Guest

Cisco 1602-R Ethernet/Serial Modular Router Cable Specifications

Cisco - Cisco 1602-R Ethernet/Serial Modular Router Cable Specifications

Document ID: 46784

Updated: Jul 07, 2005

   Print

Introduction

This document provides the cabling specifications for the Cisco 1602-R Ethernet/Serial Modular Router with 56K Data Service Unit (DSU).

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on the following hardware:

  • Cisco 1602-R Ethernet/Serial Modular Router with 56K DSU (4-wire)

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, see the Cisco Technical Tips Conventions.

Cable Specifications

The 1602-R Ethernet/Serial Modular Router has one Ethernet interface, one Serial interface with 56 K Data Service Unit (DSU) (4-wire), and one WAN interface card (WIC) slot.

1602R.gif

The cabling specifications for the Cisco 1602-R are as follows:

Console

The console cable is an RJ-45, the CAB-1600-CON=.

Ethernet Interface

On the 1602-R router, there is one functional port for either the 10Base-T (RJ-45)or the AUI (DB-15). The cable details are: CAB-ETH-S-RJ45= Yellow cable for Ethernet, Straight-through, RJ-45, 6 ft.

Serial Interface

The Serial interface is a 56 K, 4-wire data service unit/channel service unit (DSU/CSU) for an RJ-45 cable. The telco RJ45 designation is the same as the RJ-48S.

The cable details are: CAB-DSU-RJ45= Blue Color Cable for DSU/CSU, RJ-45, 6 ft.

The table below lists the pin layout of the 56-kbps DSU/CSU (RJ-45) cable and its descriptions.

8 Pin1 Description
1 Transmit
2 Transmit
7 Receive
8 Receive

1Pins 3, 4, 5, and 6 are not used.

WAN Interface Cards (WICs)

WAN interface cards supported on the Cisco 1602-R consist of the following:

  • WIC-1T: 1-port serial, aynchronous and synchronous (T1/E1)

  • WIC-1DSU-56K4: One serial with integrated 56/64 Kbps 4-wire DSU/CSU

  • WIC-1DSU-T1: One serial with integrated T1/Fractional T1 DSU/CSU

  • WIC-1B-S/T: One ISDN BRI S/T

  • WIC-1B-U: One ISDN BRI U with integrated NT-1

Front Panel LEDs

1602r-led.gif

The table below shows the front panel LED functions for the Cisco 1601 and 1602 routers.

LED Color Description
SYSTEM PWR Green The router is on, and DC power is being supplied.
SYSTEM OK Green The router has successfully booted. Blinks during the boot cycle.
LAN ACT Green Data is being sent to or received from the local Ethernet LAN.
LAN COL Yellow Flashing indicates packet collisions on the local Ethernet LAN.
SER 0 CD Green
  • Cisco 1601 has an active connection on the serial port.
  • Cisco 1602 has an active connection on the DSU/CSU port.
SER 0 ACT Green
  • Cisco 1601 serial port is sending or receiving data.
  • Cisco 1602 DSU/CSU port is sending or receiving data.
WIC CD/B1 Green
  • Serial WAN interface card has an active connection on the serial port.
  • ISDN WAN interface card has an ISDN connection on B-channel 1.
WIC ACT/B2 Green
  • WAN interface card serial port is sending or receiving data.
  • WAN interface card ISDN port has a connection on B-channel 2.

Rear Panel LEDs

The table below explains the rear panel LEDs and their functions.

LED Color Description
All Models
LNK (next to Ethernet0 10BaseT) Green Indicates 10BaseT link integrity. This LED is not on when connected to an Ethernet network through the AUI port. The Cisco 1605 has two LNK LEDs, one for each Ethernet 10BaseT port.
OK (next to FLASH PC CARD slot) Green The Flash PC card is correctly installed.
Cisco 1601
RDY Green A serial port cable connection has been made to a modem or DSU/CSU.
Cisco 1602
LOOPBACK Yellow The DSU/CSU is in DSU or CSU loopback mode.
ALARM Yellow An alarm condition exists on the DSU/CSU port.
CARRIER Green Indicates line synchronization or connection on the DSU/CSU port.
Cisco 1603
OK (next to ISDN BRI0 S/T port) Green A physical connection has been established with the ISDN central office switch.
Cisco 1604
NT1 Green A physical connection has been established from the router internal NT1 to the ISDN central office switch.
OK (next to ISDN PHONE port) Green The device connected to the router ISDN S/T port has established a physical connection with the ISDN central office switch.
Cisco 1605
LNK (next to ETHERNET1 10BASET) Green Indicates 10BaseT link integrity for the Ethernet 1 port.
OK (next to WIC slot) Green The WAN interface card is correctly installed in the router.

Related Information

Updated: Jul 07, 2005
Document ID: 46784