CAB-530 MT Serial Cable Specifications

Available Languages

Download Options

  • PDF     (16.4 KB)
    View with Adobe Reader on a variety of devices
Updated:January 27, 2006
Document ID:46802

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Introduction

This document provides the technical and cable specifications for the CAB-530MT serial cable.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

This document is not restricted to specific software and hardware versions.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

CAB-530MT Serial Cable Assembly

The cable gender for this product (part number 72-0797-01) is Male DB-60 to Male DB-25, mode - DTE only.

cab530mt.gif

The CAB-530MT cable is used in the Cisco 7000 family, Cisco 4000 series, Cisco 3600 series, Cisco 2500 series, Cisco 1600 series, Cisco access servers, and AccessPro PC cards. This cable has a male DB-60 connector on the Cisco end and a male DB-25 connector on the network end.

eia-530.gif

EIA-530 DTE Cable Pinouts (DB-60 to DB-25)

The table below shows the EIA-530 DTE cable pinouts (DB-60 to DB-25).

Note: The arrows indicate signal direction:

  • ---> indicates DTE to DCE

  • <--- indicates DCE to DTE

60 Pin1 Signal 25 Pin Signal Direction DTE DCE2
J1-11 J1-12 TxD/RxD+ TxD/RxD- J2-2 J2-14 BA(A), TxD+ BA(B), TxD- ---> --->
J1-28 J1-27 RxD/TxD+ RxD/TxD- J2-3 J2-16 BA(A), RxD+ BB(B), RxD- <--- <---
J1-9 J1-10 RTS/CTS+ RTS/CTS- J2-4 J2-19 CA(A), RTS+ CA(B), RTS- ---> --->
J1-1 J1-2 CTS/RTS+ CTS/RTS- J2-5 J2-13 CB(A), CTS+ CB(B), CTS- <--- <---
J1-3 J1-4 DSR/DTR+ DSR/DTR- J2-6 J2-22 CC(A), DSR+ CC(B), DSR- <--- <---
J1-46 J1-47 Shield_GND MODE_2 J2-1 - Shield - Shorted
J1-48 J1-49 GND MODE_1 - - - - Shorted
J1-5 J1-6 DCD/DCD+ DCD/DCD- J2-8 J2-10 CF(A), DCD+ CF(B), DCD- <--- <---
J1-24 J1-23 TxC/RxC+ TxC/RxC- J2-15 J2-12 DB(A), TxC+ DB(B), TxC- <--- <---
J1-26 J1-25 RxC/TxCE+ RxC/TxCE- J2-17 J2-9 DD(A), RxC+ DD(B), RxC- <--- <---
J1-44 J1-45 LL/DCD Circuit_GND J2-18 J2-7 LL Circuit_ GND ---> -
J1-7 J1-8 DTR/DSR+ DTR/DSR- J2-20 J2-23 CD(A), DTR+ CD(B), DTR- ---> --->
J1-13 J1-14 TxCE/TxC+ TxCE/TxC- J2-24 J2-11 DA(A), TxCE+ DA(B), TxCE- ---> --->

1Any pin not referenced is not connected.

2The EIA-530 interface cannot be operated in DCE mode. A DCE cable is not available for the EIA-530 interface.

Related Information

Revision History

Revision Publish Date Comments
1.0
19-Nov-2003
Initial Release

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

This Document Applies to These Products