161.44.17.135
Processing ID
80 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=3 161.44.17.135
processing vid payload
81 10/10/2000 17:12:32.580 SEV=9 IKEDBG/23 RPT=1 161.44.17.135
Starting group lookup for peer 161.44.17.135
82 10/10/2000 17:12:32.680 SEV=7 IKEDBG/0 RPT=15 161.44.17.135
Found Phase 1 Group (vpn3000)
83 10/10/2000 17:12:32.680 SEV=7 IKEDBG/14 RPT=1 161.44.17.135
Authentication configured for Internal
84 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=16 161.44.17.135
constructing ISA_SA for isakmp
85 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=17 161.44.17.135
constructing ke payload
86 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=4 161.44.17.135
constructing nonce payload
87 10/10/2000 17:12:32.680 SEV=9 IKE/0 RPT=1 161.44.17.135
Generating keys for Responder...
88 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=5 161.44.17.135
constructing ID
89 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=18
construct hash payload
90 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=19 161.44.17.135
computing hash
91 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=6 161.44.17.135
constructing vid payload
92 10/10/2000 17:12:32.680 SEV=8 IKEDBG/0 RPT=20 161.44.17.135
SENDING Message (msgid=0) with payloads :
HDR + SA (1) ... total length : 248
93 10/10/2000 17:12:32.730 SEV=8 IKEDECODE/0 RPT=12 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Aggressive Mode
Flags : 1 (ENCRYPT )
Message ID : 0
Length : 52
99 10/10/2000 17:12:32.730 SEV=8 IKEDBG/0 RPT=21 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
101 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=22 161.44.17.135
processing hash
102 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=23 161.44.17.135
computing hash
103 10/10/2000 17:12:33.410 SEV=8 IKEDECODE/0 RPT=13 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 308
110 10/10/2000 17:12:33.410 SEV=9 IKEDBG/21 RPT=1 161.44.17.135
Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress
111 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=24 161.44.17.135
constructing blank hash
112 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=25 161.44.17.135
constructing qm hash
113 10/10/2000 17:12:33.410 SEV=8 IKEDBG/0 RPT=26 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 68
115 10/10/2000 17:12:44.680 SEV=8 IKEDECODE/0 RPT=14 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 92
122 10/10/2000 17:12:44.680 SEV=8 IKEDBG/0 RPT=27 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 85
124 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=7
process_attr(): Enter!
125 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=8
Processing cfg reply attributes.
126 10/10/2000 17:12:44.980 SEV=7 IKEDBG/14 RPT=2 161.44.17.135
User [ 37297304 ]
Authentication configured for Internal
127 10/10/2000 17:12:44.980 SEV=4 IKE/52 RPT=7 161.44.17.135
User [ 37297304 ]
User (37297304) authenticated.
128 10/10/2000 17:12:44.980 SEV=9 IKEDBG/31 RPT=1 161.44.17.135
User [ 37297304 ]
Obtained IP addr (192.168.1.1) prior to initiating Mode Cfg (XAuth enabled)
130 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=28 161.44.17.135
User [ 37297304 ]
constructing blank hash
131 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=29 161.44.17.135
0000: 00010004 C0A80101 F0010000 ............
132 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=30 161.44.17.135
User [ 37297304 ]
constructing QM hash
133 10/10/2000 17:12:44.980 SEV=8 IKEDBG/0 RPT=31 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 80
135 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=15 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 68
142 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=32 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 64
144 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=9
process_attr(): Enter!
145 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=10
Processing cfg ACK attributes
146 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=11
Received IPV4 address ack!
147 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=12
Received Save PW ack!
148 10/10/2000 17:12:44.990 SEV=4 AUTH/21 RPT=18
User 37297304 connected
149 10/10/2000 17:12:44.990 SEV=7 IKEDBG/22 RPT=1 161.44.17.135
User [ 37297304 ]
Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed
151 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=33 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0)
... total length : 304
154 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=34 161.44.17.135
User [ 37297304 ]
processing hash
155 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=35 161.44.17.135
User [ 37297304 ]
processing SA payload
156 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=16 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 180
159 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=17 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
163 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=18 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
165 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=19 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
167 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=20 161.44.17.135
Proposal Decode:
Proposal # : 2
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
171 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=21 161.44.17.135
Transform # 1 Decode for Proposal # 2:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
173 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=22 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
175 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=23 161.44.17.135
Proposal Decode:
Proposal # : 3
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
179 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=24 161.44.17.135
Transform # 1 Decode for Proposal # 3:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
181 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=25 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
183 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=26 161.44.17.135
Proposal Decode:
Proposal # : 4
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
187 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=27 161.44.17.135
Transform # 1 Decode for Proposal # 4:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
189 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=28 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
191 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=29 161.44.17.135
Proposal Decode:
Proposal # : 5
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
195 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=30 161.44.17.135
Transform # 1 Decode for Proposal # 5:
Transform # : 1
Transform ID : NULL (11)
Length : 16
197 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=31 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
199 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=32 161.44.17.135
Proposal Decode:
Proposal # : 6
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
203 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=33 161.44.17.135
Transform # 1 Decode for Proposal # 6:
Transform # : 1
Transform ID : NULL (11)
Length : 16
205 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=34 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
207 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=13 161.44.17.135
User [ 37297304 ]
processing nonce payload
208 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=14 161.44.17.135
User [ 37297304 ]
Processing ID
209 10/10/2000 17:12:44.990 SEV=5 IKE/25 RPT=13 161.44.17.135
User [ 37297304 ]
Received remote Proxy Host data in ID Payload:
Address 161.44.17.135, Protocol 0, Port 0
212 10/10/2000 17:12:44.990 SEV=7 IKEDBG/1 RPT=15 161.44.17.135
User [ 37297304 ]
Modifying client proxy src address!
213 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=16 161.44.17.135
User [ 37297304 ]
Processing ID
214 10/10/2000 17:12:44.990 SEV=5 IKE/24 RPT=7 161.44.17.135
User [ 37297304 ]
Received local Proxy Host data in ID Payload:
Address 172.18.124.134, Protocol 0, Port 0
217 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=36 161.44.17.135
User [ 37297304 ]
Processing Notify payload
218 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=35 161.44.17.135
Notify Payload Decode :
DOI : IPSEC (1)
Protocol : ISAKMP (1)
Message : Initial contact (24578)
Spi : 9D F3 34 FE 89 BF AA B2 B7 AD 34 D2 74 4D 05 DA
Length : 28
224 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=37
QM IsRekeyed old sa not found by addr
225 10/10/2000 17:12:44.990 SEV=5 IKE/66 RPT=13 161.44.17.135
User [ 37297304 ]
IKE Remote Peer configured for SA: ESP-3DES-MD5
226 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=38 161.44.17.135
User [ 37297304 ]
processing IPSEC SA
227 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=39
Proposal # 1, Transform # 1, Type ESP, Id DES-CBC
Parsing received transform:
Phase 2 failure:
Mismatched transform IDs for protocol ESP:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
232 10/10/2000 17:12:45.000 SEV=7 IKEDBG/27 RPT=1 161.44.17.135
User [ 37297304 ]
IPSec SA Proposal # 2, Transform # 1 acceptable
233 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=40 161.44.17.135
User [ 37297304 ]
IKE: requesting SPI!
234 10/10/2000 17:12:45.000 SEV=6 IKE/0 RPT=2
AM received unexpected event EV_ACTIVATE_NEW_SA in state AM_ACTIVE
235 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/6 RPT=1
IPSEC key message parse - msgtype 6, len 164, vers 1, pid 00000000, seq 13,
err 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0,
hashKeyLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 300,
lifetime2 2000000000, dsId 2
239 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/1 RPT=1
Processing KEY_GETSPI msg!
240 10/10/2000 17:12:45.000 SEV=7 IPSECDBG/13 RPT=1
Reserved SPI 1773955517
241 10/10/2000 17:12:45.000 SEV=8 IKEDBG/6 RPT=1
IKE got SPI from key engine: SPI = 0x69bc69bd
242 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=41 161.44.17.135
User [ 37297304 ]
oakley constructing quick mode
243 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=42 161.44.17.135
User [ 37297304 ]
constructing blank hash
244 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=43 161.44.17.135
User [ 37297304 ]
constructing ISA_SA for ipsec
245 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=17 161.44.17.135
User [ 37297304 ]
constructing ipsec nonce payload
246 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=18 161.44.17.135
User [ 37297304 ]
constructing proxy ID
247 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=44 161.44.17.135
User [ 37297304 ]
Transmitting Proxy Id:
Remote host: 192.168.1.1 Protocol 0 Port 0
Local host: 172.18.124.134 Protocol 0 Port 0
251 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=45 161.44.17.135
User [ 37297304 ]
constructing QM hash
252 10/10/2000 17:12:45.000 SEV=8 IKEDBG/0 RPT=46 161.44.17.135
SENDING Message (msgid=48687ca1) with payloads :
HDR + HASH (8) ... total length : 136
254 10/10/2000 17:12:45.010 SEV=8 IKEDECODE/0 RPT=36 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 52
261 10/10/2000 17:12:45.010 SEV=8 IKEDBG/0 RPT=47 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
263 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=48 161.44.17.135
User [ 37297304 ]
processing hash
264 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=49 161.44.17.135
User [ 37297304 ]
loading all IPSEC SAs
265 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=19 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
266 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=20 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
267 10/10/2000 17:12:45.020 SEV=7 IKEDBG/0 RPT=50 161.44.17.135
User [ 37297304 ]
Loading host:
Dst: 172.18.124.134
Src: 192.168.1.1
268 10/10/2000 17:12:45.020 SEV=4 IKE/49 RPT=13 161.44.17.135
User [ 37297304 ]
Security negotiation complete for User (37297304)
Responder, Inbound SPI = 0x69bc69bd, Outbound SPI = 0x991518b4
271 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=2
IPSEC key message parse - msgtype 1, Len 536, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 64, label 0, pad 0, spi 991518b4, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
274 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=2
Processing KEY_ADD MSG!
275 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=3
key_msghdr2secassoc(): Enter
276 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=4
No USER filter configured
277 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=5
KeyProcessAdd: Enter
278 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=6
KeyProcessAdd: Adding outbound SA
279 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=7
KeyProcessAdd: src 172.18.124.134 mask 0.0.0.0, dst 192.168.1.1 mask 0.0.0.0
280 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=8
KeyProcessAdd: FilterIpsecAddIkeSa success
281 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=3
IPSEC key message parse - msgtype 3, Len 292, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 32, label 0, pad 0, spi 69bc69bd, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
284 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=9
Processing KEY_UPDATE MSG!
285 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=10
Update inbound SA addresses
286 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=11
key_msghdr2secassoc(): Enter
287 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=12
No USER filter configured
288 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=13
KeyProcessUpdate: Enter
289 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=14
KeyProcessUpdate: success
290 10/10/2000 17:12:45.020 SEV=8 IKEDBG/7 RPT=1
IKE got a KEY_ADD MSG for SA: SPI = 0x991518b4
291 10/10/2000 17:12:45.020 SEV=8 IKEDBG/0 RPT=51
pitcher: rcv KEY_UPDATE, spi 0x69bc69bd
Good Debug With SDI
SDI Debug
If successful (first authentication on SDI)
10/06/2000 11:57:04/U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 11:57:04/L Node Secret Sent to Client zekie.cisco.com 10/06/2000 15:57:05/U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 11:57:05/U PASSCODE Accepted zekie.cisco.com
If successful (after the first authentication on SDI)
10/06/2000 16:06:09U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 12:06:09L PASSCODE Accepted zekie.cisco.com
VPN 3000 Concentrator Debug (on test)
Debug "Class Name" for authentication:
-
AUTH
-
AUTHDBG
-
AUTHDECODE
4 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/1 RPT=1 AUTH_Open() returns 14 5 10/06/2000 14:09:25.000 SEV=7 AUTH/12 RPT=1 Authentication session opened: handle = 14 6 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/3 RPT=1 AUTH_PutAttrTable(14, 5a2aa0) 7 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/5 RPT=1 AUTH_Authenticate(14, e5187e0, 306bdc) 8 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/59 RPT=1 AUTH_BindServer(71e097c, 0, 0) 9 10/06/2000 14:09:25.000 SEV=9 AUTHDBG/69 RPT=1 Auth Server 649ab4 has been bound to ACB 71e097c, sessions = 1 10 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/65 RPT=1 AUTH_CreateTimer(71e097c, 0, 0) 11 10/06/2000 14:09:25.000 SEV=9 AUTHDBG/72 RPT=1 Reply timer created: handle = 490011 12 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/61 RPT=1 AUTH_BuildMsg(71e097c, 0, 0) 13 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/51 RPT=1 Sdi_Build(71e097c) 14 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/64 RPT=1 AUTH_StartTimer(71e097c, 0, 0) 15 10/06/2000 14:09:25.010 SEV=9 AUTHDBG/73 RPT=1 Reply timer started: handle = 490011, timestamp = 8553930, timeout = 4000 16 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/62 RPT=1 AUTH_SndRequest(71e097c, 0, 0) 17 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/52 RPT=1 Sdi_Xmt(71e097c) 18 10/06/2000 14:09:25.010 SEV=9 AUTHDBG/71 RPT=1 xmit_cnt = 1 19 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/63 RPT=1 AUTH_RcvReply(71e097c, 0, 0) 20 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/53 RPT=1 Sdi_Rcv(71e097c) 21 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/66 RPT=1 AUTH_DeleteTimer(71e097c, 0, 0) 22 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/74 RPT=1 Reply timer stopped: handle = 490011, timestamp = 8554037 23 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/58 RPT=1 AUTH_Callback(71e097c, 0, 0) 24 10/06/2000 14:09:26.080 SEV=6 AUTH/4 RPT=1 Authentication successful: handle = 14, server = 172.18.124.99, user = 37297304 25 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/2 RPT=1 AUTH_Close(14) 26 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/60 RPT=1 AUTH_UnbindServer(71e097c, 0, 0) 27 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/70 RPT=1 Auth Server 649ab4 has been unbound from ACB 71e097c, sessions = 0 28 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/10 RPT=1 AUTH_Int_FreeAuthCB(71e097c) 29 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/19 RPT=1 instance = 15, clone_instance = 0 30 10/06/2000 14:09:26.080 SEV=7 AUTH/13 RPT=1 Authentication session closed: handle = 14
Bad Debugs
Bad username or user not activated on client
SDI debug
10/06/2000 16:30:21U junk/vpn3000 10/06/2000 12:30:21L User Not on Client zekie.cisco.com
VPN 3000 debug
21 10/06/2000 14:20:06.310 SEV=3 AUTH/5 RPT=5 Authentication rejected: Reason = Unspecified handle = 15, server = 172.18.124.99, user = junk
Good username, bad passcode
SDI debug
10/06/2000 16:33:07U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 12:33:07L ACCESS DENIED, PASSCODE Incorrect zekie.cisco.com
VPN 3000 debug
249 10/06/2000 14:22:52.160 SEV=3 AUTH/5 RPT=6 Authentication rejected: Reason = Unspecified handle = 16, server = 172.18.124.99, user = 37297304
SDI Server unreachable or daemon down
SDI debug
Shows nothing (did not receive request)
VPN 3000 debug
77 10/06/2000 14:28:55.600 SEV=4 AUTH/9 RPT=7 Authentication failed: Reason = Network error handle = 17, server = 172.18.124.99, user = 37297304
VPN 3000 not configured as client on SDI box
SDI debug
10/06/2000 17:37:42U --/172.18.124.134 -->/ 10/06/2000 13:36:42L Client Not Found zekie.cisco.com
VPN 3000 debug
113 10/06/2000 15:26:27.440 SEV=3 AUTH/5 RPT=8 Authentication rejected: Reason = Unspecified handle = 21, server = 172.18.124.99, user = 37297304
Removed VPN 3000 Concentrator as a client from the SDI server, then re-added it
The SDI server tried to send down the SECURID file to replace the old one, but the VPN 3000 already had this file.
Message on SDI
10/06/2000 13:42:18L Node Verification Failed zekie.cisco.com
VPN 3000 debug
21 10/06/2000 15:32:03.030 SEV=3 AUTH/5 RPT=9 Authentication rejected: Reason = Unspecified handle = 22, server = 172.18.124.99, user = 37297304
To resolve this problem, delete the SECURID file on the VPN 3000 Concentrator by going to Administration > File management > Files > SECURID > Delete. On re-test, the VPN 3000 Concentrator accepts the new file from the SDI server. If Edit Client > Sent Node Secret check box is grayed out on the SDI, the SDI server was unable to complete the exchange. Once the VPN 3000 Concentrator has the SECURID file, the Sent Node Secret check box is checked/not grayed out.
Related Information
Revision History
| Revision | Publish Date | Comments |
|---|---|---|
1.0 |
14-Jan-2008 |
Initial Release |
FeedbackContact Cisco
- Open a Support Case
- (Requires a Cisco Service Contract)