PDF(176.1 KB) View with Adobe Reader on a variety of devices
Updated:March 13, 2015
Document ID:1457309028965888
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
EOL6884
Cisco announces the end-of-sale and end-of life dates for the Ciso 4-Port T1/E1 RJ-48 and Serial Interface Network Modules. The last day to order the affected product(s) is April 1, 2010. Customers with active service contracts will continue to receive support from the Cisco Technical Assistance Center (TAC) as shown in Table 1 of the EoL bulletin. Table 1 describes the end-of-life milestones, definitions, and dates for the affected product(s). Table 2 lists the product part numbers affected by this announcement. For customers with active and paid service and support contracts, support will be available until the termination date of the contract, even if this date exceeds the Last Date of Support shown in Table 1.
Table 1. End-of-Life Milestones and Dates for the Ciso 4-Port T1/E1 RJ-48 and Serial Interface Network Modules
Milestone
Definition
Date
End-of-Life Announcement Date
The date the document that announces the end of sale and end of life of a product is distributed to the general public.
October 1, 2009
End-of-Sale Date
The last date to order the product through Cisco point-of-sale mechanisms. The product is no longer for sale after this date.
April 1, 2010
Last Ship Date: HW
The last-possible ship date that can be requested of Cisco and/or its contract manufacturers. Actual ship date is dependent on lead time.
June 30, 2010
End of Routine Failure Analysis Date: HW
The last-possible date a routine failure analysis may be performed to determine the cause of product failure or defect.
April 1, 2011
End of New Service Attachment Date: HW
For equipment and software that is not covered by a service-and-support contract, this is the last date to order a new service-and-support contract or add the equipment and/or software to an existing service-and-support contract.
April 1, 2011
End of Service Contract Renewal Date: HW
The last date to extend or renew a service contract for the product.
June 27, 2014
Last Date of Support: HW
The last date to receive service and support for the product. After this date, all support services for the product are unavailable, and the product becomes obsolete.
March 31, 2015
HW = Hardware OS SW = Operating System Software App. SW = Application Software
Table 2. Product Part Numbers Affected by This Announcement
End-of-Sale Product Part Number
Product Description
Replacement Product Part Number
Replacement Product Description
Additional Information
NM-CEM-4SER
4 Port Serial Circuit Emulation over IP NM
There is currently no replacement product available for this product.
NM-CEM-4SER=
4 Port Serial CEMoIP NM
There is currently no replacement product available for this product.
NM-CEM-4TE1
4 Port T1/E1 Circuit Emulation over IP NM
MWR-2941-DC
MWR 2941-DC Mobile Wireless Router
-
NM-CEM-4TE1=
4 Port T1/E1 CEMoIP NM
MWR-2941-DC
MWR 2941-DC Mobile Wireless Router
-
Product Migration Options
Circuit emulation of time-division multiplexing (T1/E1) can be performed by the Cisco MWR 2941-DC Mobile Wireless Router. Please note the that the MWR-2941-DC is an entire router. It is not a replacement network module that fits into a Cisco Integrated Services Router. There are no replacement circuit emulation T1/E1 or serial network modules that fit into the Cisco Integrated Services Routers. For more information about the Cisco MWR 2941-DC Mobile Wireless Router, see
http://www.cisco.com/en/US/prod/collateral/routers/ps4062/MWR_2941DC_DS.html.
Customers can use the Cisco Technology Migration Program (TMP) to trade-in products and receive credit toward the purchase of new Cisco equipment. For more information about Cisco TMP, customers should work with their Cisco Partner or Cisco account team. Cisco Partners can find additional TMP information on Partner Central at
http://www.cisco.com/web/partners/pr11/incentive/tmp/index.html
Customers may be able to continue to purchase the Ciso 4-Port T1/E1 RJ-48 and Serial Interface Network Modules through the Cisco Certified Refurbished Equipment program. Refurbished units may be available in limited supply for sale in certain countries on a first-come, first-served basis until the Last Date of Support has been reached. For information about the Cisco Certified Refurbished Equipment program, go to: www.cisco.com/go/eos
Service prices for Cisco products are subject to change after the product End of Sale date.
The Cisco Takeback and Recycle program helps businesses dispose properly of surplus products that have reached their end of useful life. The program is open to all business users of Cisco equipment and its associated brands and subsidiaries. For more information, go to:
http://www.cisco.com/web/about/ac227/ac228/ac231/about_cisco_takeback_recycling.html
Feedback