Configuring an IPSec Tunnel - Cisco Secure PIX Firewall to Checkpoint 4.1 Firewall

Introduction

This sample configration demonstrates how to form an IPSec tunnel with pre-shared keys to join two private networks. In our example, the joined networks are the 192.168.1.X private network inside the Cisco Secure Pix Firewall (PIX) and the 10.32.50.X private network inside the Checkpoint. It is assumed that traffic from inside the PIX and inside the Checkpoint 4.1 Firewall to the Internet (represented here by the 172.18.124.X networks) flows prior to beginning this configuration.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these software and hardware versions:

• PIX Software version 5.3.1

• Checkpoint 4.1 Firewall

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to the Cisco Technical Tips Conventions for more information on document conventions.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .

Network Diagram

This document uses the network setup shown in this diagram:

Configurations

This document uses the configurations shown in this section.

PIX Version 5.3(1)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname cisco_endpoint
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
names
access-list 115 permit ip 192.168.1.0 255.255.255.0 
10.32.50.0 255.255.255.0 
access-list 115 deny ip 192.168.1.0 255.255.255.0 any 
pager lines 24
logging on
no logging timestamp
no logging standby
no logging console
logging monitor debugging
no logging buffered
logging trap debugging
no logging history
logging facility 20
logging queue 512
interface ethernet0 auto
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside 172.18.124.35 255.255.255.240
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
no failover
failover timeout 0:00:00
failover poll 15
failover ip address outside 0.0.0.0
failover ip address inside 0.0.0.0
arp timeout 14400
global (outside) 1 172.18.124.36
nat (inside) 0 access-list 115
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route outside 0.0.0.0 0.0.0.0 172.18.124.34 1
timeout xlate 3:00:00g SA 0x80bd6a10, conn_id = 0
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 
0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+ 
aaa-server RADIUS protocol radius 
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable

!--- IPSec configuration

sysopt connection permit-ipsec
no sysopt route dnat
crypto ipsec transform-set myset esp-des esp-sha-hmac 
crypto map rtpmap 10 ipsec-isakmp
crypto map rtpmap 10 match address 115
crypto map rtpmap 10 set peer 172.18.124.157 
crypto map rtpmap 10 set transform-set myset
crypto map rtpmap 10 set security-association lifetime seconds 
3600 kilobytes 4608000
crypto map rtpmap interface outside

!--- IKE configuration

isakmp enable outside
isakmp key ******** address 172.18.124.157 netmask 255.255.255.240 
isakmp identity address
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash sha
isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
telnet timeout 5
ssh timeout 5
terminal width 80
Cryptochecksum:dc43c44e4513d3633a3fc7b1c3802c79
: end
[OK] 

Checkpoint Firewall

1. Since the IKE and IPSec default lifetimes differ between vendors, select Properties > Encryption to set the Checkpoint lifetimes to agree with the PIX defaults.

   The PIX default IKE lifetime is 86400 seconds (=1440 minutes), modifiable by this command: isakmp policy # lifetime 86400

   The PIX IKE lifetime can be configured between 60-86400 seconds.

   The PIX default IPSec lifetime is 28800 seconds, modifiable by this command: crypto ipsec security-association lifetime seconds #

   You can configure a PIX IPSec lifetime between 120-86400 seconds.

   

2. Select Manage > Network objects > New (or Edit) > Network to configure the object for the internal ("cpinside") network behind the Checkpoint.

   This must agree with the destination (second) network in this PIX command: access-list 115 permit ip 192.168.1.0 255.255.255.0 10.32.50.0 255.255.255.0

   

3. Select Manage > Network objects > Edit to edit the object for the gateway ("RTPCPVPN" Checkpoint) endpoint that the PIX points to in this command: crypto map name # set peer ip_address

   Under Location, select Internal. For Type, select Gateway. Under Modules Installed, select the VPN-1 & FireWall-1 checkbox, and also select the Management Station checkbox:

   

4. Select Manage > Network objects > New > Network to configure the object for the external ("inside_cisco") network behind the PIX.

   This must agree with the source (first) network in this PIX command: access-list 115 permit ip 192.168.1.0 255.255.255.0 10.32.50.0 255.255.255.0

   

5. Select Manage > Network objects > New > Workstation to add an object for the external ("cisco_endpoint") PIX gateway. This is the PIX interface to which this command is applied: crypto map name interface outside

   Under Location, select External. For Type, select Gateway.

   Note: Do not select the VPN-1/FireWall-1 checkbox.

   

6. Select Manage > Network objects > Edit to edit the Checkpoint gateway endpoint (called "RTPCPVPN") VPN tab. Under Domain, select Other and then select the inside of the Checkpoint network (called "cpinside") from the drop-down list. Under Encryption schemes defined, select IKE, and then click Edit.

   

7. Change the IKE properties for DES encryption to agree with this command:

   isakmp policy # encryption des

8. Change the IKE properties to SHA1 hashing to agree with this command:

   isakmp policy # hash sha

   Change these settings:

   1. De-select Aggressive Mode.

   2. Select the Supports Subnets checkbox.

   3. Under Authentication Method, select the Pre-Shared Secret checkbox. This agrees with this command:

      isakmp policy # authentication pre-share

      

9. Click Edit Secrets to set the pre-shared key to agree with the PIX command:

   isakmp key key address address netmask netmask

   

10. Select Manage > Network Objects > Edit to edit the "cisco_endpoint" VPN tab. Under Domain, select Other, and then select the inside of the PIX network (called "inside_cisco"). Under Encryption schemes defined, select IKE, and then click Edit.

    

11. Change the IKE properties DES encryption to agree with this command:

    isakmp policy # encryption des

12. Change the IKE properties to SHA1 hashing to agree with this command:

    crypto isakmp policy # hash sha

    Change these settings:

    1. De-select Aggressive Mode.

    2. Select the Supports Subnets checkbox.

    3. Under Authentication Method, select the Pre-Shared Secret checkbox. This action agrees with this command:

       isakmp policy # authentication pre-share

       

13. Click Edit Secrets to set the pre-shared key to agree with this PIX command:

    isakmp key key address address netmask netmask

    

14. In the Policy Editor window, insert a rule with both Source and Destination as "inside_cisco" and "cpinside" (bidirectional). Set Service=Any, Action=Encrypt, and Track=Long.

    

15. Under the Action heading, click the green Encrypt icon and select Edit properties to configure encryption policies.

    

16. Select IKE, and then click Edit.

    

17. On the IKE Properties screen, change these properties to agree with the PIX IPSec transforms in this command:

    crypto ipsec transform-set myset esp-des esp-sha-hmac

    Under Transform, select Encryption + Data Integrity (ESP). The Encryption Algorithm must be DES, Data Integrity must be SHA1, and the Allowed Peer Gateway must be the external PIX gateway (called "cisco_endpoint"). Click OK.

    

18. After the Checkpoint is configured, select Policy > Install on the Checkpoint menu in order for the changes to take effect.

debug, show and clear Commands

This section provides information you can use to confirm your configuration is working properly.

Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.

Before you issue debug commands, refer to Important Information on Debug Commands.

Cisco PIX Firewall

• debug crypto engine—Display debug messages about crypto engines, which perform encryption and decryption.

• debug crypto isakmp—Display messages about IKE events.

• debug crypto ipsec—Display IPSec events.

• show crypto isakmp sa—View all current IKE security associations (SAs) at a peer.

• show crypto ipsec sa—View the settings used by current security associations.

• clear crypto isakmp sa—(from configuration mode) Clear all active IKE connections.

• clear crypto ipsec sa—(from configuration mode) Delete all IPSec security associations.

Checkpoint:

Because the Tracking was set for Long in the Policy Editor window shown in step 14, denied traffic appears in red in the Log Viewer. A more verbose debug can be obtained by entering:

C:\WINNT\FW1\4.1\fwstop
C:\WINNT\FW1\4.1\fw d -d

and in another window:

C:\WINNT\FW1\4.1\fwstart

Note: This was a Microsoft Windows NT installation.

You can clear SAs on the Checkpoint with these commands:

fw tab -t IKE_SA_table -x
fw tab -t ISAKMP_ESP_table -x
fw tab -t inbound_SPI -x
fw tab -t ISAKMP_AH_table -x

and answering yes at the Are you sure? prompt.

Troubleshoot

This section provides information you can use to troubleshoot your configuration.

Network Summarization

When mutliple adjacent inside networks are configured in the encryption domain on the Checkpoint, the device can automatically summarize them with regard to interesting traffic. If the crypto ACL on the PIX is not configured to match, the tunnel likely fails. For example, if the inside networks of 10.0.0.0 /24 and 10.0.1.0 /24 are configured to be included in the tunnel, they can be summarized to 10.0.0.0 /23.

Sample Debug Output from the PIX

cisco_endpoint# show debug
debug crypto ipsec 1
debug crypto isakmp 1
debug crypto engine
debug fover status
        tx      Off
        rx      Off
        open    Off
        cable   Off
        txdmp   Off
        rxdmp   Off
        ifc     Off
        rxip    Off
        txip    Off
        get     Off
        put     Off
        verify  Off
        switch  Off
        fail    Off
        fmsg    Off
cisco_endpoint# term mon
cisco_endpoint# 
ISAKMP (0): beginning Quick Mode exchange, 
M-ID of 2112882468:7df00724IPSEC(key_engine):
 got a queue event...
IPSEC(spi_response): getting spi 0x9d71f29c(2641490588) for SA 
        from  172.18.124.157 to   172.18.124.35 for prot 3
70
crypto_isakmp_process_block: src 172.18.124.157, dest 172.18.124.35
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 2112882468

ISAKMP : Checking IPSec proposal 1

ISAKMP: transform 1, ESP_DES
ISAKMP:   attributes in transform:
ISAKMP:      encaps is 1
ISAKMP:      SA life type in seconds
ISAKMP:      SA life duration (basic) of 28800
ISAKMP:      SA life type in kilobytes
ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0 
ISAKMP:      authenticator is HMAC-SHA
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): 
proposal part #1,
  (key eng. msg.) dest= 172.18.124.157, src= 172.18.124.35, 
    dest_proxy= 10.32.50.0/255.255.255.0/0/0 (type=4), 
    src_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-sha-hmac , 
    lifedur= 0s and 0kb, 
    spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4

ISAKMP (0): processing NONCE payload. message ID = 2112882468

ISAKMP (0): processing ID payload. message ID = 2112882468
ISAKMP (0): processing ID payload. message ID = 2112882468map_alloc_entry: 
allocating entry 3
map_alloc_entry: allocating entry 4

ISAKMP (0): Creating IPSec SAs
        inbound SA from  172.18.124.157 to   172.18.124.35 (proxy
      10.32.50.0 to 192.168.1.0)
        has spi 2641490588 and conn_id 3 and flags 4
        lifetime of 28800 seconds
        lifetime of 4608000 kilobytes
        outbound SA from   172.18.124.35 to  172.18.124.157 (proxy
     192.168.1.0 to 10.32.50.0)
        has spi 3955804195 and conn_id 4 and flags 4
        lifetime of 28800 seconds
        lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event...
IPSEC(initialize_sas): ,
  (key eng. msg.) dest= 172.18.124.35, src= 172.18.124.157, 
    dest_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    src_proxy= 10.32.50.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-sha-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0x9d71f29c(2641490588), conn_id= 3, keysize= 0, flags= 0x4
IPSEC(initialize_sas): ,
  (key eng. msg.) src= 172.18.124.35, dest= 172.18.124.157, 
    src_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), 
    dest_proxy= 10.32.50.0/255.255.255.0/0/0 (type=4),
    protocol= ESP, transform= esp-des esp-sha-hmac , 
    lifedur= 28800s and 4608000kb, 
    spi= 0xebc8c823(3955804195), conn_id= 4, keysize= 0, flags= 0x4

return status is IKMP_NO_ERROR2303: sa_request, (key eng. msg.) 
src= 172.18.124.35, dest= 172.18.124.157, 
src_proxy= 192.168.1.0/255.255.255.0/0/0 (type=4), dest_proxy= 
10.32.50.0/255.255.255.0/0/0 (type=4), 
protocol= ESP, 
transform= esp-des esp-sha-hmac , lifedur= 28800s and 4608000kb, 
spi= 0x0(0), conn_id= 0, keysize= 0, 
flags= 0x4004

602301: sa created, (sa) sa_dest= 172.18.124.35, sa_prot= 50, sa_spi= 
0x9d71f29c(2641490588), 
sa_trans= esp-des esp-sha-hmac , sa_conn_id= 3

602301: sa created, (sa) sa_dest= 172.18.124.157, sa_prot= 50, sa_spi= 
0xebc8c823(3955804195), 
sa_trans= esp-des esp-sha-hmac , sa_conn_id= 4

cisco_endpoint# sho cry ips sa

interface: outside
    Crypto map tag: rtpmap, local addr. 172.18.124.35

   local  ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
   current_peer: 172.18.124.157
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0, 
    #pkts decompress failed: 0 #send errors 0, #recv errors 0

     local crypto endpt.: 172.18.124.35, 
     remote crypto endpt.: 172.18.124.157
     path mtu 1500, ipsec overhead 0, media mtu 1500
     current outbound spi: 0

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   local  ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
   remote ident (addr/mask/prot/port): (10.32.50.0/255.255.255.0/0/0)
   current_peer: 172.18.124.157
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4
    #pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
    #send errors 1, #recv errors 0

   local crypto endpt.: 172.18.124.35, remote crypto endpt.: 172.18.124.157
     path mtu 1500, ipsec overhead 56, media mtu 1500
     current outbound spi: ebc8c823

     inbound esp sas:
      spi: 0x9d71f29c(2641490588)
        transform: esp-des esp-sha-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 3, crypto map: rtpmap
        sa timing: remaining key lifetime (k/sec): (4607999/28777)
        IV size: 8 bytes
        replay detection support: Y

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:
      spi: 0xebc8c823(3955804195)
        transform: esp-des esp-sha-hmac ,
        in use settings ={Tunnel, }
        slot: 0, conn id: 4, crypto map: rtpmap
        sa timing: remaining key lifetime (k/sec): (4607999/28777)
        IV size: 8 bytes
        replay detection support: Y

     outbound ah sas:

     outbound pcp sas:

cisco_endpoint# sho cry is sa
        dst            src         state     pending    created
  172.18.124.157   172.18.124.35    QM_IDLE        0           2

Related Information

• PIX Support Page
• PIX Command Reference
• Requests for Comments (RFCs)
• Configuring IPSec Network Security
• Configuring Internet Key Exchange Security Protocol
• PIX 5.2: Configuring IPSec
• PIX 5.3: Configuring IPSec
• IPSec Support Page
• Technical Support - Cisco Systems